|
|
PDF SPZB260 Data sheet ( Hoja de datos )
| Número de pieza | SPZB260 | |
| Descripción | Wireless Communication & Connectivity ICs and Modules | |
| Fabricantes | ST Microelectronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SPZB260 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
SPZB260
ZigBee module
Features
■ Integrated 2.4GHz ,IEEE 802,15,4-compliant
transceiver:
– 0 dBm nominal TX output power
– -92 dBm RX sensitivity
– + 2 dBm in boost mode
– RX filtering for co-existence with IEEE
802.11g and Bluetooth devices
– Integrated VCO and loop filter
■ IntegratedIEEE802.15.4PHYandMAC
■ Controlled by a Standard Serial Line for an
easy interface of host microcontrollers (SPI)
■ Embedded flash and integrated RAM for
program and data storage
■ On board 24 MHz stable Xtal
■ Integrated RC oscillator ( typ 10KHz) for low
power operation
■ 1 µA power consumption in Deep sleep mode
■ Watchdog timer and power on reset
■ Pins available for Non-intrusive debug
interface (SIF)
■ Single supply voltage 2.1 to 3.6 Vdc.
■ Available Link and Activity outputs for external
■ Indication / monitor
■ CE compliant
■ FCC compliant ( FCC ID:S9NZB260A )
Applications
■ Industrial controls
■ Sensor networking
■ Monitoring of remote systems
■ Home applications
■ Security systems
■ Lighting controls
Description
SPZB260 is a low power consumption ZigBee
module optimized for embedded applications. It
enables OEMs to easily add wireless capability to
electronic devices.
The module is based on SN260 ZigBee Network
Processor which integrates a 2.4GHz, IEEE
802.15.4-compliant transceiver as well as IEEE
802.15.4 PHY and MAC.
24 MHz high stability Xtal is available aboard the
module to perform the timing requirements as per
ZigBee specifications.
A single supply voltage is requested to power the
module. An integrated 2.5 GHz specific Murata
antenna is aboard. The voltage supply also
determines the I/O ports level allowing an easy
interface with the host system.
The module is controlled by means of a standard
serial interface (SPI) allowing the connections to a
variety of Host microcontrollers.
( for other information and details, please refer to
SN260 Datasheet available at www.st.com )
September 2007
Rev 1
1/14
www.st.com
14
1 page  
www.DataSheet4U.com
SPZB260
3 Maximum ratings
3.1
Absolute maximum ratings
Table 2. Absolute maximum ratings
Symbol
Parameter
VDD
VIN
Tstg
Tsold
Module supply voltage
Input voltage on any digital pin
Storage temperature
Soldering temperature < 10s
3.2
Operating ranges
Table 3. Operating ranges
Symbol
Parameter
VDD Module supply voltage
Tstg
Operating ambient
temperature
Conditions
- 20°C < T < 70 °C
Maximum ratings
Values
Min Max
-0.3 3.6
-0.3 Vdd+0.3
-40 +85
240
Unit
V
V
°C
Values
Min Typ Max
2.1 3.3 3.6
Unit
V
-20 +70 °C
5/14
5 Page 
www.DataSheet4U.com
SPZB260
FCC statement
A.1
Label instruction
Instruction manual for FCC ID labeling
Module type:
ZigBee module
SPZB260
FCC-ID:
S9NZB260A
This intends to inform you how to specify the FCC ID of our ZigBee module SPZB260 on
your final product.
Based on the Public Notice from FCC, the product into which our transmitter module is
installed must display a label referring to the enclosed module.
The label should use wording such as “Contains Transmitter module FCC ID: S9NZB260A
or “Contains FCC ID: S9NZB260A , any similar wording that expressed the same meaning
may be use.
It shows an example below
Contains FCC ID: S9NZB260A
A.2
Special requirement for Modular application
The following requirements are fulfilled:
1. The modular transmitter must have its own RF shielding:
The RF module used on the board fulfils the emission requirements of the FCC rules
without additional shielding.
2. The modular transmitter must have buffered modulation/data inputs:
The module has a memory management unit inside of the IC. The processor
interfacing with the external application by means general purpose I/O ( GPIO) , Uart,
SPI. The processor interfaces also the RF part of the module exchanging data and
command with it. Inside the processor a flash memory is available to download the
customer application and the ZigBee profiles.
3. The modular transmitter must have its own power supply regulation:
The IC contains an own voltage regulation. In case of changes in the supply voltage
VCC (for example caused by temperature changes or other effects), the internal
voltage will be stabilized.
4. The modular transmitter must comply with the antenna requirements of Section 15.203
and 15.204:
The RF module is for OEM (Original Equipment Manufacturer) integration only. The
end-user product will be professionally installed in such a manner that only the
authorized antenna is used.
5. The modular transmitter must be tested in a stand-alone configuration:
The RF module was tested in a stand-alone configuration.
6. The modular transmitter must be labelled with its own FCC ID number:
The RF module will be labelled with its own FCC ID number. When the module is
installed inside the end-product, the label is not visible. The OEM manufacturer is
instructed how to apply the exterior label.
11/14
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet SPZB260.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SPZB260 | Wireless Communication & Connectivity ICs and Modules | ST Microelectronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |