|
|
PDF TSOP36230 Data sheet ( Hoja de datos )
| Número de pieza | TSOP36230 | |
| Descripción | (TSOP362xx) IR Receiver Modules | |
| Fabricantes | Vishay Intertechnology | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TSOP36230 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
TSOP362..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
Description
The TSOP362.. - series are miniaturized SMD-IR
Receiver Modules for infrared remote control sys-
tems. PIN diode and preamplifier are assembled on
lead frame, the epoxy package is designed as IR fil-
ter.
The demodulated output signal can directly be
decoded by a microprocessor. TSOP362.. is the stan-
dard IR remote control SMD-Receiver series, for 3 V
supply voltage supporting all major transmission
codes.
4
3
2
1
16797
Features
• Photo detector and preamplifier in one
package
• Internal filter for PCM frequency
• Continuous data transmission possible e3
• TTL and CMOS compatibility
• Output active low
• Low power consumption
• High immunity against ambient light
• Supply voltage: 2.7 V to 5.5 V
• Lead (Pb)-free component
• Component in accordance to RoHS 2002/95/EC
and WEEE 2002/96/EC
Special Features
• Improved immunity against ambient light
• Suitable burst length (≥ 10 cycles/burst)
• Taping available for topview and sideview
assembly
Block Diagram
16839
30 kΩ
Input
AGC
Band Demo-
Pass dulator
PIN Control Circuit
3
VS
4
OUT
1;2
GND
Mechanical Data
Pinning:
1 = GND, 2 = GND, 3 = VS, 4 = OUT
Parts Table
Part
TSOP36230
TSOP36233
TSOP36236
TSOP36237
TSOP36238
TSOP36240
TSOP36256
Carrier Frequency
30 kHz
33 kHz
36 kHz
36.7 kHz
38 kHz
40 kHz
56 kHz
Application Circuit
17403
Transmitter
with
TSALxxxx
HSxxxx
R1 = 100 Ω
VS C1 =
4.7 μF
OUT
GND
VO
+VS
μC
GND
R1 + C1 recommended to suppress power supply
disturbances.
The output voltage should not be hold continuously at
a voltage below VO = 2.0 V by the external circuit.
Document Number 82187
Rev. 1.5, 17-Nov-05
www.vishay.com
1
1 page  
www.DataSheet4U.com
TSOP362..
Vishay Semiconductors
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
17185
VS – Supply Voltage ( V )
Figure 13. Sensitivity vs. Supply Voltage
Suitable Data Format
The circuit of the TSOP362.. is designed in that way
that unexpected output pulses due to noise or distur-
bance signals are avoided. A bandpass filter, an inte-
grator stage and an automatic gain control are used
to suppress such disturbances.
The distinguishing mark between data signal and dis-
turbance signal are carrier frequency, burst length
and duty cycle.
The data signal should fulfill the following conditions:
• Carrier frequency should be close to center fre-
quency of the bandpass (e.g. 38 kHz).
• Burst length should be 10 cycles/burst or longer.
• After each burst which is between 10 cycles and 70
cycles a gap time of at least 14 cycles is necessary.
• For each burst which is longer than 1.8 ms a corre-
sponding gap time is necessary at some time in the
data stream. This gap time should be at least 6 times
longer than the burst.
• Up to 800 short bursts per second can be received
continuously.
Some examples for suitable data format are: NEC
Code (repetitive pulse), NEC Code (repetitive data),
Toshiba Micom Format, Sharp Code, RC5 Code,
RC6 Code, R-2000 Code, Sony Code.
When a disturbance signal is applied to the
TSOP362.. it can still receive the data signal. How-
ever the sensitivity is reduced to that level that no
unexpected pulses will occur.
Some examples for such disturbance signals which
are suppressed by the TSOP362.. are:
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signal at 38 kHz or at any other fre-
quency
• Signals from fluorescent lamps with electronic bal-
last with high or low modulation
(see Figure 14 or 15).
IR Signal from fluorescent
lamp with low modulation
16920
0
5 10 15
Time (ms)
20
Figure 14. IR Signal from Fluorescent Lamp with low Modulation
IR Signal from fluorescent
lamp with high modulation
16921
0
5 10 15
Time (ms)
20
Figure 15. IR Signal from Fluorescent Lamp with high Modulation
Document Number 82187
Rev. 1.5, 17-Nov-05
www.vishay.com
5
5 Page 
www.DataSheet4U.com
Leader and Trailer
Trailer
no devices
End
min. 200
devices
Cover Tape Peel Strength
According to DIN EN 60286-3
0.1 to 1.3 N
300 ± 10 mm/min
165 ° - 180 ° peel angle
Label
Standard bar code labels for finished goods
The standard bar code labels are product labels and
used for identification of goods. The finished goods
are packed in final packing area. The standard pack-
ing units are labeled with standard bar code labels
before transported as finished goods to warehouses.
The labels are on each packing unit and contain
Vishay Semiconductor GmbH specific data.
TSOP362..
Vishay Semiconductors
Leader
no devices
min. 400
Start
96 11818
Document Number 82187
Rev. 1.5, 17-Nov-05
www.vishay.com
11
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet TSOP36230.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TSOP36230 | (TSOP362xx) IR Receiver Modules | Vishay Intertechnology |
| TSOP36233 | (TSOP362xx) IR Receiver Modules | Vishay Intertechnology |
| TSOP36236 | (TSOP362xx) IR Receiver Modules | Vishay Intertechnology |
| TSOP36237 | (TSOP362xx) IR Receiver Modules | Vishay Intertechnology |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |