|
|
|
부품번호 | 596287775 기능 |
|
|
기능 | Standard Microcircuit Drawing | ||
제조업체 | ETC | ||
로고 | |||
전체 10 페이지수
www.DataSheet4U.com
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
A Add device type 02. Technical changes to table 1. Editorial changes
throughout.
B Drawing updated to reflect current requirements. - gt.
81-09-30
04-06-18
APPROVED
N.A. Hauck
R. Monnin
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
REV
B
SHEET
1
PREPARED BY
Marcia B. Kelleher
B
2
CHECKED BY
Charles E. Besore
APPROVED BY
Michael A. Frye
DRAWING APPROVAL DATE
87-12-30
BBBBBBB
3456789
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
MICROCIRCUIT, LINEAR, 5-VOLT POSITIVE
REGULATOR, MONOLITHIC SILICON
AMSC N/A
DSCC FORM 2233
APR 97
REVISION LEVEL
B
SIZE
A
SHEET
CAGE CODE
67268
1 OF 9
5962-87775
5962-E272-04
www.DataSheet4U.com
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-
38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
B
5962-87775
SHEET
4
4페이지 www.DataSheet4U.com
Letter
A
A1
φD
φD1
E
e
e1
e2
F
L
L1
R
R1
φb
φH
q
Min
0.325
0.760
0.880
0.980
0.660
0.425
0.210
0.060
0.420
0.485
0.168
0.038
0.151
1.177
Inches
Max
0.352
0.116
0.775
0.915
1.020
0.670
0.435
0.220
0.070
0.480
0.025
0.510
0.178
0.043
0.161
1.197
Millimeters
Min Max
8.26 8.94
2.95
19.30
19.69
22.35
23.24
24.90
25.91
16.76
17.02
10.80
11.05
5.33 5.59
1.52 1.78
10.67
12.19
0.64
12.39
12.95
4.27 4.52
0.97 1.09
3.84 4.09
29.90
30.40
FIGURE 1. Case outline - continued.
Device types
Case outline
Terminal number
1
2
Case
01
Y
Terminal symbol
Input
Output
Gnd
FIGURE 2. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
B
5962-87775
SHEET
7
7페이지 | |||
구 성 | 총 10 페이지수 | ||
다운로드 | [ 596287775.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
596287775 | Standard Microcircuit Drawing | ETC |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |