|
|
PDF CS51033 Data sheet ( Hoja de datos )
| Número de pieza | CS51033 | |
| Descripción | Fast P-Ch FET Buck Controller | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CS51033 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
CS51033
Fast P−Ch FET Buck
Controller
The CS51033 is a switching controller for use in DC−DC
converters. It can be used in the buck topology with a minimum
number of external components. The CS51033 consists of a 1.0 A
power driver for controlling the gate of a discrete P−Channel
transistor, fixed frequency oscillator, short circuit protection timer,
programmable Soft−Start, precision reference, fast output voltage
monitoring comparator, and output stage driver logic with latch.
The high frequency oscillator allows the use of small inductors and
output capacitors, minimizing PC board area and systems cost. The
programmable Soft−Start reduces current surges at start up. The short
circuit protection timer significantly reduces the P−Ch FET duty cycle
to approximately 1/30 of its normal cycle during short circuit
conditions.
Features
• 1.0 A Totem Pole Output Driver
• High Speed Oscillator (700 kHz max)
• No Stability Compensation Required
• Lossless Short Circuit Protection
• 2.0% Precision Reference
• Programmable Soft−Start
• Wide Ambient Temperature Range:
♦ Industrial Grade: −40°C to 85°C
♦ Commercial Grade: 0°C to 70°C
• Pb−Free Packages are Available
http://onsemi.com
8
1
SOIC−8
D SUFFIX
CASE 751
MARKING DIAGRAM
8
51033
ALYWx
G
1
51033 = Device Code
A = Assembly Location
L = Wafer Lot
Y = Year
W = Work Week
x = Continuation of Device Code
x = Y or G
G = Pb−Free Package
PIN CONNECTIONS
1
VGATE
PGND
COSC
GND
VC
CS
VCC
VFB
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
© Semiconductor Components Industries, LLC, 2005
October, 2005 − Rev. 10
1
Publication Order Number:
CS51033/D
1 page  
CS51033
CIRCUIT DESCRIPTION
THEORY OF OPERATION
Control Scheme
The CS51033 monitors the output voltage to determine
when to turn on the P−Ch FET. If VFB falls below the internal
reference voltage of 1.25 V during the oscillator’s charge
cycle, the P−Ch FET is turned on and remains on for the
duration of the charge time. The P−Ch FET gets turned off
and remains off during the oscillator’s discharge cycle time
with the maximum duty cycle to 80%. It requires 7.0 mV
typical, and 20 mV maximum ripple on the VFB pin to
operate. This method of control does not require any loop
stability compensation.
Startup
The CS51033 has an externally programmable Soft−Start
feature that allows the output voltage to come up slowly,
preventing voltage overshoot on the output.
At startup, the voltage on all pins is zero. As VCC rises, the
VC voltage along with the internal resistor RG keeps the
P−Ch FET off. As VCC and VC continue to rise, the oscillator
capacitor (COSC ) and the Soft−Start/Fault Timing capacitor
(CS) charges via internal current sources. COSC gets charged
by the current source IC and CS gets charged by the IT source
combination described by:
ǒ ǓICS + IT *
IT
55
)
IT
5
The internal Holdoff Comparator ensures that the external
P−Ch FET is off until VCS > 0.7 V, preventing the GATE
flip−flop (F2) from being set. This allows the oscillator to
reach its operating frequency before enabling the drive
output. Soft−Start is obtained by clamping the VFB
comparator’s (A6) reference input to approximately 1/2 of
the voltage at the CS pin during startup, permitting the
control loop and the output voltage to slowly increase. Once
the CS pin charges above the Holdoff Comparator trip point
of 0.7 V, the low feedback to the VFB Comparator sets the
GATE flip−flop during COSC’s charge cycle. Once the
GATE flip−flop is set, VGATE goes low and turns on the
P−Ch FET. When VCS exceeds 2.4 V, the CS charge sense
comparator (A4) sets the VFB comparator reference to 1.25
V completing the startup cycle.
Lossless Short Circuit Protection
The CS51033 has “lossless” short circuit protection since
there is no current sense resistor required. When the voltage
at the CS pin (the fault timing capacitor voltage ) reaches
2.5 V, the fault timing circuitry is enabled. During normal
operation the CS voltage is 2.6 V. During a short circuit or
a transient condition, the output voltage moves lower and the
voltage at VFB drops. If VFB drops below 1.15 V, the output
of the fault comparator goes high and the CS51033 goes into
a fast discharge mode. The fault timing capacitor, CS,
discharges to 2.4 V. If the VFB voltage is still below 1.15 V
when the CS pin reaches 2.4 V, a valid fault condition has
been detected. The slow discharge comparator output goes
high and enables gate G5 which sets the slow discharge
flip−flop. The VGATE flip−flop resets and the output switch
is turned off. The fault timing capacitor is slowly discharged
to 1.5 V. The CS51033 then enters a normal startup routine.
If the fault is still present when the fault timing capacitor
voltage reaches 2.5 V, the fast and slow discharge cycles
repeat as shown in Figure 3.
If the VFB voltage is above 1.15 V when CS reaches 2.4 V
a fault condition is not detected, normal operation resumes
and CS charges back to 2.6 V. This reduces the chance of
erroneously detecting a load transient as a fault condition.
2.6 V
VCS 2.4 V
1.5 V
0V
S1
TSTART
START
S2 S1
NORMAL OPERATION
S2
S3
S3 S1
S2
S3
S3
td1 tFAULT
tRESTART td2
tFAULT
FAULT
2.5 V
0V
VGATE
1.25 V
1.15 V
VFB
Figure 3. Voltage on Start Capacitor (VGS), the Gate (VGATE), and in the Feedback Loop (VFB),
During Startup, Normal and Fault Conditions
http://onsemi.com
5
5 Page | ||
| Páginas | Total 10 Páginas | |
| PDF Descargar | [ Datasheet CS51033.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CS51031 | Fast PFET Buck Controller Does Not Require Compensation |  Cherry Semiconductor Corporation |
| CS51031 | Fast P-Ch FET Buck Controller | ON Semiconductor |
| CS51033 | Fast PFET Buck Controller Does Not Require Compensation | Cherry Semiconductor Corporation |
| CS51033 | Fast P-Ch FET Buck Controller | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |