Datasheet.kr   

LB064V02-TD01 데이터시트 PDF




Philips에서 제조한 전자 부품 LB064V02-TD01은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 LB064V02-TD01 자료 제공

부품번호 LB064V02-TD01 기능
기능 LCD Module
제조업체 Philips
로고 Philips 로고


LB064V02-TD01 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 24 페이지수

미리보기를 사용할 수 없습니다

LB064V02-TD01 데이터시트, 핀배열, 회로
www.DataSheet4U.com
Product Specification
SPECIFICATION
FOR
APPROVAL
LB064V02
Liquid Crystal Display
( ) Preliminary Specification
( ) Final Specification
Title
BUYER
MODEL
6.4” V (640 X RGB X 480 ) TFT – LCD
SUPPLIER
MODEL
DataSheet4U.com SUFFIX
LG.Philips LCD Co., Ltd.
LB064V02
TD01
DataShee
SIGNATURE
/
/
/
DATE
SIGNATURE
C. S. Kyung / G.Manager
REVIEWED BY
DATE
S. D. Jung / Manager
PREPARED BY
H.Y.Park / Project Leader
Please return 1 copy for your confirmation with
your signature and comments.
Products Engineering Dept.
LG. Philips LCD Co., Ltd
Ver. 1.0
DataSheet4U.com
Aug. 30, 2005
1 / 24
DataSheet4 U .com




LB064V02-TD01 pdf, 반도체, 판매, 대치품
www.DataSheet4U.com
Product Specification
LB064V02
Liquid Crystal Display
1. Summary
This module utilizes amorphous silicon thin film transistors. A 6.4” active matrix liquid crystal display
allows full color to be displayed.
2. Features
•The 6.4” screen produces a high resolution image that is composed of 307,200 pixel elements in a stripe
arrangement.
• Wide viewing angle technology is employed.
[The most suitable viewing direction is in the 6 o’clock direction.]
• By adopting an active matrix drive, a picture with high contrast is realized.
• A thin, light and compact module is accomplished through the use of COF mounting technology.
• By adopting a high aperture panel, high transmittance color filter and high transmission polarizing plates,
transmittance ratio is realized.
• Gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal.
et4U.com
DataSheet4U.com
DataShee
* CN1: GT101-30S-HR11 or equivalent
* CN2: BHSR-02VS-1(JST)
Ver. 1.0
DataSheet4U.com
Aug. 30, 2005
DataSheet4 U .com
4 / 24

4페이지










LB064V02-TD01 전자부품, 판매, 대치품
www.DataSheet4U.com
et4U.com
LB064V02
Liquid Crystal Display
Product Specification
.
This phenomenon is caused by interference between lamp (CCFL) lighting frequency and
LCD horizontal synchronous signal.)
* 4. . The “MAX” of “Kick-Off Voltage” means the minimum voltage for inverter to turn on the CCFL
normally in the LCD module. However this isn’t the values that we can assure stability of
starting lamp on condition that the module is installed in your set.
It should be careful that “Kick-Off Voltage” is changed by an increase of stray capacitance in
your set, inverter method, value of ballast capacitor in your inverter and so on.
Especially, the value of “Kick-Off Voltage” is higher in low temperature condition than in
normal temperature condition, because impedance of CCFL is increased.
The voltage above VS should be applied to the lamps for more than 1 second for start-up.
Otherwise, the lamps may not be turned on. The used lamp current is the lamp typical current.
* 5. The time needed to achieve not less than 95%brightness of the center part of lamp.
The brightness of the lamp after being lighted for 5 minutes is defined as 100%.
* 6. “Life time” is defined as the time that the lamp brightness decreases to 50% from original brightness
at IBL=TYP; continuous lighting, Ta=25 .
Requirements for a system inverter design, which is intended to have a better display performance, a
better power efficiency and a more reliable lamp, are as follows. It shall help increase the lamp lifetime
and reduce leakage current. Inverter should be designed to be subject to the conditions below
A. The asymmetry rate of the inverter waveform should be less than 10%.
B. The distortion rate of the waveform should be within 2 ± 10%.
* Inverter output waveform had better be more similar to ideal sine wave.
DataSheet4U.com
* Asymmetry rate:
Ip
( I p – I –p |) / Irms * 100%
I -p •Distortion rate:
I p (or I –p) / Irms
DataShee
C. There should not be any spikes in the waveform.
D. Lamp current should not exceed the “MAX” value under the “Operating Temperature” (it is
prohibited to exceed the “MAX.” value even if it is operated in the guaranteed temperature).
When lamp current exceed the maximum value for a long time, it may cause a smoking and
Ignition.
Therefore, it is recommended that the inverter have the current limited circuit that is used as a
protection circuit and/or the lamp current-controlled inverter.
Do not attaches a conducting tape to lamp connecting wire.
If the lamp wire attach to a conducting tape, TFT-LCD Module has a low luminance and the inverter
has abnormal action. Because leakage current is occurred between lamp wire and conducting tape.
5-2. Interface Connections
This LCD employs Two interface connections, a 30 pin connector is used for the module electronics interface
and the other connectors is used for the integral backlight system.
The electronics interface connector is a model GT101-30S-HR11 manufactured by LS Cable
Ver. 1.0
DataSheet4U.com
Aug. 30, 2005
7 / 24
DataSheet4 U .com

7페이지


구       성 총 24 페이지수
다운로드[ LB064V02-TD01.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
LB064V02-TD01

LCD Module

Philips
Philips

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵