|
|
PDF AT78C5091 Data sheet ( Hoja de datos )
| Número de pieza | AT78C5091 | |
| Descripción | 1-CHANNEL SERIAL ATA PHY | |
| Fabricantes | ATMEL Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AT78C5091 (archivo pdf) en la parte inferior de esta página. Total 3 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Features
• 1.5 Gbps Bi-directional Transceiver
– Compliant with Serial ATA Gen1 Revision 1.0a Specification
• Low Power Operation
– 75 mW per Channel Nominal
• Key Blocks Include
– Integrated OOB Processor
– K28.5 COMMA Detection
– Digital Clock and Data Recovery (CDR) with Digital Equalization
– Spread Spectrum Clocking
– Optional 8B/10B Encoder and Decoder
• Parallel I/O
– Synchronous 8-bit/10-bit Parallel Interface @ 150 MHz
• Serial I/0
– Programmable Pre-emphasis
– Support for Spread Spectrum Clocking
– Integrated 100Ω Matched Differential Termination
– AC and DC Coupling Support
• Test Features
– Far-end and Near-end Loopback Support
– At Speed BIST
Overview
The AT78C5091 is a 1-channel SATA PHY supporting Gen 1 speeds of 1.5 Gbps. The
IP has been designed based on the requirements stated in the Serial ATA Standard,
Rev 1.0a, Jan 2003.
On the transmit path, parallel data is registered, passed through a transmit FIFO to
compensate for phase differences between the link and PHY clocks, 8B/10B encoded
and then passed out via a high speed serializer using a spread spectrum clock. Built-
in flexibility permits bypassing the encoding block in addition to optionally disabling the
spread spectrum clocking. The user can control the transmit buffer output swing and
pre-emphasis levels via direct input signals.
On the receive path, the AT78C5091 performs the serial-to-parallel conversion, using
a high bandwidth clock and data recovery (CDR) block. The recovered data is then
passed through a comma alignment block and an optional 8B/10B decode block
before being passed to the phyCtrl layer via a parallel interface. This interface is syn-
chronous to the recovered clock.
The PHY core has an out of band (OOB) processor. As specified by the Serial ATA
standard, three out of band (OOB) signals are used/detected by the PHY, namely
COMRESET, COMINIT, and COMWAKE. Each of these signals are indicated by a
number of bursts of four ALIGN primitives followed by defined idle periods during
which the differential voltage on the serial line is null. OOB signals are observed by
detecting the temporal spacing between adjacent bursts of activity.
Test functions including BIST, scan, parallel and serial loopback modes are configured
and controlled by the use of direct input signals. Similarly, error/status bits are indi-
cated through direct output signals such as bistErr.
1-channel
Serial ATA PHY
AT78C5091
Summary
3558AS–NETST–5/05
Note: This is a summary document. A complete document
is available under NDA. For more information, please con-
tact your local Atmel sales office.
1 page | ||
| Páginas | Total 3 Páginas | |
| PDF Descargar | [ Datasheet AT78C5091.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AT78C5090 | 2-CHANNEL SERIAL ATA PHY | ATMEL Corporation |
| AT78C5091 | 1-CHANNEL SERIAL ATA PHY | ATMEL Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |