Datasheet.kr   

34017-1P 데이터시트 PDF




Motorola Semiconductors에서 제조한 전자 부품 34017-1P은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 34017-1P 자료 제공

부품번호 34017-1P 기능
기능 MC34017-1P
제조업체 Motorola Semiconductors
로고 Motorola Semiconductors 로고


34017-1P 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 8 페이지수

미리보기를 사용할 수 없습니다

34017-1P 데이터시트, 핀배열, 회로
Telephone Tone Ringer
Bipolar Linear/I2L
Complete Telephone Bell Replacement Circuit with Minimum
External Components
On–Chip Diode Bridge and Transient Protection
Direct Drive for Piezoelectric Transducers
Push Pull Output Stage for Greater Output Power Capability
Base Frequency Options – MC34017–1: 1.0 kHz
– MC34017–2: 2.0 kHz
– MC34017–3: 500 Hz
Input Impedance Signature Meets Bell and EIA Standards
Rejects Rotary Dial Transients
Order this document by MC34017/D
MC34017
TELEPHONE TONE RINGER
BIPOLAR LINEAR/I2L
SEMICONDUCTOR
TECHNICAL DATA
8
1
D SUFFIX
PLASTIC PACKAGE
CASE 751
Typical Application
160 k
5.0 µF
C
25 V
15 k 2.2 µF
3.0 V
876 5
AC2 RG RC RS
Ring
1.0 µF
Tip
6.8 k
MC34017–X
AC1 RO1 RO2
123
RI
4
MC34017–1: C = 1000 pF
MC34017–2: C = 500 pF
MC34017–3: C = 2000 pF
Piezo Sound
Element
This device contains 97 active transistors and 79 gates.
MOTOROLA ANALOG IC DEVICE DATA
8
1
P SUFFIX
PLASTIC PACKAGE
CASE 626
PIN CONNECTIONS
AC1 1
RO1 2
RO2 3
RI 4
8 AC2
7 RG
6 RC
5 RS
(Top View)
ORDERING INFORMATION
Operating
Device Temperature Range
Package
MC34017D
TA = –20° to +60°C
MC34017P
SOIC
Plastic DIP
© Motorola, Inc. 1996
1




34017-1P pdf, 반도체, 판매, 대치품
MC34017
CIRCUIT DESCRIPTION
The MC34017 Tone Ringer derives its power supply by
rectifying the ac ringing signal. It uses this power to activate
a tone generator and drive a piezo–ceramic transducer. The
tone generation circuitry includes a relaxation oscillator and
frequency dividers which produce high and low frequency
tones as well as the tone warble frequency. The relaxation
oscillator frequency fo is set by resistor R2 and capacitor C2
connected to Pin RC. The oscillator will operate with fo from
1.0 kHz to 10 kHz with the proper choice of external
components (see Figure 1).
The frequency of the tone ringer output signal at RO1 and
RO2 alternates between fo/4 to fo/5. The warble rate at which
the frequency changes is fo/320 for the MC34017–1, fo/640
for the MC34017–2 and fo/160 for the MC34017–3. With a
4.0 kHz oscillator frequency, the MC34017–1 produces
800 Hz and 1000 Hz tones with a 12.5 Hz warble rate. The
MC34017–2 generates 1600 Hz and 2000 Hz tones with a
similar 12.5 Hz warble frequency from an 8.0 kHz oscillator
frequency. The MC34017–3 will produce 400 Hz and 500 Hz
tones with a 12.5 Hz warble rate from a 2.0 kHz oscillator
frequency. The tone ringer output circuit can source or sink
20 mA with an output voltage swing of 37 V peak–to–peak.
Volume control is readily implemented by adding a variable
resistance in series with the piezo transducer.
Input signal detection circuitry activates the tone ringer
output when the ac line voltage exceeds programmed
threshold level. Resistor R3 determines the ringing signal
amplitude at which an output signal at RO1 and RO2 will be
generated. The ac ringing signal is rectified by the internal
diode bridge. The rectified input signal produces a voltage
across R3 which is referenced to RG. The voltage across
resistor R3 is filtered by capacitor C3 at the input to the
threshold circuit.
Figure 1. Oscillator Period (1/fo) versus
Oscillator R2 C2 Product
800
600
400
200
0
0
150 k R2 300 k
400 pF C2 3000 pF
100 200 300 400
R2 C2, OSCILLATOR R2 C2 PRODUCT (µs)
500
When the voltage on capacitor C3 exceeds 1.2 V, the
threshold comparator enables the tone ringer output. Line
transients produced by pulse dialing telephones do not charge
capacitor C3 sufficiently to activate the tone ringer output.
Capacitors C1 and C4 and resistor R1 determine the 10 V,
24 Hz signature test impedance. C4 also provides filtering for
the output stage power supply to prevent droop in the square
wave output signal. Six diodes in series with the rectifying
bridge provide the necessary non–linearity for the 2.5 V,
24 Hz signature tests.
An internal shunt voltage regulator between the RI and RG
terminals provides dc voltage to power the output stage,
oscillator and frequency dividers. The dc voltage at RI is
limited to approximately 22 V in regulation. To protect the IC
from telephone line transients, an SCR is triggered when the
regulator current exceeds 50 mA. The SCR diverts current
from the shunt regulator and reduces the power dissipation
within the IC.
EXTERNAL COMPONENTS
R1 Line Input Resistor
R1 affects the tone ringer input impedance. It
also influences ringing threshold voltage and
limits current from line transients.
(Range: 2.0 to 10 k).
C1 Line Input Capacitor
C1 ac couples the tone ringer to the telephone
line and controls ringer input impedance at low
frequencies.
(Range: 0.4 to 2.0 µF).
R2 Oscillator Resistor
(Range: 150 to 300 k).
C2 Oscillator Capacitor
(Range: 400 to 3000 pF).
R3 Input Current Sense Resistor
R3 controls the ringing threshold voltage.
Increasing R3 decreases the ring–start voltage.
(Range: 5.0 to 18 k).
C3 Ringing Threshold Filter Capacitor
C3 filters the ac voltage across R3 at the input
of the ringing threshold comparator. It also
provides dialer transient rejection.
(Range: 0.5 to 5.0 µF).
C4 Ringer Supply Capacitor
C4 filters supply voltage for the tone generating
circuits. It also provides an ac current path for
the 10 Vrms ringer signature impedance.
(Range: 1.0 to 10 µF).
(1/fo = 1.45 R2 C2 + 10 µs)
4 MOTOROLA ANALOG IC DEVICE DATA

4페이지










34017-1P 전자부품, 판매, 대치품
V
I1
MC34017–1: C = 1000 pF*
MC34017–2: C = 500 pF*
MC34017–3: C = 1000 pF*
*Indicates 1% tolerance (5% otherwise)
MC34017
Figure 5. Test Four
1 AC1
2 RO1
AC2 8
RG 7
3 RO2
DUT
6
RC
4 RI RS 5
160 k*
C
15 k*
0.2 µF
a. Set I1 to 30 mA. Measure voltage at Pin 1 (Voff).
b. Set I1 to 100 mA. Measure voltage at Pin 1 (Von).
(Each test < 30 ms)
Figure 6. Test Five
6.8 k*
1 AC1
50 V 2 RO1
AC2 8
RG 7
3 RO2
DUT
6
RC
45
RI RS
MC34017–1: C = 1000 pF*
MC34017–2: C = 500 pF*
MC34017–3: C = 1000 pF*
*Indicates 1% tolerance (5% otherwise)
Figure 7. Test Six
160 k*
C
15 k*
Vclamp
Measure voltage at Pin 5 (Vclamp).
6.8 k*
1 AC1
50 V 2 RO1
AC2 8
RG 7
20 k VO
DUT
6
RC
3 RO2
45
RI RS
160 k*
C
15 k*
2.0 k
S1
VRC
MC34017–1: C = 1000 pF*
MC34017–2: C = 500 pF*
MC34017–3: C = 1000 pF*
*Indicates 1% tolerance (5% otherwise)
0.2 µF
With VRC = 4.0 V, close S1. Measure dc voltage between Pins 2 and 3
(VO1). Repeatedly switch VRC between 4.0 V and 0 V until Pins 2 and 3
change state. Measure the new voltage between Pins 2 and 3 (VO2).
Calculate: VO = |VO1| + |VO2|.
MOTOROLA ANALOG IC DEVICE DATA
7

7페이지


구       성 총 8 페이지수
다운로드[ 34017-1P.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
34017-1P

MC34017-1P

Motorola Semiconductors
Motorola Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵