Datasheet.kr   

LM24 데이터시트 PDF




National Semiconductor에서 제조한 전자 부품 LM24은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 LM24 자료 제공

부품번호 LM24 기능
기능 Monolithic Triple 7.5 ns CRT Driver
제조업체 National Semiconductor
로고 National Semiconductor 로고


LM24 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 9 페이지수

미리보기를 사용할 수 없습니다

LM24 데이터시트, 핀배열, 회로
August 1999
LM2409
Monolithic Triple 9.5 ns CRT Driver
General Description
The LM2409 is an integrated high voltage CRT driver circuit
designed for use in color monitor applications. The IC con-
tains three high input impedance, wide band amplifiers
which directly drive the RGB cathodes of a CRT. Each chan-
nel has its gain internally set to −14 and can drive CRT ca-
pacitive loads as well as resistive loads present in other ap-
plications, limited only by the package’s power dissipation.
The IC is packaged in an industry standard 11-lead TO-220
molded plastic power package. See Thermal Considerations
section.
Features
n Dissipates approximately 50% less power than the
LM2406
n Well matched with LM1279 video preamp
n 0V to 5V input range
n Stable with 0 pF–20 pF capacitive loads and inductive
peaking networks
n Convenient TO-220 staggered lead package style
n Standard LM240X Family Pinout which is designed for
easy PCB layout
Applications
n 1024 x 768 Displays up to 70 Hz Refresh
n Pixel clock frequencies up to 75 MHz
n Monitors using video blanking
Schematic and Connection Diagrams
DS100838-1
FIGURE 1. Simplified Schematic Diagram
(One Channel)
DS100838-2
Note: Tab is at GND
Top View
Order Number LM2409T
© 1999 National Semiconductor Corporation DS100838
www.national.com




LM24 pdf, 반도체, 판매, 대치품
Theory of Operation
The LM2409 is a high voltage monolithic three channel CRT
driver suitable for high resolution display applications. The
LM2409 operates with 80V and 12V power supplies. The
part is housed in the industry standard 11-lead TO-220
molded plastic power package.
The circuit diagram of the LM2409 is shown in Figure 1. The
PNP emitter follower, Q5, provides input buffering. Q1 and
Q2 form a fixed gain cascode amplifier with resistors R1 and
R2 setting the gain at −14. Emitter followers Q3 and Q4 iso-
late the high output impedance of the cascode stage from
the capacitance of the CRT cathode which decreases the
sensitivity of the device to load capacitance. Q6 provides bi-
asing to the output emitter follower stage to reduce cross-
over distortion at low signal levels.
Figure 2 shows a typical test circuit for evaluation of the
LM2409. This circuit is designed to allow testing of the
LM2409 in a 50environment without the use of an expen-
sive FET probe. In this test circuit, two low inductance resis-
tors in series totaling 4.95 kform a 100:1 wideband, low
capacitance probe when connected to a 50coaxial cable
and a 50load (such as a 50oscilloscope input). The in-
put signal from the generator is ac coupled to the base of
Q5.
Application Hints
INTRODUCTION
National Semiconductor (NSC) is committed to provide ap-
plication information that assists our customers in obtaining
the best performance possible from our products. The follow-
ing information is provided in order to support this commit-
ment. The reader should be aware that the optimization of
performance was done using a specific printed circuit board
designed at NSC. Variations in performance can be realized
due to physical changes in the printed circuit board and the
application. Therefore, the designer should know that com-
ponent value changes may be required in order to optimize
performance in a given application. The values shown in this
document can be used as a starting point for evaluation pur-
poses. When working with high bandwidth circuits, good lay-
out practices are also critical to achieving maximum perfor-
mance.
IMPORTANT INFORMATION
The LM2409 performance is targeted for the VGA (640 x
480) to XGA (1024 x 768, 70 Hz refresh) resolution market.
It is designed to be a replacement for discrete CRT drivers.
The application circuits shown in this document to optimize
performance and to protect against damage from CRT arc-
over are designed specifically for the LM2409. If another
member of the LM240X family is used, please refer to its
datasheet.
POWER SUPPLY BYPASS
Since the LM2409 is a wide bandwidth amplifier, proper
power supply bypassing is critical for optimum performance.
Improper power supply bypassing can result in large over-
shoot, ringing or oscillation. A 0.01 µF capacitor should be
connected from the supply pin, VCC, to ground, as close to
the supply and ground pins as is practical. Additionally, a
10 µF to 100 µF electrolytic capacitor should be connected
from the supply pin to ground. The electrolytic capacitor
should also be placed reasonably close to the LM2409’s
supply and ground pins. A 0.1 µF capacitor should be con-
nected from the bias pin, VBB, to ground, as close as is prac-
tical to the part.
ARC PROTECTION
During normal CRT operation, internal arcing may occasion-
ally occur. Spark gaps, in the range of 200V, connected from
the CRT cathodes to CRT ground will limit the maximum volt-
age, but to a value that is much higher than allowable on the
LM2409. This fast, high voltage, high energy pulse can dam-
age the LM2409 output stage. The application circuit shown
in Figure 9 is designed to help clamp the voltage at the out-
put of the LM2409 to a safe level. The clamp diodes, D1 and
D2, should have a fast transient response, high peak current
rating, low series impedance and low shunt capacitance.
FDH400 or equivalent diodes are recommended. Do not use
1N4148 or equivalent diodes for the clamp diodes. D1 and
D2 should have short, low impedance connections to VCC
and ground respectively. The cathode of D1 should be lo-
cated very close to a separately decoupled bypass capacitor
(C3 in Figure 9). The ground connection of D2 and the de-
coupling capacitor should be very close to the LM2409
ground. This will significantly reduce the high frequency volt-
age transients that the LM2409 would be subjected to during
an arcover condition. Resistor R2 limits the arcover current
that is seen by the diodes while R1 limits the current into the
LM2409 as well as the voltage stress at the outputs of the
device. R2 should be a 1/2W solid carbon type resistor. R1
can be a 1/4W metal or carbon film type resistor. Having
large value resistors for R1 and R2 would be desirable, but
this has the effect of increasing rise and fall times. Inductor
L1 is critical to reduce the initial high frequency voltage lev-
els that the LM2409 would be subjected to. The inductor will
not only help protect the device but it will also help maximize
rise and fall times as well as minimize EMI. For proper arc
protection, it is important to not omit any of the arc protection
components shown in Figure 9.
DS100838-10
FIGURE 9. One Channel of the LM2409 with the Recommended Arc Protection Circuit
www.national.com
4

4페이지










LM24 전자부품, 판매, 대치품
Application Hints (Continued)
FIGURE 11. LM1279/240X Demo Board Layout
DS100838-14
7 www.national.com

7페이지


구       성 총 9 페이지수
다운로드[ LM24.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
LM20

LM20 2.4V/ 10A/ SC70/ micro SMD Temperature Sensor

National Semiconductor
National Semiconductor
LM20

Diode (spec sheet)

American Microsemiconductor
American Microsemiconductor

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵