Datasheet.kr   

AT83C5135 데이터시트 PDF




ATMEL Corporation에서 제조한 전자 부품 AT83C5135은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 AT83C5135 자료 제공

부품번호 AT83C5135 기능
기능 8-bit Microcontroller
제조업체 ATMEL Corporation
로고 ATMEL Corporation 로고


AT83C5135 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 30 페이지수

미리보기를 사용할 수 없습니다

AT83C5135 데이터시트, 핀배열, 회로
Features
80C52X2 Core (6 Clocks per Instruction)
– Maximum Core Frequency 48 MHz in X1 Mode, 24 MHz in X2 Mode
– Dual Data Pointer
– Full-duplex Enhanced UART (EUART), TxD and Rxd are 5 Volt Tolerant
– Three 16-bit Timer/Counters: T0, T1 and T2
– 256 Bytes of Scratchpad RAM
8/16/32-Kbyte On-chip ROM
512 byte or 32-Kbyte EEPROM(1)
On-chip Expanded RAM (ERAM): 1024 Bytes
Integrated Power Monitor (POR/PFD) to Supervise Internal Power Supply
USB 2.0 Full Speed Compliant Module with Interrupt on Transfer Completion (12Mbps)
– Endpoint 0 for Control Transfers: 32-byte FIFO
– 6 Programmable Endpoints with In or Out Directions and with Bulk, Interrupt or
Isochronous Transfers
• Endpoint 1, 2, 3: 32-byte FIFO
• Endpoint 4, 5: 2 x 64-byte FIFO with Double Buffering (Ping-pong Mode)
– Suspend/Resume Interrupts
– Power-on Reset and USB Bus Reset
– 48 MHz DPLL for Full-speed Bus Operation
– USB Bus Disconnection on Microcontroller Request
5 Channels Programmable Counter Array (PCA) with 16-bit Counter, High-speed
Output, Compare/Capture, PWM and Watchdog Timer Capabilities
Programmable Hardware Watchdog Timer (One-time Enabled with Reset-out): 50 ms to
6s at 4 MHz
Keyboard Interrupt Interface on Port P1 (8 Bits)
TWI (Two Wire Interface) 400Kbit/s
SPI Interface (Master/Slave Mode) MISO,MOSI,SCK and SS are 5 Volt Tolerant
34 I/O Pins
4 Direct-drive LED Outputs with Programmable Current Sources: 2-6-10 mA Typical
4-level Priority Interrupt System (11 sources)
Idle and Power-down Modes
0 to 32 MHz On-chip Oscillator with Analog PLL for 48 MHz Synthesis
Industrial Temperature Range
Low Voltage Range Supply: 2.7V to 3.6V
Packages: Die SO28, QFN32, MLF48, TQFP64
8-bit
Microcontroller
with Full Speed
USB Device
AT83C5134
AT83C5135
AT83C5136
Notes: 1. EEPROM only available on MLF48
1. Description
AT83C5134/35/36 are high performance ROM versions
of the 80C51 single-chip 8-bit microcontrollers with full
speed USB functions.
AT83C5134/35 is pin compatible with AT89C5130A 16-
Kbytes In-System Programmable Flash microcontrollers.




AT83C5135 pdf, 반도체, 판매, 대치품
4. Pinout Description
4.1 Pinout
Figure 4-1. AT83C5134/35/36 64-pin VQFP Pinout
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
NC
P2.3/A11
P2.4/A12
P2.5/A13
XTAL2
XTAL1
P2.6/A14
P2.7/A15
VDD
AVDD
NC
AVSS
NC
P3.0/RxD
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
VQFP64
48 NC
47 NC
46 P0.1/AD1
45 P0.2/AD2
44 RST
43 P0.3/AD3
42 VSS
41 NC
40 P0.4/AD4
39 P3.7/RD/LED3
38 P0.5/AD5
37 P0.6/AD6
36 P0.7/AD7
35 P3.6/WR/LED2
34 NC
33 NC
17 18 19 20 21 22 23 24 25 26 27 28 29 30 3132
4 AT83C5134/35/36
7683C–USB–11/07

4페이지










AT83C5135 전자부품, 판매, 대치품
AT83C5134/35/36
Table 4-3. Serial I/O Signal Description
Signal
Name
RxD
TxD
Type Description
Serial Input
I
The serial input for Extended UART. This I/O is 5 Volt Tolerant.
O
Serial Output
The serial output for Extended UART. This I/O is 5 Volt Tolerant.
Alternate
Function
P3.0
P3.1
Table 4-4. Timer 0, Timer 1 and Timer 2 Signal Description
Signal
Name
Type Description
Alternate
Function
INT0
Timer 0 Gate Input
INT0 serves as external run control for timer 0, when selected by GATE0 bit in
TCON register.
I External Interrupt 0
INT0 input set IE0 in the TCON register. If bit IT0 in this register is set, bits IE0 are
set by a falling edge on INT0. If bit IT0 is cleared, bits IE0 is set by a low level on
INT0.
P3.2
INT1
Timer 1 Gate Input
INT1 serves as external run control for Timer 1, when selected by GATE1 bit in
TCON register.
I External Interrupt 1
INT1 input set IE1 in the TCON register. If bit IT1 in this register is set, bits IE1 are
set by a falling edge on INT1. If bit IT1 is cleared, bits IE1 is set by a low level on
INT1.
P3.3
Timer Counter 0 External Clock Input
T0
I When Timer 0 operates as a counter, a falling edge on the T0 pin increments the
P3.4
count.
Timer/Counter 1 External Clock Input
T1
I When Timer 1 operates as a counter, a falling edge on the T1 pin increments the
P3.5
count.
I Timer/Counter 2 External Clock Input
T2
O Timer/Counter 2 Clock Output
P1.0
T2EX
I Timer/Counter 2 Reload/Capture/Direction Control Input
P1.1
Table 4-5. LED Signal Description
Signal
Name
Type Description
LED[3:0]
Direct Drive LED Output
These pins can be directly connected to the Cathode of standard LEDs without
O external current limiting resistors. The typical current of each output can be
programmed by software to 2, 6 or 10 mA. Several outputs can be connected
together to get higher drive capabilities.
Alternate
Function
P3.3
P3.5
P3.6
P3.7
7683C–USB–11/07
7

7페이지


구       성 총 30 페이지수
다운로드[ AT83C5135.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
AT83C5132

(AT83C5132 / AT89C5132) Usb C51-based Microcontroller

ATMEL Corporation
ATMEL Corporation
AT83C5134

8-bit Microcontroller

ATMEL Corporation
ATMEL Corporation

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵