Datasheet.kr   

AX1117 데이터시트 PDF




Avantics에서 제조한 전자 부품 AX1117은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 AX1117 자료 제공

부품번호 AX1117 기능
기능 1.2A Low Dropout Positive Voltage Regulator
제조업체 Avantics
로고 Avantics 로고


AX1117 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 7 페이지수

미리보기를 사용할 수 없습니다

AX1117 데이터시트, 핀배열, 회로
www.DataSheet4U.com
Page No. : 1/7
AX1117 Series
1.2A Low Dropout Positive Voltage Regulator
Features
Low Dropout Voltage 1.2V at 1.2A
Adjustable or Fixed Voltage (1.8V, 2.5V, 3.3V, 5V)
Over Current Protection
Thermal Overload Protection
Maximum Line Regulation 0.45%
Maximum Load Regulation 0.4%
Adjust Pin Current Less Than 90 uA
Applications
SCSI-2 Active Termination
High Efficiency Linear Regulators
5V to 3.3V Voltage Converter
Battery Charger
Battery Management Circuits For Notebook And Palmtop PCs
Core Voltage Supply: FPGA, PLD, DSP, CPU
General Description
AX1117 Series Pin Assignment
123
Tab
123
3-Lead Plastic SOT-89
Package Code: M
Pin 1: ADJ/GND
Pin 2: VOUT
Pin 3: VIN
3-Lead Plastic SOT-223
Package Code: SJ
Pin 1: ADJ/GND
Pin 2 & Tab: VOUT
Pin 3: VIN
Tab
Tab
123
3-Lead Plastic TO-252
Package Code: J
Pin 1: ADJ/GND
Pin 2 & Tab: VOUT
Pin 3: VIN
3-Lead Plastic TO-220AB
Package Code: E
Pin 1: ADJ/GND
Pin 2 & Tab: VOUT
Pin 3: VIN
1 23
The AX1117 Series are available in fixed and adjustable output voltage versions. Over current and thermal overload protection
are integrated onto the chip. Output current will decrease while it reaches the preset current or temperature limit. The dropout
voltage is specified at 1.2V Maximum at full rated output current. AX1117 Series provide excellent regulation over variations due
to changes in line, load and temperature. AX1117 Series are three terminal regulators and available in popular packages.
Device Selection Guide
Device
AX1117M-Adj
AX1117M-Fix
AX1117SJ-Adj
AX1117SJ-Fix
Output Voltage
1.3V to 4V
1.8V, 2.5V, 3.3V, 5V
1.3V to 4V
1.8V, 2.5V, 3.3V, 5V
Package
SOT-89
SOT-223
Device
AX1117J-Adj
AX1117J-Fix
AX1117E-Adj
AX1117E-Fix
Output Voltage
1.3V to 4V
1.8V, 2.5V, 3.3V, 5V
1.3V to 4V
1.8V, 2.5V, 3.3V, 5V
Package
TO-252
TO-220AB
Absolute Maximum Ratings
Parameter
Symbol
Input Voltage
Power Dissipation
Operating Junction Temperature Range
Storage Temperature Range
Lead Temperature (Soldering) 5 Sec
Electrostatic Discharge Sensitivity
VIN
PD
TOPR
TSTG
TLEAD
*: SOT-223: 0.9W(Max.), SOT-89: 0.6W(Max.), TO-252: 0.9W(Max.), TO-220: 2.1W(Max.)
Maximum
20
Internally Limited *
0 To +125
-65 To +150
260
2
Units
V
W
°C
°C
°C
KV/Min
AVANTICS - AX1117 Series
Specification No.: 050309-FE0005




AX1117 pdf, 반도체, 판매, 대치품
Page No. : 4/7
Applications Description
Output Voltage Adjustment
Like most regulators, AX1117 series regulate the output by
comparing the output voltage to an internally generated reference
voltage. On the adjustable version, the VREF is available externally as
1.25V between VOUT and ADJ. The voltage ratio formed by R1 and R2
should be set to conduct 10mA (minimum output load). The output
voltage is given by the following equation: VOUT =VREF (1+R2/R1) + IADJ
R2
On fixed versions of AX1117 series, the voltage divider is provided
internally.
Thermal Protection
V IN
In Out
ADJ
IADJ
10uA
V REF
V OUT
R1
R2
AX1117 series have thermal protection which limits junction
temperature to 150°C. However, device functionality is only
guaranteed to a maximum junction temperature of +125°C.
The power dissipation and junction temperature for AX1117 in all
packages given by
PD=(VIN - VOUT) IOUT, TJUNCTION=TAMBIENT+(PDxθJA), Note: TJUNCTION must
not exceed 125°C
VOUT =VREF (1+R2/R1) + IADJ R2
Current Limit Protection
AX1117 series are protected against overload conditions. Current protection is triggered at typically 1.5A.
Stability And Load Regulation
AX1117 series require a capacitor from VOUT to GND to provide
compensation feedback to the internal gain stage. This is to ensure
stability at the output terminal. Typically, a 10uF tantalum or 50uF
aluminum electrolytic is sufficient.
Note : It is important that the ESR for this capacitor does not exceed
0.5.
The output capacitor does not have a theoretical upper limit and
increasing its value will increase stability. COUT = 100 uF or more is
typical for high current regulator design.
AX1117 series load regulation are limited by the resistance of the
wire connecting it to the load(RP). For the adjustable version, the best
load regulation is accomplished when the top of the resistor divider(R1)
is connected directly to the output pin of the AX1117 series. When so
connected, RP is not multiplied by the divider ratio. For fixed output
versions, the top of R1 is internally connected to the output and
ground pin can be connected to low side of the load as a negative
side sense if, so desired.
RP
Parasitic
Line Resistance
In Out
V IN Adj
R1
Connect
R1 to Case
R2
Connect
R2 to Load
RL
Thermal Consideration
The AX1117 series contain thermal limiting circuitry designed to protect itself for over-temperature conditions. Even for normal load
conditions, maximum junction temperature ratings must not be exceeded. As mention in thermal protection section, we need to
consider all sources of thermal resistance between junction and ambient. It contains junction-to-case, case-to-heat-sink interface and
heat sink resistance itself. An additional heat sink is applied externally sometimes. It can increase the maximum power dissipation. For
example, the equivalent junction temperature of 300mA output current is 115°C without external heat sink. Under the same junction
temperature IC can operates 500mA with an adequate heat sink. Therefore, to attach an extra heat sink is recommended.
Junction-to-case thermal resistance is specified from the IC junction to the bottom of the case directly below the die. The bonding
wires are appending paths. The former is the lowest resistance path. Proper mounting is required to ensure the best possible thermal
flow this area of the package to the heat sink. Thermal compound at the case-to-heat-sink interface is strongly recommended. The
case of all devices in this series is electrically connected to the output. Therefore, if the case of the device must be electrically isolated,
a thermally conductive spacer can be used, as long its thermal resistance is considered.
Protection Diode
(The figure is shown as Regulator with Reverse Diode Protection in advanced applications)
In general operation, AX1117 series don’t need any protection diodes. From the cross-section structure of AX1117 sries, the output
pin is connected to P+ substrate, and the input pin is connected to N- well. There is a parasitic reverse diode between them. It can
handle microsecond surge currents of 5A to 10A. Even with large output capacitance, it is very difficult to get those values of surge
currents in normal operation. Only with high value output capacitors, such as 1000uF. And with the input pin instantaneously shorted to
ground. can damage occur. A crowbar circuit at the input of the AX1117 series can generate those kinds of currents, and a diode from
output to input is recommended. Normal power supply cycling or even plugging and unplugging in the system will not generate
currents large enough to do any damage.
AVANTICS - AX1117 Series
Specification No.: 050309-FE0005

4페이지










AX1117 전자부품, 판매, 대치품
Soldering Methods for AVANTICS’s Products
1. Storage environment: Temperature=10oC~35oC Humidity=65%±15%
2. Reflow soldering of surface-mount devices
Figure 1: Temperature profile
TP
Ramp-up
tP
TL
Tsmax
tL
Tsmin
tS
Preheat
Ramp-down
25
t 25oC to Peak
Time
Profile Feature
Average ramp-up rate (TL to TP)
Preheat
- Temperature Min (Tsmin)
- Temperature Max (Tsmax)
- Time (min to max) (ts)
Tsmax to TL
- Ramp-up Rate
Time maintained above:
- Temperature (TL)
- Time (tL)
Peak Temperature (TP)
Time within 5oC of actual Peak
Temperature (tP)
Ramp-down Rate
Time 25oC to Peak Temperature
3. Flow (wave) soldering (solder dipping)
Products
Pb devices.
Pb-Free devices.
Sn-Pb Eutectic Assembly
<3oC/sec
100oC
150oC
60~120 sec
<3oC/sec
183oC
60~150 sec
240oC +0/-5oC
10~30 sec
<6oC/sec
<6 minutes
Peak temperature
245oC ±5oC
260oC +0/-5oC
Page No. : 7/7
Critical Zone
TL to TP
Pb-Free Assembly
<3oC/sec
150oC
200oC
60~180 sec
<3oC/sec
217oC
60~150 sec
260oC +0/-5oC
20~40 sec
<6oC/sec
<8 minutes
Dipping time
5sec ±1sec
5sec ±1sec
AVANTICS - AX1117 Series
Specification No.: 050309-FE0005

7페이지


구       성 총 7 페이지수
다운로드[ AX1117.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
AX1110

350mA Low Dropout Linear Regulator

AXElite
AXElite
AX1112

1.2V 350mA Low Dropout Linear Regulator

AXElite
AXElite

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵