Datasheet.kr   

BD3985FV PDF 데이터시트 : 부품 기능 및 핀배열

부품번호 BD3985FV
기능 Positive and Negative Variable Linear Regulator
제조업체 Rohm
로고 Rohm 로고 



전체 5 페이지

		

No Preview Available !

BD3985FV 데이터시트, 핀배열, 회로
STRUCTURE
Silicon Monolithic Integrated Circuit
TYPE
Positive and Negative Variable Linear Regulator
PRODUCT SERIES
BD3985FV
FEATURES
1. Built-in positive (REG1) and negative (REG2) Linear Regulator for CCDs/ Variable output/
Low saturation voltage type.
2. Built-in Discharge circuit. Negative output voltage (REG2) turns off immediately,
after STB turns off.
○ABSOLUTE MAXIMUM RATINGS (Ta=25℃)
Parameter
Symbol
Limit
Unit
Positive Supply Voltage
VCC
+18 ※1
V
Negative Supply Voltage
VEE
-18 ※1
V
Power Dissipation
Pd
380 ※2
mW
Operating Temperature Range
Topr
-40~+85
Storage Temperature Range
Tstg
-55~+125
Maximum Junction Temperature
Tjmax
125
※1 Not to exceed Pd.
※2 Reduced by 3.8mW/℃ over Ta=25℃ ,during IC without heat sink operation.
○OPERATING CONDITIONS
Parameter
Symbol
Min
Max Unit
Positive Supply Voltage
VCC
+6.0
+18.0
V
Negative Supply Voltage
VEE
-14.0
-6.0
V
REG1 Output Voltage
Vo1
+5.0
+16.0
V
REG2 Output Voltage
Vo2
-8.5
-5.0
V
Output Current 1 Io1 - 25 mA
Output Current 2 Io2 - 50 mA
※ Vdropout(Reg1) × Io(Reg1) + Vdropout(Reg2) × Io(Reg2) not to exceed Pd=380mW.
1/4
REV. B




BD3985FV pdf, 반도체, 판매, 대치품
4/4
The formation of parasitic elements as a result of the relationships of the potentials of different pins is an inevitable
result of the IC's architecture. The operation of parasitic elements can cause interference with circuit operation as well
as IC malfunction and damage. For these reasons, it is necessary to use caution so that the IC is not used in a way that
will trigger the operation of parasitic elements, such as by the application of voltages lower than the VEE (P substrate)
voltage to input pins. Keep in mind that the IC may malfunction in strong magnetic fields.
(Pin A)
Resistor
Transistor (NPN)
B
(Pin B) C
E
(Pin B)
BC
P+
N
P
P
N
P+
N
Parasitic elements
P+
N
N
P
N
P+
N
P substrate
VEE VEE
Parasitic elements
or Transistors
(Pin A)
E
VEE
Parasitic elements or
Transistors
Parasitic elements
8) Ground patterns
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns, placing
a single ground point at the application's reference point so that the pattern wiring resistance and voltage variations
caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring
pattern of any external parts, either.
9) Applications or inspection processes where the potentials of the VCC pin and other pins may be reversed from their normal
states may cause damage to the IC's internal circuitry or elements. Use an output pin capacitance of 1,000μF or lower
in case VCC is shorted with the GND pin while the external capacitor is charged. It is recommended to insert a diode for
preventing back current flow in series with VCC or bypass diodes between VCC and each pin.
Back current prevention diode
Bypass diode
VCC Pin
10) Thermal shutdown circuit (TSD)
This IC incorporates a built-in TSD circuit for the protection from thermal destruction. The IC should be used within the
specified power dissipation range. However, in the event that the IC continues to be operated in excess of its power dissipation
limits, the attendant rise in the junction temperature (Tj) will trigger the TSD circuit to turn off all output power elements.
The circuit automatically resets once the junction temperature (Tj) drops. Operation of the TSD circuit presumes that the
IC's absolute maximum ratings have been exceeded. Application designs should never make use of the TSD circuit.
11) Overcurrent protection circuit (OCP)
The IC incorporates a built-in overcurrent protection circuit that operates according to the output current capacity. This
circuit serves to protect the IC from damage when the load is shorted. The protection circuit is designed to limit current
flow by not latching in the event of a large and instantaneous current flow originating from a large capacitor or other
component. This protection circuits is effective in preventing damage due to sudden and unexpected accidents. However,
the IC should not be used in applications characterized by the continuous operation or transitioning of the protection
circuits. At the time of thermal designing, keep in mind that the current capacity has negative characteristics to
temperatures.
REV. B

4페이지













구       성총 5 페이지
다운로드[ BD3985FV.PDF 데이터시트 ]
구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

휴대전화 : 010-3582-2743


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877, [ 홈페이지 ]



링크공유

링크 :

관련 데이터시트

부품번호상세설명 및 기능제조사
BD3985FV

Positive and Negative Variable Linear Regulator

Rohm
Rohm

DataSheet.kr    |   2019   |  연락처   |  링크모음   |   검색  |   사이트맵