Datasheet.kr   

V048K060M040 PDF 데이터시트 : 부품 기능 및 핀배열

부품번호 V048K060M040
기능 (V048x060x040) Voltage Transformation Module
제조업체 Vicor Corporation
로고 Vicor Corporation 로고 


전체 15 페이지

		

No Preview Available !

V048K060M040 데이터시트, 핀배열, 회로
www.DataSheet4U.com
VTM
PRELIMINARY
V•I ChipTM – VTM
Voltage Transformation Module
• 48 V to 6 V V•I Chip Converter
• 40.0 A (60.0 A for 1 ms)
• High density – 974 W/in3
• Small footprint – 220 W/in2
• Low weight – 0.5 oz (14 g)
• Pick & Place / SMD
• 125°C operation
• 1 µs transient response
• 3.5 million hours MTBF
• Typical efficiency 95%
• No output filtering required
• Surface mount BGA or J-Lead
packages
V048K060T040
K indicates BGA configuration. For other
mounting options see Part Numbering below.
©
Vf = 26 - 55 V
VOUT = 3.25 - 6.87 V
IOUT = 40.0 A
K = 1/8
ROUT = 7.5 mmax
Actual size
Product Description
The V048K060T040 V•I Chip Voltage Transformation
Module (VTM) excels at speed, density and efficiency to
meet the demands of advanced DSP, FPGA, and ASIC at
the point of load (POL) while providing isolation from
input to output. It achieves a response time of less than
1 µs and delivers up to 40.0 A in a volume of less than
0.25 in3 with unprecedented efficiency. It may be
paralleled to deliver hundreds of amps at an output
voltage settable from 3.25 to 6.87 Vdc.
The VTM V048K060T040’s nominal output voltage is
6 Vdc from a 48 Vdc input Factorized Bus, Vf, and is
controllable from 3.25 to 6.87 Vdc at no load, and from
2.95 to 6.60 Vdc at full load, over a Vf input range of
26 to 55 Vdc. It can be operated either open- or closed-
loop depending on the output regulation needs of the
application. Operating open-loop, the output voltage
tracks its Vf input voltage with a transformation ratio,
K = 1/8 , for applications requiring a programmable
output voltage at high current and high efficiency.
Closing the loop back to an input Pre-Regulation Module
(PRM) or DC-DC converter enables tight load regulation.
The 6 V VTM achieves a power density of 974 W/in3 in a
V•I Chip package compatible with standard pick-and-
place and surface mount assembly processes. The
V•I Chip BGA package supports in-board mounting with
a low profile of 0.16" (4 mm) over the board. A J-lead
package option supports on-board surface mounting
with a profile of only 0.25" (6 mm) over the board. The
VTM’s fast dynamic response and low noise eliminate the
need for bulk capacitance at the load, substantially
increasing the POL density while improving reliability and
decreasing cost.
Absolute Maximum Ratings
Parameter
+In to -In
+In to -In
PC to -In
VC to -In
+Out to -Out
Isolation voltage
Output current
Peak output current
Output power
Peak output power
Case temperature
Operating junction temperature(1)
Values
-1.0 to 60
100
-0.3 to 7.0
-0.3 to 19.0
-0.1 to 15.0
2,250
40.0
60.0
240
360
208
-40 to 125
-55 to 125
Storage temperature
-40 to 150
-65 to 150
Unit
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
A
A
W
W
°C
°C
°C
°C
°C
Notes
For 100 ms
Input to Output
Continuous
For 1 ms
Continuous
For 1 ms
During reflow
T - Grade
M - Grade
T - Grade
M - Grade
Note:
(1) The referenced junction is defined as the semiconductor having the highest temperature.
This temperature is monitored by a shutdown comparator.
Part Numbering
V 048
Voltage
Transformation
Module
Input Voltage
Designator
K
Configuration Options
F = On-board (Figure 15)
K = In-board (Figure 14)
060
Output Voltage
Designator
(=VOUT x10)
T
040
Output Current
Designator
(=IOUT)
Product Grade Temperatures (°C)
Grade Storage Operating
T -40 to150 -40 to125
M -65 to150 -55 to125
vicorpower.com 800-735-6200
V•I Chip Voltage Transformation Module
V048K060T040
Rev. 1.0
Page 1 of 15




V048K060M040 pdf, 반도체, 판매, 대치품
Electrical Specifications (continued)
PRELIMINARY
V•I Chip Voltage Transformation Module
Figure 7— 0-40.0 A step load change with 100 µF input capacitance and
no output capacitance.
Figure 8— 40.0-0 A step load change with 100 µF input capacitance and
no output capacitance.
General
Parameter
MTBF
MIL-HDBK-217F
Isolation specifications
Voltage
Capacitance
Resistance
Agency approvals (pending)
Mechanical parameters
Weight
Dimensions(BGA version)
Length
Width
Height
Min Typ Max
3.5
2,250
10
3,000
cTÜVus
CE Mark
0.5 / 14.0
1.26 / 32
0.85 / 21.5
0.23 / 5.9
Unit
Mhrs
Vdc
pF
M
oz / g
in / mm
in / mm
in / mm
Note
25°C, GB
Input to Output
Input to Output
Input to Output
UL/CSA 60950, EN 60950
Low voltage directive
See Mechanical Drawing, Figures 10 and 12
Auxiliary Pins (Conditions are at 48 Vin, full load, and 25°C ambient unless otherwise specified)
Parameter
Primary Control (PC)
DC voltage
Module disable voltage
Module enable voltage
Current limit
Disable delay time
VTM Control (VC)
External boost voltage
External boost duration
Min Typ Max Unit
4.8 5.0 5.2 Vdc
2.4 2.5
Vdc
2.5 2.6 Vdc
2.4 2.5 2.9 mA
10 µs
12.0 14.0 19.0
10
Vdc
ms
Note
VC voltage must be applied when module is enabled using PC
Source only
PC low to Vout low
Required for VTM start up without PRM
Vin > 26 Vdc. VC must be applied continuously
if Vin < 26 Vdc.
vicorpower.com 800-735-6200
V•I Chip Voltage Transformation Module
V048K060T040
Rev. 1.0
Page 4 of 15

4페이지










V048K060M040 전자부품, 판매, 대치품
Mechanical Drawings
PRELIMINARY
SOLDER BALL
#A1 INDICATOR
21,5
0.85
1,00 18,00 1,00
0.039
0.709
0.039
5,9
0.23
(106) X
Ø
0.020
0.51
SOLDER
BALL
9,00
0.354
SOLDER BALL #A1
1,00 TYP
0.039
30,00
1.181
32,0 28,8
1.26
1.13
CL
16,0
0.63
15,00
0.591
TOP VIEW (COMPONENT SIDE)
1,6
0.06
CL
BOTTOM VIEW
1,00
0.039
3,9
0.15
15,6
0.62
SEATING PLANE
Figure 10— V T M BGA mechanical outline; Inboard mounting
NOTES:
mm
1- DIMENSIONS ARE inch .
2- UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE:
.X/[.XX] = +/-0.25/[.01]; .XX/[.XXX] = +/-0.13/[.005]
3- PRODUCT MARKING ON TOP SURFACE
IN-BOARD MOUNTING
BGA surface mounting requires a
cutout in the PCB in which to recess the V•I Chip
(
ø
0,51
0.020
)
SOLDER MASK
DEFINED PADS
0,50
0.020
1,50
0.059
(01.,00309)
ø
0,53
0.021
PLATED
VIA
CONNECT TO
INNER LAYERS
0,50
0.020
1,00
0.039
SOLDER PAD #A1
18,00
0.709
9,00
0.354
(2)
X
10,00
0.394
1,00
0.039
1
(4)
X
6,00
0.236
20,00
0.787 17,00
0.669
15,00
0.591
13,00
0.512
(106) X
ø
0,51
0.020
SOLDER MASK
DEFINED PAD
PCB CUTOUT
8,08
0.318
16,16
0.636
24,00
0.945
16,00
0.630
8,00
0.315
29,26
1.152
31
0,37
0.015
(4)
X
R
1,6
0.06
Figure 11— VTM BGA PCB land/VIA layout information; Inboard mounting
1,00
0.039
(01.,00309)
RECOMMENDED LAND AND VIA PATTERN
(COMPONENT SIDE SHOWN)
NOTES:
mm
1- DIMENSIONS ARE inch .
2- UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE:
.X/[.XX] = +/-0.25/[.01]; .XX/[.XXX] = +/-0.13/[.005]
vicorpower.com 800-735-6200
V•I Chip Voltage Transformation Module
V048K060T040
Rev. 1.0
Page 7 of 15

7페이지



구       성총 15 페이지
다운로드[ V048K060M040.PDF 데이터시트 ]
구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

휴대전화 : 010-3582-2743


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877, [ 홈페이지 ]



링크공유

링크 :

관련 데이터시트

부품번호상세설명 및 기능제조사
V048K060M040

(V048x060x040) Voltage Transformation Module

Vicor Corporation
Vicor Corporation

추천 데이터시트

부품번호상세설명 및 기능제조사
CQ1565RT

FSCQ1565RT, Green Mode Fairchild Power Switch. In general, a Quasi-Resonant Converter (QRC) shows lower EMI and higher power conversion efficiency compared to conventional hard-switched converter with a fixed switching frequency.

Fairchild
Fairchild
KF16N25D

MOSFET의 기능은 N Channel MOS Field effect transistor입니다. This planar stripe MOSFET has better characteristics, such as fast switching time, low on resistance, low gate charge and excellent avalanche characteristics. It is mainly suitable for DC/DC Converters and switching mode power supplies.( Vdss=250V, Id=13A )

KEC
KEC

DataSheet.kr    |   2018   |  연락처   |  링크모음   |   검색  |   사이트맵