|
|
|
부품번호 | EK01 기능 |
|
|
기능 | EVALUATION KIT | ||
제조업체 | Apex Microtechnology | ||
로고 | |||
전체 4 페이지수
���������������
�������������������������������
����
��������������������������������������������������������������
INTRODUCTION
This easy-to-use kit provides a platform for the evaluation of
PWM amplifiers using the SA01 pin-out configuration. It can be
used to analyze a multitude of standard or proprietary circuit
configurations, and is flexible enough to do most standard
amplifier test configurations. The board is designed for surface
mounting all components except the switching amplifier.
The schematic is shown in Figure 2. Note that all of the
components shown on the schematic will probably not be used
for any single circuit. Some components will simply be omitted,
while others require installation of a jumper to complete the
signal path.
Only components unique to the EK01 are provided in this kit.
Hardware similar to that shown in figure 1 must be obtained lo-
cally. The PC board and the foot print of the heatsink measure
3" by 5".
PARTS LIST
Part #
HS16
MS04
EVAL07
60SPG00001
TW10
Description
Heatsink
PC mount Cage Jacks
PC Board
Spacer Grommets
Thermal Washer
Quantity
1
1 Bag/12 each
1
4
1 Box/10 each
ASSEMBLY
1. From the non-silk screen side, insert and solder cage jacks.
Be sure each one is fully seated.
2. From the non-silk screen side, push spacer grommets into
PC board until fully seated. Grommets will snug when screws
are inserted for heatsink mounting.
3. Apply TW10 thermal washer or a thin, even coat of thermal
grease to the bottom of the SA01. If grease is from a tube
make sure there is no sign separation of solids and liquids.
If from a jar, stir it prior to application.
4. Use #14 sleeving to insulate and align at least 2 opposite
pins of the amplifier.
5. Mount amplifier to heatsink using #6 screws and nuts. Do
not over torque.
6. Install components as needed. External connections may be
soldered directly or standard banana jacks may be soldered
to these pads.
7. Insert amplifier pins into cage jacks and fasten board to
heatsink.
BEFORE YOU GET STARTED
* All Apex amplifiers should be handled using proper ESD precautions.
* Always use the heatsink included in this kit with thermal grease.
* Torque the part to the specified 8 to 10 in-lbs (.9 to 1.13 N*M)
* Always use adequate power supply bypassing.
* Do not change connections while the circuit is powered.
* Initially set all power supplies to the minimum operating levels allowed in the device data sheet.
* Check for oscillations.
��������������������������
���������
������������������
��������������
��������������������
����������������������
��������������������������
FIGURE 1.
��������������������������������
��������
�������������������
���������������������
APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL [email protected]1
EK01
COMMON
CONFIGURATIONS
VOLTAGE CONTROL
���
��
���
���
��
��
�� ���
����������������
��
��
��
��
��
���
�
�
����
���
���
��
��
�� �
���
��
���
���
�
���
���
�
���
�
�
���
����
��
��
��
�����
������
��
������
�
��
�
���
�
���
�
��
���
�� ��
��� ��� ���
��
���
��
����
����
���
����
���
POSITION CONTROL
�����
��������
���
���
���
���
��
��
���
�� ��
��
�� ���
��
��
���
�
�
����
���
��
�� �
���
��
�
���
��
���
�
���
�
�
���
����
��
�����
������
��
������
�
��
�
���
�
���
�
��
���
��
��
���
��
����
�
����
���
����
���
����
����
SPEED CONTROL
�����
��������
���
���
���
���
��
��
��
���
��
��
��
��
�� ���
��
��
���
�
�
����
���
��
�� �
���
��
�
���
��
���
�
���
�
�
���
����
��
�����
������
��
������
�
��
�
���
�
���
�
��
���
��
��
���
��
����
�
����
���
�
����
���
AThPisEdXatMa sIhCeRetOhTaEsCbHeeNnOcLarOefGuYlly CchOeRckPeOdRanAdTIisObNelie•ve5d9to80be NreOliaRbTleH, hoSwHeAveNr,NnOo NrespRoOnAsibDili•ty iTsUaCssSuOmNed, foArRpIoZssOibNleAin8ac5cu7r4ac1ies•orUoSmAiss•ionAs.PAPllLsIpCeAciTfiIcOatNioSns HarOe TsuLbIjNecEt:to1ch(a8ng0e0w)ith5o4u6t -n2ot7ic3e.9
4 EK01U REV E DECEMBER 2004 © 2004 Apex Microtechnology Corp.
4페이지 | |||
구 성 | 총 4 페이지수 | ||
다운로드 | [ EK01.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
EK01 | EVALUATION KIT | Apex Microtechnology |
EK02 | Schottky Barrier Diodes 20V | Sanken electric |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |