|
|
PDF SY10E111 Data sheet ( Hoja de datos )
| Número de pieza | SY10E111 | |
| Descripción | 5V/3.3V 1:9 DIFFERENTIAL CLOCK DRIVER (w/ENABLE) | |
| Fabricantes | Micrel Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SY10E111 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
5V/3.3V 1:9 DIFFERENTIAL
CLOCK DRIVER (w/ENABLE)
ClockWorks™
SY10E111AE/LE
SY100E111AE/LE
FEATURES
s 5V and 3.3V power supply options
s 200ps part-to-part skew
s 50ps output-to-output skew
s Differential design
s VBB output
s Enable Input
s Voltage and temperature compensated outputs
s 75KΩ input pulldown resistors
s Fully compatible with Motorola MC10/100E111
s Available in 28-pin PLCC package
BLOCK DIAGRAM
IN
IN
EN
VBB
Q0
Q0
Q1
Q1
Q2
Q2
Q3
Q3
Q4
Q4
Q5
Q5
Q6
Q6
Q7
Q7
Q8
Q8
DESCRIPTION
The SY10/100E111AE/LE are low skew 1-to-9 differential
drivers designed for clock distribution in mind. The SY10/
100E111AE/LE's function and performance are similar to
the popular SY10/100E111, with the improvement of lower
jitter and the added feature of low voltage operation. It
accepts one signal input, which can be either differential or
single-ended if the VBB output is used. The signal is fanned
out to 9 identical differential outputs. An enable input is
also provided such that a logic HIGH disables the device by
forcing all Q outputs LOW and all Q outputs HIGH.
The E111AE/LE is specifically designed, modeled and
produced with low skew as the key goal. Optimal design
and layout serve to minimize gate to gate skew within a
device, and empirical modeling is used to determine process
control limits that ensure consistent tpd distributions from
lot to lot. The net result is a dependable, guaranteed low
skew device.
To ensure that the tight skew specification is met it is
necessary that both sides of the differential output are
terminated into 50Ω, even if only one side is being used. In
most applications, all nine differential pairs will be used
and therefore terminated. In the case where fewer that
nine pairs are used, it is necessary to terminate at least the
output pairs on the same package side as the pair(s) being
used on that side, in order to maintain minimum skew.
Failure to do this will result in small degradations of
propagation delay (on the order of 10-20ps) of the output(s)
being used which, while not being catastrophic to most
designs, will mean a loss of skew margin.
The E111AE/LE, as with most other ECL devices, can
be operated from a positive VCC supply in PECL mode.
This allows the E111AE/LE to be used for high performance
clock distribution in +5V/+3.3V systems. Designers can
take advantage of the E111AE/LE's performance to
distribute low skew clocks across the backplane or the
board. In a PECL environment, series or Thevenin line
terminations are typically used as they require no additional
power supplies. For systems incorporating GTL, parallel
termination offers the lowest power by taking advantage of
the 1.2V supply as terminating voltage.
Rev.: D Amendment: /0
1 Rev. Date: October, 1998
1 page  
Micrel
TIMING DIAGRAMS
ClockWorks™
SY10E111AE/LE
SY100E111AE/LE
IN
IN
ts
50%
EN
Q
Q
75 mV
75 mV
Figure 1. Set-up Time
IN
IN
EN
Q
Q
th
50%
75 mV
75 mV
Figure 2. Hold Time
IN
IN
EN
50%
tr
Q
Q
Figure 3. Release Time
PRODUCT ORDERING CODE
5V
Ordering
Code
SY10E111AEJC
SY10E111AEJCTR
Package
Type
J28-1
J28-1
Operating
Range
Commercial
Commercial
VEE Range
(V)
-4.75 to -5.5
-4.75 to -5.5
SY100E111AEJC
SY100E111AEJCTR
J28-1
J28-1
Commercial -4.2 to -5.5
Commercial -4.2 to -5.5
5V
Ordering
Code
SY10E111AEJI
SY10E111AEJITR
SY100E111AEJI
SY100E111AEJITR
Package
Type
J28-1
J28-1
J28-1
J28-1
Operating
Range
Industrial
Industrial
Industrial
Industrial
VEE Range
(V)
-4.75 to -5.5
-4.75 to -5.5
-4.2 to -5.5
-4.2 to -5.5
3.3V
SY10E111LEJC
SY10E111LEJCTR
SY100E111LEJC
SY100E111LEJCTR
J28-1
J28-1
J28-1
J28-1
Commercial
Commercial
Commercial
Commercial
-3.0 to -3.8
-3.0 to -3.8
-3.0 to -3.8
-3.0 to -3.8
3.3V
SY10E111LEJI
SY10E111LEJITR
SY100E111LEJI
SY100E111LEJITR
J28-1
J28-1
J28-1
J28-1
Industrial
Industrial
Industrial
Industrial
-3.0 to -3.8
-3.0 to -3.8
-3.0 to -3.8
-3.0 to -3.8
5
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet SY10E111.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SY10E111 | 5V/3.3V 1:9 DIFFERENTIAL CLOCK DRIVER (w/ENABLE) | Micrel Semiconductor |
| SY10E111A | 1:9 DIFFERENTIAL CLOCK DRIVER | Micrel Semiconductor |
| SY10E111AL | 1:9 DIFFERENTIAL CLOCK DRIVER | Micrel Semiconductor |
| SY10E112 | QUAD DRIVER | Micrel Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |