Datasheet.kr   

ELM331 데이터시트 PDF




ELM Electronics에서 제조한 전자 부품 ELM331은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 ELM331 자료 제공

부품번호 ELM331 기능
기능 Solid State Thermostat
제조업체 ELM Electronics
로고 ELM Electronics 로고


ELM331 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 4 페이지수

미리보기를 사용할 수 없습니다

ELM331 데이터시트, 핀배열, 회로
ELM331
Solid State Thermostat
Description
The ELM331 is a complete temperature
measurement and control system in an 8 pin
package.
This integrated circuit is designed to compare
two resistances and drive an output pin depending
on the relative value of each. Typically, one of the
resistors will be an NTC thermistor, and the other
one will be a temperature independent resistor
(whether fixed or variable). When the magnitude of
the resistance connected to pin 2 exceeds the value
of the resistance connected to pin 3, the output pin
www.DataSheewti4llUb.ecodmriven to a high state. Hysteresis maintains
the output in that state until the relative values differ
by approximately 8% (or typically 2°C for a 10K
thermistor).
To reduce the possibility of sporadic outputs, a
condition must exist for three successive cycles, or 6
seconds, before the output pin can change state.
Applications
• Primary thermostat in temperature control
systems
• Staging control for auxiliary heating or cooling
installations
• Under or over temperature alarms
Features
• Low power CMOS design - typically 1mA at 5V
• Wide supply range - 3.0 to 5.5 volt operation
• Built-in proportional hysteresis
• Measurement in progress output
• Time delay on operate improves noise immunity
• Internal pullup resistor on the reset input
• High current drive outputs - up to 25 mA
Connection Diagram
PDIP and SOIC
(top view)
VDD 1
R1 2
R2 3
reset 4
8 VSS
7 Out
6 MIP
5 Cap
Block Diagram
reset 4
2
R1 3
R2
5
VDD
Control
Watchdog
Timer
Measurement in Progress (busy)
6 MIP
Overrange
Analog to
Digital
Converter
R1 > R2
3 Consecutive
Measurements
7 Out
ELM331DSB
Elm Electronics – Circuits for the Hobbyist
< http://www.elmelectronics.com/ >
1 of 4




ELM331 pdf, 반도체, 판매, 대치품
ELM331
Example Application
Figure 1 shows the ELM331 in an example heating
control circuit. A closed contact output occurs
whenever the temperature measured by RTEMP falls to
a value less than that determined by RSET. It is
anticipated that this type of circuit could possibly be
used to control temperatures over the range of -40°C
to +40°C.
Power for the circuit is from a 12V supply, that is
reduced to 5V by the 78L05 regulator. This gives a
stable supply voltage for the ELM331, as well as
convenient voltage for use with a standard relay coil.
The type of relay is not important, as long as
consideration is given to its coil requirements, and the
capabilities of the ELM331. In this example, a relay
www.DataSheewti4thU.aco4m00coil resistance was chosen so that a
2N3904 could drive it directly.
Temperature measuring is performed by RTEMP,
which is a negative temperature coefficient type
thermistor. It has a resistance of 10Kat 25°C, and
this value decreases with increasing temperature. This
value was chosen both because it is commonly
available, and because it limits the 0.1µF integrating
capacitor currents to less than 1mA over the typical
range of operation (keeping the thermistor self-heating
to a minimum).
If the thermistor is mounted any appreciable
distance from the ELM331, consideration must be
given to cabling effects such as capacitive and induced
currents. Generally the integrated circuit can be
adequately protected by mounting a small value (220 )
resistor physically close to the ELM331 as shown
below. Take into account it’s value when determining
the setpoint, though.
For this design, RSET was selected to be equal to
the resistance of RTEMP at 10°C, so that the relay
contact closes for any measured temperatures less
than 10°C. The resistance value was determined from
specs given by the manufacturer, but could have been
determined experimentally as well.
An LED has been provided for visual feedback of
the circuit operation. It is connected to the
‘measurement in progress’ output, so that it is
energized each time a measurement is being made.
Typically, this would be for about 25mS every 2
seconds.
Variations on this circuit could easily be made…
Simply by reversing RSET and RTEMP, one obtains a
cooling control thermostat… Rather than a relay output,
the circuit could have been connected directly to other
logic circuits. The measurement in progress pin could
then be used either as an interrupt, or as a busy flag
that can clock in new results on it’s falling edge…
Battery backup is another option that could be
added to this circuit, but then consideration should be
given to using the ELM341 Low Power Thermostat…
+12V
0.1µF
78L05
0.1µF
RTEMP
10K
@25°C
1
2
see text
3
4
RSET
18K
8
7
6
5
10K
0.1µF
1N4001
2.2K
+12V
12V Relay
To the
heating
control
2N3904
560
LED
ELM331DSB
Figure 1. Backup Heating Control Thermostat
Elm Electronics – Circuits for the Hobbyist
< http://www.elmelectronics.com/ >
4 of 4

4페이지












구       성 총 4 페이지수
다운로드[ ELM331.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
ELM331

Solid State Thermostat

ELM Electronics
ELM Electronics
ELM334

Solid State Thermostat

ELM Electronics
ELM Electronics

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵