Datasheet.kr   

EL7536 데이터시트 PDF




Intersil Corporation에서 제조한 전자 부품 EL7536은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 EL7536 자료 제공

부품번호 EL7536 기능
기능 Monolithic 1A Step-Down Regulator
제조업체 Intersil Corporation
로고 Intersil Corporation 로고


EL7536 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 9 페이지수

미리보기를 사용할 수 없습니다

EL7536 데이터시트, 핀배열, 회로
www.DataSheet4U.com
NOTPROESCSOIBMLMEESNUDIBSESL®DT97FIT5OU3RT6ENDEPaWRtaODDSEUhSeCIGeTtNS
Monolithic 1A Step-Down Regulator
The EL7536 is a synchronous, integrated FET 1A step-down
regulator with internal compensation. It operates with an
input voltage range from 2.5V to 5.5V, which accommodates
supplies of 3.3V, 5V, or a Li-Ion battery source. The output
can be externally set from 0.8V to VIN with a resistive
divider.
The EL7536 features PWM mode control. The operating
frequency is typically 1.4MHz. Additional features include a
100ms Power-On-Reset output, <1µA shut-down current,
short-circuit protection, and over-temperature protection.
The EL7536 is available in the 10 Ld MSOP package,
making the entire converter occupy less than 0.15in2 of PCB
area with components on one side only. Both packages are
specified for operation over the full -40°C to +85°C
temperature range.
Ordering Information
PART NUMBER PART TAPE &
PKG.
(BRAND)
MARKING REEL PACKAGE DWG. #
EL7536IY
BDAAA
- 10 Ld MSOP MDP0043
EL7536IY-T7 BDAAA
7” 10 Ld MSOP MDP0043
EL7536IY-T13 BDAAA
13” 10 Ld MSOP MDP0043
EL7536IYZ
(Note)
BFAAA
- 10 Ld MSOP MDP0043
(Pb-free)
EL7536IYZ-T7 BFAAA
(Note)
7” 10 Ld MSOP MDP0043
(Pb-free)
EL7536IYZ-T13 BFAAA
(Note)
13” 10 Ld MSOP MDP0043
(Pb-free)
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
Pinout
EL7536 (10 LD MSOP)
TOP VIEW
1 SGND
2 PGND
3 LX
4 VIN
5 VDD
FB 10
VO 9
POR 8
EN 7
RSI 6
July 13, 2006
EL7536
FN7396.8
Features
• Less than 0.15in2 (0.97cm2) footprint for the complete 1A
converter
• Components on one side of PCB
• Max height 1.1mm MSOP10
• 100ms Power-On-Reset output (POR)
• Internally-compensated voltage mode controller
• Up to 94% efficiency
• <1µA shut-down current
• Overcurrent and over-temperature protection
• Pb-free plus anneal available (RoHS compliant)
Applications
• PDA and pocket PC computers
• Bar code readers
• Cellular phones
• Portable test equipment
• Li-Ion battery powered devices
• Small form factor (SFP) modules
Typical Application Diagram
EL7536
TOP VIEW
VS (2.5V to 5.5V)
L1
R3 100Ω
VIN
VDD
LX 1.8µH
C1
10µF
C2 C3
10µF
0.1µF
EL7536
VO
R5 100kΩ
R4 100kΩ
R6
100kΩ
POR
EN
RSI
PGND
SGND
R1*
124kΩ
FB
R2*
100kΩ
C4
470pF
VO (1.8V @ 1A)
* VO = 0.8V * (1 + R1 / R2)
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003-2006. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.




EL7536 pdf, 반도체, 판매, 대치품
EL7536
Performance Curves and Waveforms
All waveforms are taken at VIN = 3.3V, VO = 1.8V, IO = 1A with component values shown on page 1 at room ambient temperature, unless otherwise
noted.
100 VIN=5V
95 VO=3.3V
90
85
80 VO=1.8V
75 VO=1.2V
70
65
60
0 200 400 600
IO (mA)
VO=2.5V
800 1000
FIGURE 1. EFFICIENCY
100 VIN=3.3V
95
90
85
80 VO=1V
75
70
65
60
0 200
VO=1.8V
400 600
IO (mA)
VO=2.5V
VO=1.2V
800 1000
FIGURE 2. EFFICIENCY
1.44
1.42
VIN=5V IO=1A
VIN=3.3V IO=1A
VIN=5V IO=0A
1.4
1.38
VIN=3.3V IO=0A
1.36
1.34
1.32
-50
0 50
TA (°C)
100
150
FIGURE 3. FS vs JUNCTION TEMPERATURE
0.1%
0.0%
-0.1%
-0.2%
-0.3%
VIN=3.3V
VIN=5V
-0.4%
-0.5%
0
0.2 0.4 0.6 0.8
IO (A)
FIGURE 4. LOAD REGULATIONS
1
0.1%
0.0%
-0.1%
-0.2%
VIN=3.3V IO=0A
VIN=5V IO=0A
-0.3%
-0.4%
VIN=3.3V IO=1A
-0.5%
-0.6%
VIN=5V IO=1A
-0.7%
-50
0 50 100 150
TJ (°C)
FIGURE 5. LOAD/LINE REGULATIONS vs JUNCTION
TEMPERATURE
12
10
8
6
4
2
0
2.5 3 3.5 4 4.5 5
VIN (V)
FIGURE 6. NO LOAD INPUT CURRENT
4 FN7396.8
July 13, 2006

4페이지










EL7536 전자부품, 판매, 대치품
EL7536
Applications Information
Product Description
The EL7536 is a synchronous, integrated FET 1A step-down
regulator which operates from an input of 2.5V to 6V. The
output voltage is user-adjustable with a pair of external
resistors.
The internally-compensated controller makes it possible to
use only two ceramic capacitors and one inductor to form a
complete, very small footprint 1A DC:DC converter.
Start-Up and Shut-Down
When the EN pin is tied to VIN, and VIN reaches
approximately 2.4V, the regulator begins to switch. The
output voltage is gradually increased to ensure proper soft-
start operation.
When the EN pin is connected to a logic low, the EL7536 is
in the shut-down mode. All the control circuitry and both
MOSFETs are off, and VOUT falls to zero. In this mode, the
total input current is less than 1µA.
When the EN reaches logic HI, the regulator repeats the
start-up procedure, including the soft-start function.
PWM Operation
In the PWM mode, the P channel MOSFET and N channel
MOSFET always operate complementary. When the
PMOSFET is on and the NMOSFET off, the inductor current
increases linearly. The input energy is transferred to the
output and also stored in the inductor. When the P channel
MOSFET is off and the N channel MOSFET on, the inductor
current decreases linearly, and energy is transferred from
the inductor to the output. Hence, the average current
through the inductor is the output current. Since the inductor
and the output capacitor act as a low pass filter, the duty
cycle ratio is approximately equal to VO divided by VIN.
The output LC filter has a second order effect. To maintain
the stability of the converter, the overall controller must be
compensated. This is done with the fixed internally
compensated error amplifier and the PWM compensator.
Because the compensations are fixed, the values of input
and output capacitors are 10µF to 22µF ceramic. The
inductor is nominally 1.8µH, but 1.5µA to 2.2µH can be used.
100% Duty Ratio Operation
EL7536 utilizes CMOS power FET's as the internal
synchronous power switches. The upper switch is a PMOS
and lower switch a NMOS. This not only saves a boot
capacitor, it also allows 100% turn-on of the upper PFET
switch, achieving VO close to VIN. The maximum achievable
VO is,
VO = VIN (RL + RDSON1) × IO
Where RL is the DC resistance on the inductor and RDSON1
the PFET on-resistance, nominal 70mΩ at room temperature
with tempco of 0.2mΩ/°C.
As the input voltage drops gradually close or even below the
preset VO, the converter gets into 100% duty ratio. At this
condition, the upper PFET needs some minimum turn-off
time if it is turned off. This off-time is related to input/output
conditions. This makes the duty ratio appears randomly and
increases the output ripple somewhat until the 100% duty
ratio is reached. Larger output capacitor could reduce the
random-looking ripple. Users need to verify if this condition
has adverse effect on overall circuit if close to 100% duty
ratio is expected.
RSI/POR Function
When powering up, the open-collector Power-On-Reset
output holds low for about 100ms after VO reaches the
preset voltage. When the active-HI reset signal RSI is
issued, POR goes to low immediately and holds for the
same period of time after RSI comes back to LOW. The
output voltage is unaffected. (Please refer to the timing
diagram). When the function is not used, connect RSI to
ground and leave open the pull-up resister R4 at POR pin.
The POR output also serves as a 100ms delayed Power
Good signal when the pull-up resister R4 is installed. The
RSI pin needs to be directly (or indirectly through a resister
R6) connected to Ground for this to function properly.
VO
RSI
POR
100ms
MIN
25ns
100ms
FIGURE 14. RSI & POR TIMING DIAGRAM
Output Voltage Selection
Users can set the output voltage of the converter with a
resister divider, which can be chosen based on the following
formula:
VO
=
0.8
×
1
+
R-R----21- ⎠⎟⎞
Component Selection
Because of the fixed internal compensation, the component
choice is relatively narrow. We recommend 10µF to 22µF
multi-layer ceramic capacitors with X5R or X7R rating for
both the input and output capacitors, and 1.5µH to 2.2µH
inductance for the inductor.
7 FN7396.8
July 13, 2006

7페이지


구       성 총 9 페이지수
다운로드[ EL7536.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
EL7530

Monolithic 600mA Step-Down Regulator

Intersil Corporation
Intersil Corporation
EL7531

Monolithic 1A Step-Down Regulator with Low Quiescent Current

Intersil Corporation
Intersil Corporation

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵