Datasheet.kr   

VJ0603Axxxxxx 데이터시트 PDF




Vishay Intertechnology에서 제조한 전자 부품 VJ0603Axxxxxx은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 VJ0603Axxxxxx 자료 제공

부품번호 VJ0603Axxxxxx 기능
기능 (VJ0805Axxxx) Surface Mount Multilayer Chip Capacitors
제조업체 Vishay Intertechnology
로고 Vishay Intertechnology 로고


VJ0603Axxxxxx 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 7 페이지수

미리보기를 사용할 수 없습니다

VJ0603Axxxxxx 데이터시트, 핀배열, 회로
www.DataSheet4U.com
Class 1 NP0 10/16/25/50/100 V
Vishay BCcomponents
Surface Mount Multilayer Chip Capacitors
FEATURES
Ultra stable class 1 dielectric
Four standard sizes
High capacitance per unit volume
Supplied in tape on reel
For high frequency applications
Ni-barrier with 100 % tin terminations
GENERAL SPECIFICATIONS
NOTE: Electrical characteristics values -
temperature at 20 ± 1 °C, pressure at 86 to 106 Kpa and
humidity at 63 to 67 % unless otherwise stated
Rated Voltage UR (DC): 10 V; 16 V; 25 V; 50 V; 100 V
Capacitance Range: 1.0 pF to 0.039 µF
Tolerance on Capacitance:
C 10 pF = ± 1 %; ± 2 %; ± 5 %; ± 10 %
C < 10 pF = ± 0.1 pF; ± 0.5 pF; ± 0.25 pF
APPLICATIONS
Consumer electronics
Telecommunications
Data processing
Tolerance on Capacitance (cont):
Q 30 pF = Q 1000
Q < 30 pF = Q 400 + 20C
Temperature Coefficient: ± 30 ppm/ °C
Insulation Resistance after 120 seconds at UR (DC):
10 Gminimum or 500 F minimum, whichever is less
Climatic Category (IEC 68): 55/125/56
DIMENSIONS in inches [millimeters]
T
MB MB
L
W
DataSheet4U.com
SIZE
CODE
L
W
0402
0.040 ± 0.002 0.020 ± 0.002
[1.0 ± 0.05] [0.5 ± 0.05]
T
MAX.
0.022
[0.55]
MB
0.010 + 0.002/- 0.004
[0.25 + 0.05/- 0.1]
0603
0.063 ± 0.004 0.030 ± 0.003
[1.6 ± 0.10] [0.8 ± 0.07]
0.035
[0.87]
0.015 ± 0.006
[0.40 ± 0.15]
0805
1206
0.080 ± 0.006 0.050 ± 0.004
[2.0 ± 0.15] [1.25 ± 0.10]
0.125 ± 0.006
[3.2 ± 0.15]
0.063 ± 0.006
[1.6 ± 0.15]
0.063 ± 0.008
[1.6 ± 0.20]
0.053
[1.35]
0.069
[1.8]
0.020 ± 0.008
[0.50 ± 0.20]
0.025 ± 0.008
[0.60 ± 0.20]
DataShee
ORDERING INFORMATION
VJ0402
A
SIZE CODE DIELECTRIC
101
CAPACITANCE
J XQ
TOLERANCE TERMINATION VOLTAGE
0402
0603
0805
1206
DataSheet4U.com
A = COG (NP0)
two significant digits
followed by the
number of zeros:
101 = 100
102 = 1000
152 = 1500
103 = 10000
B = ± 0.1 pF
C = ± 0.25 pF
D = ± 0.50 pF
F=±1%
G=±2%
J=±5%
K = ± 10 %
X = Ni Barrier
Q = 10 V
J = 16 V
X = 25 V
A = 50 V
B = 100 V
www.vishay.com
2
For technical questions contact [email protected]
DataSheet4 U .com
C
PACKAGING
C = 7 inches
reel/paper
P = 13 inches
reel/paper
T = 7 inches
reel/blister
R = 13 inches
reel/blister
W1BC
TECHNOLOGY
Document Number 28501
Revision 18-Sep-03




VJ0603Axxxxxx pdf, 반도체, 판매, 대치품
www.DataSheet4U.com
Class 1 NP0 10/16/25/50/100 V
Surface Mount Multilayer Chip Capacitors Vishay BCcomponents
BLISTER TAPE SPECIFICATIONS
P0
D0 P2
E
F
W
B0
A0
P1
D1
direction of unreeling
DIMENSIONS OF BLISTER TAPE in millimeters
DIMENSION
A0
B0
W
E
F
D0
D1
P0
P1
P2
PRODUCT
0805 1206
< 1.55 < 2.00
< 2.45 < 3.60
8.00 8.00
1.75 1.75
3.50 3.50
1.50 1.50
1.00 1.00
4.00 4.00
4.00 4.00
2.00 2.00
TOLERANCE
-
-
± 0.20
± 0.10
± 0.05
+ 0.10/ - 0
± 0.10
± 0.05
± 0.10
± 0.05
REEL SPECIFICATIONS
et4U.com
DataSheet4U.com
A
DC
DataShee
B
REEL DIMENSIONS AND TAPE WIDTH in millimeters
180 mm; 7 inch
A 13.0 ± 1.0
B 9.0 ± 1.0
C 178.0 ± 1.0
D 60.5 ± 1.0
330 mm; 13 inch
13.0 ± 0.5
9.0 ± 0.5
330.0 ± 1.0
100.0 ± 1.0
METHOD OF MOUNTING AND DIMENSIONS OF SOLDER LANDS
For normal use the capacitors may be mounted on printed-circuit boards or ceramic substrates by applying wave soldering and
reflow soldering.
An improper combination of soldering, substrate and chip size can lead to a damaging of the component. The risk increases with
the chip size and with temperature fluctuations (> 100 °C) Therefore, it is advised to use the smallest possible size and follow
the dimensional recommendations given.
DataSheet4U.com
Document Number 28501
Revision 18-Sep-03
For technical questions contact [email protected]
www.vishay.com
5
DataSheet4 U .com

4페이지










VJ0603Axxxxxx 전자부품, 판매, 대치품
www.DataSheet4U.com
Class 1 NP0 10/16/25/50/100 V
Vishay BCcomponents Surface Mount Multilayer Chip Capacitors
et4U.com
TEST PROCEDURES AND REQUIREMENTS
TEST
PROCEDURE
Resistance to soldering
heat
260 ± 5 °C for 10 ± 1 second;
Solder: SN63A;
Measurement after 24 ± 2 hours at room temperature
Preheating: 120 to 150 °C for 1 minute before immerse
the capacitor in a eutectic solder.
Temperature cycle
55 to 125 °C; 5 cycles in the following sequence:
55 °C 3/+ 0 for 30 ± 3 minutes;
Room temperature for 2 to 3 minutes;
125 °C + 3/0 for 30 ± 3 minutes;
Room temperature for 2 to 3 minutes
Measurement after 24 ± 2 hours at room temperature
Humidity test
(damp heat steady state)
40 ± 2 °C; 90 to 95 % RH for
500 + 24/0 hours UR applied;
Measurement after 24 ± 2 hours at room temperature
Humidity load
(damp heat)
40 ± 2 °C; 90 to 95 % RH for
500 + 24/0 hours
Measurement after
UR
24
applied;
± 2 houDrsaattarSoohmeetetm4Upe.rcaotumre
Adhesive strength of
termination
Vibration resistance
Pressurizing force 5 N (0603) and 10 N (> 0603)
Test time 10 ± 1 second
Frequency: 10 to 55 Hz/minute;
Total amplitude: 1.5 mm
Test time: 6 hours (2 hours each in 3 mutually
perpendicular directions)
High temperature load
(endurance)
Test temperature: 125 ± 3 °C;
200 % of rated voltage for 1000 + 24/0 hours;
Measurement after 24 ± 2 hours at room temperature
REQUIREMENTS
no visible damage
C/C: ± 2.5 % maximum or ± 0.25 pF maximum,
whichever is greater
DF, Rins and dielectric strength to meet initial
requirements
no visible damage
C/C: ± 2.5 % maximum or ± 0.25 pF maximum,
whichever is greater
DF, Rins and dielectric strength to meet initial
requirements
no visual damage
C/C: ± 5.0 % maximum or ± 0.5 pF maximum,
whichever is greater
Q: 30 pF Q 350
10 pF C < 30 pF, Q 275 + 2.5C
< 10 pF, Q 200 + 10C
Rins: 1 Gminimum or 50 F minimum,
whichever is less
no visual damage
C/C: 7.5 % maximum or ± 0.75 pF maximum,
whichever is greater
Q: 30 pF, Q 200
C < 30 pF, Q 100 + 10/3C
Rins: 500 Mminimum or 25 F minimum,
whichever is less
no visible damage
no visible damage or removal of the terminations
Capacitance change and DF: to meet initial
requirements
no visual damage
C/C: ± 3 % maximum or 0.3 pF maximum,
whichever is greater
Q: 30 pF, Q 350
10 pF C < 30 pF, Q 275 + 2.5C
C < 10 pF, Q 200 + 10C
Rins: 1 Gminimum or 50 F minimum,
whichever is less
DataSheet4U.com
www.vishay.com
8
DataSheet4 U .com
For technical questions contact [email protected]
Document Number 28501
Revision 18-Sep-03

7페이지


구       성 총 7 페이지수
다운로드[ VJ0603Axxxxxx.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
VJ0603Axxxxxx

(VJ0805Axxxx) Surface Mount Multilayer Chip Capacitors

Vishay Intertechnology
Vishay Intertechnology

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵