Datasheet.kr   

BGB100 데이터시트 PDF




NXP Semiconductors에서 제조한 전자 부품 BGB100은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 BGB100 자료 제공

부품번호 BGB100 기능
기능 0 dBm TrueBlue radio module
제조업체 NXP Semiconductors
로고 NXP Semiconductors 로고


BGB100 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 16 페이지수

미리보기를 사용할 수 없습니다

BGB100 데이터시트, 핀배열, 회로
DISCRETE SEMICONDUCTORS
DATA SHEET
BGB100
0 dBm TrueBlue radio module
Preliminary specification
2002 Jan 03




BGB100 pdf, 반도체, 판매, 대치품
Philips Semiconductors
0 dBm TrueBlue radio module
Preliminary specification
BGB100
QUICK REFERENCE DATA
VS = 3.0 V; Tamb = 25 °C; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
VS
IS1 + IS2
Sens
Pout
f0
fref
Tamb
nominal supply voltage
total supply current
receiver sensitivity
output power
RF frequency
reference input frequency
operating ambient temperature(1)
during RX guard space
during demodulation
during TX guard space
during transmission
in power-down mode
BER = 0.1 % under standard
conditions
at nominal settings
2.8
4
2402
12
10
3
25
60
36
34
10
80
−1.5
3.6 V
mA
72 mA
mA
40 mA
60 µA
73 dBm
+4
2480
26
55
dBm
MHz
MHz
°C
Note
1. In combination with the adaptive temperature-compensation scheme provided by the baseband processor
FUNCTIONAL DESCRIPTION
Control
The BGB100 TrueBlue Bluetooth Radio Module is controlled by a baseband processor via the serial 3-wire bus. These
3 wires are data (S_DATA), clock (S_CLK) and enable (S_EN). Data sent to the device is loaded in bursts framed by
S_EN. Data and clock (S_DATA and S_CLK) signals are ignored until S_EN goes low. The programmed information is
read directly into the internal registers when S_EN goes high. S_DATA and S_EN should be stable around the rising
edges of S_CLK. There are internal pull-down resistors on all these three pins.
Only the last 32 bits serially clocked into the device are retained within the register. Additional (leading) bits are ignored,
and no check is made on the number of bits received. The data format is shown in table 1. The first data bit entered is
b31, the last one b0.
The S_EN high-to-low transition also controls the opening of the PLL. A short S_EN high pulse at the end of a time slot,
either TX or RX, serves to reset and power-down the IC. This can be omitted, at the cost of extra power consumption.
In addition to the 3-wire serial bus, there is one control signal used for accurate timing of functions within the IC, under
control by the baseband processor. This is the DCXCTR signal, to control (in RX mode) the three subsequent operating
modes of the DC compensation circuit: coarse offset estimation during the early part of the Access Code, accurate offset
estimation during the Barker sequence and the trailer, retention of the offset information during the payload.
Transmit mode
The BGB100 TrueBlue Bluetooth Radio Module contains a fully integrated transmitter function. The RF channel
frequency is selected in a conventional synthesizer, which is controlled via the serial 3-wire bus. The VCO is directly
modulated by the signal present on the T_GFSK connection. The Gaussian filtering should therefore be performed
externally. The DC bias voltage for this pin should already be present during the S_EN programming pulse, so that the
PLL can correct for possible frequency errors that might otherwise occur. Also in RX mode, this pin should be connected
to a well-defined and stable DC voltage. The robust design of the VCO makes it unnecessary to trim its freerunning
frequency. This leads to a lower component cost. A carefully designed PLL loop filter keeps frequency drift during
open-loop modulation down to a very low value.
2002 Jan 03
4

4페이지










BGB100 전자부품, 판매, 대치품
Philips Semiconductors
0 dBm TrueBlue radio module
Preliminary specification
BGB100
Table 4 Typical output programming
b11
0
0
1
1
b10
0
1
0
1
TYPICAL OUTPUT POWER
4.5 dBm
1.5 dBm (nominal value)
1.5 dBm
3.5 dBm
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
CONDITIONS
VS1, VS2
GND
Ptot
PD
Tstg
Tj
supply voltage
input control pin voltage
difference in ground supply
voltage between ground pins
total power dissipation
drive power at receiver input
storage temperature
junction temperature
MIN.
0.3
0.3
MAX.
3.6
VS
0.01
UNIT
V
V
V
tbd W
0 dBm
55 85
°C
150 °C
THERMAL CHARACTERISTICS
SYMBOL
PARAMETER
Rth j-a
thermal resistance from junction to ambient
VALUE
tbd
UNIT
K/W
SPURIOUS EMISSIONS
The conducted and radiated out-of-band spurious emissions in all operating modes are fully compliant with the
Regulatory Requirement FCC Part 15.247,C and ETS 300 328 (subclause 5.2.4.).
ESD PRECAUTIONS
Inputs and outputs are protected against electrostatic discharge (ESD) during handling and mounting. A human-body
model (HBM) and a machine model (MM) are used for ESD susceptibility testing. All pins withstands the following
threshold voltages:
PARAMETER
ESD threshold voltage
METHOD
HBM (JESD22-A114-B)
MM (JESD22-A115-A)
VALUE
3500 V
300 V
CLASS
2
2
2002 Jan 03
7

7페이지


구       성 총 16 페이지수
다운로드[ BGB100.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
BGB100

0 dBm TrueBlue radio module

NXP Semiconductors
NXP Semiconductors
BGB101

0 dBm Bluetooth radio module

NXP Semiconductors
NXP Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵