BD3005HFP Datasheet PDF - ROHM Semiconductor
| Part Number | BD3005HFP | |
| Description | Voltage Regulator | |
| Manufacturers | ROHM Semiconductor | |
| Logo |  |
|
|
There is a preview and BD3005HFP download ( pdf file ) link at the bottom of this page. Total 11 Pages | ||
Preview 1 page No Preview Available !
TECHNICAL NOTE
Power Management LSI Series for Automotive Body Control
Regulators with
Voltage Detector and
Watchdog Timer
BD3004HFP,BD3005HFP
zDescription
The BD3004HFP,BD3005HFP low bias current regulator and watchdog timer features a high 50 V breakdown voltage and is compatible
with on-board vehicle microcontrollers. It offers an output current of 500 mA while limiting bias current to 80 µA (Typ.). The series supports
the use of ceramic capacitors as output phase compensation capacitors.The reset detection voltage can be changed by connecting a
resistor to the Vs pin.（BD3004HFP）The watchdog timer can be switched on and off using the INH pin input logic.（BD3005HFP）
zFeatures
1) 5 V/500 mA regulators for microcontrollers
BD3004HFP: Adjustable detection voltage (Vs pin)
BD3005HFP:Built-in watchdog timer reset circuit (INH pin: watchdog timer on/off)
2) Super-low bias current: 80 µA (Typ.)
3) Low-saturation voltage type P-channel DMOS output transistors
4) High precision output voltage: 5 V ±2%
5) Low-ESR ceramic capacitors can be used as output capacitors
6) Vcc Maximum applied voltage: 50 V
7) Built-in overcurrent protection circuit and thermal shutdown circuit
8) Built-in reverse connection breakdown prevention circuit
9) Back current flow protection during sudden battery failures, making it a highly reliable 5 V regulator.
10) HRP7 package
zApplications
Onboard devices (Vehicle equipment, Car stereos, Satellite navigation systems, etc.)
zAbsolute maximum ratings (Ta = 25°C)
Parameter
Vcc applied voltage
Symbol
Vcc
Limit
−15 to +50*1
Unit
V
Vs pin voltage(BD3004HFP)
Vs −0.3 to +15
V
INH pin voltage(BD3005HFP)
VINH
−0.3 to +15
V
Regulator output pin voltage
VOUT
−0.3 to +15
V
Reset output pin voltage
VRO
−0.3 to +15
V
Watchdog input pin voltage
VCLK
−0.3 to +15
V
Reset delay setting pin voltage
VCT
−0.3 to +15
V
Output current
IOUT
500
mA
Power dissipation
Pd 1.6*2
W
Operating temperature range
Topr −40 to +125
°C
Storage temperature range
Tstg −55 to +150
°C
Maximum junction temperature
Tjmax
150
°C
*1 Must not exceed Pd.
*2 Reduced by 12.8 mW/°C over 25°C, when mounted on a glass epoxy board (70 mm × 70 mm × 1.6 mm).
Ver.B July 2006
|
| |
 
● Detection voltage adjustment
OUT
R4
Vs Detection voltage
1,25V(Typ.)
R3
R2=3.56MΩ
For a basic detection voltage of 4.1 V,
Vdet = Vs × (R1 + R2 / R1)
To change the detection voltage,
insert pull-down resistor R3 (with a resistance value lower than R1)
R1=1.56MΩ
between the Vs and GND pins, and pull-up resistor R4 (with a
resistance value lower than R2) between the Vs and Vo pins.
Vdet = Vs × (R3 + R4 / R3) [R3<<R1, R4<<R2]
(All resistance values are typical ones.)
zTiming chart
Fig.15
Vcc
0
VOUT
VdetH
Vdet
0
VINH
0
When VINH = high
WDT current off
VHS
VdetH = Vdet + VHS
CLK
0
TWCLK TWCLK
VthH
VCT0VthL
TWL
TdLH TWH
RESET
0
(1)(2)(3) (4)(5) (6) (7)
(4)(5)(8)(9) (4)(5) (10)(2)(3)(10)(2)(3)(4)(5)(10)(11)
Fig.16
zExplanation
(1) When the output voltage (VOUT) reaches 1.0 V, the reset pin voltage (RESET) will switch to low level.
(2) When VOUT reaches or exceeds the reset clear voltage (VdetH), the external capacitor connected to the CT pin will begin to charge.
When the CT pin voltage (VCT) reaches the upper switching threshold voltage (VthH), RESET will maintain a low-level signal. When
VCT reaches the VthH voltage, RESET will switch from low to high level. The time from VCT reaching or exceeding the VdetH voltage
until RESET reverses (the RESET transmission delay time: TdLH) is given by the following equation:
TdLH (s) ≈ (1.26 × CT (µF)) / Icto (µA) [1]
(3) The watchdog timer operates when RESET rises.
(4) When VCT reaches the lower switching threshold voltage (VthL), the CT pin switches from discharging to charging, and RESET
switches from high level to low level. The watchdog timer reset time TWL is given by the following equation:
TWL(s) ≈ (1.02 × CT (µF)) / Icto (µA) [2]
(5) The CT pin state switches from charge to discharge when VCT reaches VthH, and RESET switches from low to high.
The watchdog timer monitor time TWH is given by the following equation:
TWH(s) ≈ (1.02 × CT (µF)) / Ictc (µA) [3]
(6) The CT pin state may not switche from charge to discharge when the CLK input pulse width (TWCLK) is short.
Use a TWCLK input pulse width of at least 500 ns.
(7) When a pulse (positive edge trigger) of at least 500 ns is input to the CLK pin while the CT pin is discharging, VCT switches from
discharging to charging and then switches back to discharging once it charges to VthH.
(8) Watchdog timer operation is forced off when the INH pin switches to high. At that time, only the watchdog timer will be turned off, and
reset detection will operate normally.
(9) The watchdog timer function turns on when the INH pin switches to low. At that time, the external capacitor on the CT pin will be
discharged.
(10) RESET switches from high to low when OUT falls to the RESET detection voltage (VDET) or lower.
(11) When VOUT falls to 0 V, the RESET signal stays low until VOUT reaches 1.0 V
5/8
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for BD3005HFP electronic component. |
| Information | Total 11 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ BD3005HFP.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| BD3005HFP | The function is Voltage Regulator. ROHM Semiconductor | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
BD30
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||