|
|
|
부품번호 | ITXG77H 기능 |
|
|
기능 | 14.1 XGA Color TFT / LCD Module | ||
제조업체 | IDtech | ||
로고 | |||
omEngineering Specification
ww.DataSheet4U.c Engineering Specification
w mType 14.1 XGA Color TFT/LCD Module
oModel Name:ITXG77H
U.cDocument Control Number : OEM I-77H-01
taSheet4Note:Specification is subject to change without notice. Consequently it is better to contact to
International Display Technology before proceeding with the design
of your product incorporating this module.
www.Da .comSales Support
International Display Technology
.DataSheet4U(C) Copyright International Display Technology 2002 All Rights reserved.
wwwFebruary 4,2002
OEM I-77H-01
1/24
Engineering Specification
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of the CFL Reflector edge.
Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may
be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure ( Notebook PC Bezel, for example),
do not twist nor bent the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are applied
to the TFT Module from outside. Otherwise the TFT Module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury.
Please follow local ordinances or regulations for disposal.
13)Small amount of materials having no flammability grade is used in the LCD module.
The LCD module should be supplied by power complied with requirements of
Limited Power Source (2.11, IEC60950 or UL1950), or be applied exemption
conditions of flammability requirements (4.4.3.3, IEC60950 or UL1950) in an end product.
14)The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit
(2.4, IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.
O The information contained herein is presented only as a guide for the applications of our
products. No responsibility is assumed by International Display Technology for any
infringements of patents or other right of the third partied which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of International
Display Technology or others.
O The information contained herein may be changed without prior notice. It is therefore
advisable to contact International Display Technology before proceeding with the design of
equipment incorporating this product.
(C) Copyright International Display Technology 2002 All Rights reserved.
February 4,2002
OEM I-77H-01
4/24
4페이지 Engineering Specification
3.0 Absolute Maximum Ratings
Absolute maximum ratings of the module is as follows :
Item
Symbol
Min
Supply Voltage
Logic/LCD Drive Voltage
VDD
-0.3
Input Voltage of Signal
CFL Inrush current
CFL Current
CFL Ignition Voltage
Operating Temperature
Operating Relative Humidity
Storage Temperature
Storage Relative Humidity
Vibration
Shock
Vin
ICFLL
ICFL
Vs
TOP
HOP
TST
HST
-0.3
-
-
-
0
8
-20
5
Max
+4.0
Unit
V
Conditions
VDD+0.3
20
6.5
1,600
+50
95
+60
95
1.5 10-200
50 18
V
mA
mArms
Vrms
deg.C
%RH
deg.C
%RH
G Hz
G ms
Note 2
Note 1
Note 1
Note 1
Note 1
Half sine wave.
Note 1 : Maximum Wet-Bulb should be 39 degree C and No condensation.
Note 2 : Duration=50 msec Max.
(C) Copyright International Display Technology 2002 All Rights reserved.
February 4,2002
OEM I-77H-01
7/24
7페이지 | |||
구 성 | 총 24 페이지수 | ||
다운로드 | [ ITXG77H.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
ITXG77 | 14.1 XGA Color TFT / LCD Module | IDtech |
ITXG77C | 14.1 XGA Color TFT / LCD Module | IDtech |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |