Datasheet.kr   

5962-86716xxxx 데이터시트 PDF




Intersil에서 제조한 전자 부품 5962-86716xxxx은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 5962-86716xxxx 자료 제공

부품번호 5962-86716xxxx 기능
기능 ANALOG SWITCH
제조업체 Intersil
로고 Intersil 로고


5962-86716xxxx 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 15 페이지수

미리보기를 사용할 수 없습니다

5962-86716xxxx 데이터시트, 핀배열, 회로
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
A Add two vendors, CAGE 24355 and CAGE 17856. Add device type 02. Make
changes to 1.2.1, 1.3, 1.4, and table I, figure 1, and figure 3. Editorial changes
throughout.
B Remove vendor, CAGE 24355 from device types 01 and 02. Add device type 03.
Table I changes. Editorial changes throughout.
89-11-09
93-03-02
C Update boilerplate to add class V. –rrp
00-09-07
D Update to current requirements. Editorial changes throughout. - drw
03-05-01
APPROVED
M. A. Frye
M. A. Frye
R. Monnin
Raymond Monnin
heet4U.comREV
SSHEET
taREV
SHEET
aREV STATUS
REV
DDDDDDDDDDDDD
OF SHEETS
SHEET
1 2 3 4 5 6 7 8 9 10 11 12 13
.DPMIC N/A
PREPARED BY
wSTANDARD
wMICROCIRCUIT
mDRAWING
Rick Officer
CHECKED BY
Charles E. Besore
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
w .coTHIS DRAWING IS AVAILABLE
FOR USE BY ALL
UDEPARTMENTS
t4AND AGENCIES OF THE
eeDEPARTMENT OF DEFENSE
APPROVED BY
Michael A. Frye
DRAWING APPROVAL DATE
87-01-30
MICROCIRCUIT, LINEAR, CMOS, HIGH SPEED
QUAD SPST ANALOG SWITCH, MONOLITHIC
SILICON
taShAMSC N/A
REVISION LEVEL
D
SIZE
A
CAGE CODE
67268
5962-86716
aSHEET
.DDSCC FORM 2233
wAPR 97
wwDISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
1 OF 13
5962-E370-03




5962-86716xxxx pdf, 반도체, 판매, 대치품
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of
this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue
of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific
exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device
class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Functional diagram. The functional diagram shall be as specified on figure 2.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical
performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient
operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests
for each subgroup are defined in table I.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
D
5962-86716
SHEET
4

4페이지










5962-86716xxxx 전자부품, 판매, 대치품
TABLE I. Electrical performance characteristics – Continued.
Conditions
Test
Symbol
-55°C TA +125°C
V+ = +15 V dc, V- = -15 V dc
unless otherwise specified
Capacitance address
CA
Capacitance input switch CIS
Capacitance output
switch
Off isolation
COS
VISO
Crosstalk between
channels
Charge transfer error
VCT
VCTE
GND = 0 V, VIL = 0 V,
f = 1 MHz, TA = +25°C
GND = 0 V, VIH = 5 V,
f = 1 MHz, TA = +25°C
GND = 0 V, VIH = 5 V,
f = 1 MHz, TA = +25°C
4/
4/
4/
VGEN = 1 VP-P, f = 100 kHz,
TA = +25°C 2/
VGEN = 1 VP-P, f = 100 kHz,
TA = +25°C 2/
TA = +25°C 2/
Group A
subgroups
4
4
4
4
4
4
Device
type
Limits 1/
Min Max
All 15
All 15
All 20
All 60
All 60
All ±10
Unit
pF
pF
pF
dB
dB
mV
1/ The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative current
shall be defined as conventional current flow out of a device terminal.
2/ These parameters may not be tested, but shall be guaranteed to the limits specified in table I herein.
3/ Test not required if applied as a forcing function.
4/ Subgroup 4 (CA, CIS, and COS measurements) shall be measured only for the initial test and after process or design changes
which may affect capacitance.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked
as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the
manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator
shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M
shall be in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed
manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing
shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or
for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein)
involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A.
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available
onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit
group number 82 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
D
5962-86716
SHEET
7

7페이지


구       성 총 15 페이지수
다운로드[ 5962-86716xxxx.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
5962-86716xxxx

ANALOG SWITCH

Intersil
Intersil

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵