Datasheet.kr   

NBSG86ABAEVB 데이터시트 PDF




ON Semiconductor에서 제조한 전자 부품 NBSG86ABAEVB은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 NBSG86ABAEVB 자료 제공

부품번호 NBSG86ABAEVB 기능
기능 Evaluation Board Manual
제조업체 ON Semiconductor
로고 ON Semiconductor 로고


NBSG86ABAEVB 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 20 페이지수

미리보기를 사용할 수 없습니다

NBSG86ABAEVB 데이터시트, 핀배열, 회로
NBSG86ABAEVB
Evaluation Board Manual
for NBSG86A
http://onsemi.com
EVALUATION BOARD MANUAL
DESCRIPTION
This document describes the NBSG86A evaluation board What measurements can you expect to make?
and the appropriate lab test setups. It should be used in
The following measurements can be performed in the
conjunction with the device data sheet, which includes single–ended (Note 1) or differential mode of operation:
specifications and a full description of device operation.
Frequency Performance
The board is used to evaluate the NBSG86A
GigaCommdifferential Smart Gate multi-function logic
gate, which can be configured as an AND/NAND,
OR/NOR, XOR/XNOR, or 2:1 MUX. The OLS input of the
NBSG86A is used to program the peak–to–peak output
amplitude between 0 and 800 mV in five discrete steps.
Output Amplitude (VOH /VOL)
Output Rise and Fall Time
Output Skew
Eye pattern generation
Jitter
The board is implemented in two layers and provides a
high bandwidth 50 W controlled impedance environment for
VIHCMR (Input High Common Mode Range)
higher performance. The first layer or primary trace layer is
5 mils thick Rogers RO6002 material, which is engineered
to have equal electrical length on all signal traces from thewww.DataSheet4U.com
NBSG86A device to the sense output. The second layer is
32 mils thick copper ground plane.
For standard lab setup and test, a split (dual) power supply
is required enabling the 50 W impedance from the scope to NOTE:
be used as termination of the ECL signals, where VTT is the
system ground (VCC = 2.0 V, VTT = VCC - 2.0 V and VEE
is -0.5 V or -1.3 V, see Setup 1).
1. Single- ended meas urements can only be made at
VCC - VEE = 3.3 V using this board setup.
Figure 1. NBSG86A Evaluation Board
© Semiconductor Components Industries, LLC, 2003
March, 2003 - Rev. 0
1
Publication Order Number:
NBSG86ABAEVB/D




NBSG86ABAEVB pdf, 반도체, 판매, 대치품
NBSG86ABAEVB
OR/NOR Function Setup
VTT = 0 V VCC = 2.0 V VTT = 0 VVCC = 2.0 V
GND D1
D1 VCC
Oscilloscope
Signal Generator
OUT
Amplitude = 400 mV
Offset = 660 mV
SEL
Q
Channel 1
OUT
SEL
Channel 2
Q
OUT1
OLS
D0
VEE
D0
OUT1
TRIGGER
OLS*
*See NBSG86A data sheet pg 2.
VEE = -1.3 V (3.3 V op)
or
VEE = -0.5 V (2.5 V op)
TRIGGER
Figure 3. NBSG86A Board Setup - Time Domain (OR/NOR Function)
Step 1:
Connect Power
1a: Connect the following supplies to the evaluation board via surface mount clips.
Power Supply Summary Table
3.3 V Setup
2.5 V Setup
VCC = 2.0 V
VTT = GND
VEE = -1.3 V
VCC = 2.0 V
VTT = GND
VEE = -0.5 V
http://onsemi.com
4

4페이지










NBSG86ABAEVB 전자부품, 판매, 대치품
NBSG86ABAEVB
XOR/XNOR Function Setup (continued)
Step 2:
Connect the Inputs
For Differential Mode (3.3 V and 2.5 V operation)
2a: Connect the differential outputs of the generator to the differential inputs of the device
(OUT OUT to SEL/SEL; OUT1/OUT1 to DO&D1/D0&D1 respectively).
Step 2e: Connect the generator trigger to the oscilloscope trigger.
For Single-Ended Mode (3.3 V operation only)
2a: Connect an AC-coupled output of the generator to the desired differential input of the
device.
2b: Connect the unused differential input of the device to VTT (GND) through a
50 W resistor.
2e: Connect the generator trigger to the oscilloscope trigger.
All Function Setups
Connect OLS (Output Level Select) to the required voltage to obtain desired output ampli-
tude. Refer to the NBSG86A device data sheet page 2 OLS voltage table.
Step 3:
Setup Input Signal
3a: Set the signal generator amplitude to 400 mV. Note that the signal generator amplitude
can vary from 75 mV to 900 mV to produce a 400 mV DUT output.
3b: Set the signal generator offset to 660 mV (the center of a nominal RSECL output). Note
that the VIHCMR (Input High Voltage Common Mode Range) allows the signal generator
offset to vary as long as VIH is within the VIHCMR range. Refer to the device data sheet for
further information.
3c: Set the generator output for a square wave clock signal with a 50% duty cycle, or for a
PRBS data signal.
Step 4:
Connect Output Signals
4a: Connect the outputs of the evaluation board (Q, Q) to the oscilloscope. The oscilloscope
sampling head must have internal 50 W termination to ground.
NOTE: Where a single output is being used, the unconnected output for the pair must be terminated to
VTT through a 50 W resistor for best operation. Unused pairs may be left unconnected. Since
VTT = 0 V, a standard 50 W SMA termination is recommended.
http://onsemi.com
7

7페이지


구       성 총 20 페이지수
다운로드[ NBSG86ABAEVB.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
NBSG86ABAEVB

Evaluation Board Manual

ON Semiconductor
ON Semiconductor

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵