Datasheet.kr   

ZT488E 데이터시트 PDF




Zywyn에서 제조한 전자 부품 ZT488E은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 ZT488E 자료 제공

부품번호 ZT488E 기능
기능 (ZT4xxE) Low Power 5V 250kbps/10Mbps RS485 Transceivers
제조업체 Zywyn
로고 Zywyn 로고


ZT488E 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 14 페이지수

미리보기를 사용할 수 없습니다

ZT488E 데이터시트, 핀배열, 회로
ZT485E Low Power 5V 250kbps/10Mbps RS485 Transceivers
Zywyn Corporation
Zywyn
ZT4xxE
ZT483E, ZT485E, ZT488E
ZT489E, ZT490E, ZT491E
Low Power 5V 250kbps/10Mbps RS485 Transceivers
Features
• Meets or exceeds the requirements of ANSI Stan-
dard TIA/EIA-485-A and ISO 8482:1987(E) specifi-
cations for VCC at +5V ±5%
• Low quiescent current – 0.5mA typ., 1mA max.
www.DataSheetL4Uo.wcomshutdown current (where applicable) - 0.01µA
typical, 10µA max.
• Guaranteed standard data rate 250kbps or 10Mbps
• Thermal shutdown protection
• -7V to +12V common-mode input voltage range
• Half-Duplex or Full-Duplex configuration
• Allows up to 1 unit load (32 devices) on the same
common bus
• Controlled driver output slew rate and receiver input
filtering
• Active-high driver enable and active-low receiver
enable
• ESD Protection on bus terminals
±15kV Human Body Model (HBM)
• Drop-in Replacements for MAX483E, MAX485E,
MAX488E, MAX489E, MAX490E, MAX491E.
• High fanout driving 1/4 unit load (128 devices)
available on ZT485ER Series
General Description
The ZT485E series devices are 5V differential data line
transceivers for RS485/RS422 communication that consist
of one driver and one receiver with high level of ESD
protection. They are designed for balanced transmission
lines interface that meet ANSI standard TIA/EIA-485-A and
ISO 8482:1987(E) specifications.
The ZT485E series devices spans out with half or full duplex,
data rate guaranteed at 250k bit per second or 10Mbps, and
allow one unit load that fan out 32 devices sharing a common
bus. The I/Os are enhanced-electrostatic discharge (ESD)
protected, exceeding ±15kV Human Body Model (HBM).
Applications
• RS422/RS485 communications
• Utility meters
• Industrial process control
• Building automation
• Level tranlators
• Transceivers for EMI-sensitive applications
• Routers and HUBs
• Industrial-controlled Local Area Networks
• Industrial PCs, embedded PCs and peripherals
• Industrial, security CATV and camera applications
ZT483E/ZT485E
NowAvailable in Green Package Option
Product Selection GuideAnd Cross Reference
Part
Number
Duplex
# 0f
Tx/Rx
Data
Rate
(Mbps)
# of
Tx/Rx
on Bus
ZT483E Half 1/1 0.25
32
Slew
Rate
Limit
Yes
Rx
Input
Filtering
Low-
Power
Shutdown
Tx/Rx
Enable
Yes Yes Yes
ESD
on
Tx/Rx
± 15kV
Number
of Pins
8
Pin-to-Pin
Cross
Reference
MAX483E
ZT485E Half
1/1
10
32
No
No
Yes Yes ± 15kV 8
MAX485E
ZT488E Full
1/1 0.25
32
Yes Yes
No
No ± 15kV
8
MAX488E
ZT489E Full
1/1 0.25
32
Yes Yes
Yes
Yes ± 15kV
14
MAX489E
ZT490E Full 1/1 10 32 No No
ZT491E Full 1/1 10 32 No No
No
No ± 15kV
8
Yes
Yes ± 15kV
14
MAX490E
MAX491E
Zywyn
Specifications subject to change without notice
1 August 2004
Zywyn Corporation • Tel (408) 733-3225 • Fax (408) 733-3206 • Email [email protected] • www.zywyn.com
rev.1.2




ZT488E pdf, 반도체, 판매, 대치품
Zywyn Corporation
ACElectrical Characteristics (ZT485E, ZT490E, and ZT491E)
Unless otherwise stated, VCC = +5.0V, TA = Tmin to Tmax, typical values apply at VCC = +5.0V and TA = 25°C.
Parameter
Condition
Min
Transmitter Timing
Transmitter Propagation tPLH
Transmitter Propagation tPHL
Transmitter Output Skew tSK
Transmitter Rise/Fall Time
Transmitter Output Enable
Transmitter Output Disable
www.DataSheet4U.com
Receiver Timing
Receiver Propagation tPLH
Receiver Propagation tPHL
Differential Receiver Skew tSK
Receiver Output Enable
Receiver Output Disable
Transceiver Throughput
Maximum Data Rate
ESD Tolerance
ESD HBM
RDIFF = 54Ω, CL = 50pF. Refers to figure 4.
RDIFF = 54Ω, CL = 50pF. Refers to figure 4.
|tPLH - tPHL|
tr, tf , RDIFF = 54Ω, CL = 50pF, ZT485E. Refers to figure 4.
tr, tf , RDIFF = 54Ω, CL = 50pF, ZT490E and ZT491E, refer fig.4.
To Output HIGH, CL = 50pF, RL = 110. Refers to figure 5.
To Output LOW, CL = 50pF, RL = 110. Refers to figure 6.
From Output HIGH, CL = 50pF, RL = 110. Refers to figure 5.
From Output LOW, CL = 50pF, RL = 110Ω. Refers to figure 6.
CL = 15pF, Refers to figure 9.
CL = 15pF, Refers to figure 9.
|tPHL - tPLH|
To Output HIGH, CL = 15pF. Refers to figure 10.
To Output LOW, CL = 15pF. Refers to figure 11.
From Output HIGH, CL = 15pF. Refers to figure 10.
From Output LOW, CL = 15pF. Refers to figure 11.
RL = 54, CL = 50pF, TA = 25°C
RS485 Inputs and Outputs
10
Typ
35
35
3
15
15
50
50
50
50
50
50
10
50
50
50
50
±15
ZT4xxE
Max Units
60 ns
60 ns
10 ns
25 ns
25 ns
ns
ns
ns
ns
150 ns
150 ns
ns
ns
ns
ns
ns
Mbps
kV
Zywyn
Specifications subject to change without notice
4 August 2004
rev.1.2

4페이지










ZT488E 전자부품, 판매, 대치품
Zywyn Corporation
ZT4xxE
Circuit Description
The ZT483E, ZT485E, ZT489E, ZT490E, and ZT491E are
low-power transceivers for RS-485 and RS-422 communica-
tions. The RS-485 standard is ideal for multi-drop applica-
tions and for long-distance interfaces. The TIA/EIA-485
specification allows up to 32 drivers and 32 receivers to be
connected to a data bus, making it an ideal choice for multi-
drop applications. RS-485 transceivers are equipped with a
wide (-7V to +12V) common mode range to accommodate
ground potential differences since the cabling can be as
long as 4,000 feet. As RS-485 is a differential interface, data
is virtually immune to noise in the transmission line.
The ZT483E, ZT488E, and ZT489E are slew-rate limited,
www.DatamShieneimt4Uiz.cinomg EMI and reducing reflections caused by improp-
erly terminated cables.
RS-485 Transmitters
Each device in the ZT4xxE family contains a differential
output line transmitter that can drive voltage into multiple
loads on a terminated two-wire pair, and a receiver that
accepts a differential voltage down to 200mV. The
transmitter's differential output can comply with RS-485 and
also RS-422 standards. The typical voltage output swing
with no load is 0V to VCC. With worst case loading of 54
ohms across the differential outputs, the drivers can main-
tain greater than 1.5V voltage levels, which is more than
adequate for a differential receiver to acknowledge a logic
state. The 54 ohms is the equivalent of two 120 ohm
termination resistors placed on each side of the transmis-
sion line and the input impedance of 32 receivers on the line.
The ZT485E transmitter has an enable control line which is
active HIGH. A logic HIGH on DE (pin 3) will enable the
differential outputs. A logic LOW on DE (pin 3) will disable
the transmitter outputs. While disabled, the transmitter
outputs are in high impedance.
RS-485 Receivers
Each transceiver contains one differential receiver that has
an input sensitivity of 200mV. The input impedance of the
receivers is typically 15 kohms. A wide common mode
range of -7V to +12V allows for large ground potential
differences between systems.
The ZT485E, ZT489E, and ZT491E receivers have an enable
control input. A logic LOW on RE will enable the receiver,
a logic HIGH on RE will disable the receiver. The receivers
are equipped with the fail-safe feature, which guarantees
that the receiver output will be in a HIGH-IMPEDANCE state
when the input is left unconnected.
The ZT485E, ZT490E, and ZT491E can transmit and receive
at data rates up to 10Mbps. The ZT483E, ZT488E, and
ZT489E are specified for data rates up to 250kbps.
Bus Configuration
The ZT489E, ZT490E, and ZT491E are full-duplex transceiv-
ers, while the ZT483E and ZT485E are half-duplex.
For full duplex, the devices are used as a four-wire bus
transceiver with a configuration that the transmitters and
receivers are moving data independent of each other. Trans-
mit can occur on a dedicated two-wire pair and receive can
occur on an adjacent two-wire pair, with each pair transfer-
ring data at up to 10Mbps (up to 250kbps for the ZT489E).
Half duplex is a configuration where the transmitter outputs
are connected to its receiver inputs. This application is
common for two-wire interfaces where either the transmitter
is active or the receiver is active. It is common to connect
the enable inputs for the transmitter and receiver together so
that a logic HIGH will enable the transmitter and disable the
receiver. Conversely, a logic LOW will disable the transmit-
ter and enable the transmitter. Half-duplex configuraitons
and these devices are designed for bidirectional data trans-
mission on multipoint twisted-pair cables for applications,
such as digital motor controllers, remote sensors and
terminals, industrial process control, security stations and
environmental control systems.
ESD Immunity
Electro-Static Discharge (ESD) is an important factor when
implementing a serial port into a system, especially in harsh
environmental conditions. These industrial strength de-
vices provide extra protection against ESD and are intended
for harsh environments where high-speed data communica-
tion is important.
All of the ZT485E family of transceivers incorporate internal
protection structures on all pins to protect against ESD
charges encountered during handling and assembly. The
driver outputs and receiver inputs have extra protection
against static electricity as they are directly interfacing to
the outside environment. As such, these pins against ESD
of ±15kV without damage in all states of the transceiver's
operation in the static state. After multiple ESD events,
Zywyn’s ZT485E family of transceivers keep working without
latchup. These devices eliminate the need for external
transient suppressor diodes and the associated high ca-
pacitance loading, allowing reliable high-speed data com-
munications.
The Human Body Model has been the generally accepted
ESD testing method for semiconductors. This test is in-
tended to simulate the human body’s potential to store
electrostatic energy and discharge it to an integrated circuit
upon close proximity or contact. This method will test the
IC’s capability to withstand an ESD transient during normal
handling such as in manufacturing areas where the ICs tend
to be handled frequently.
Zywyn
Specifications subject to change without notice
7 August 2004
rev.1.2

7페이지


구       성 총 14 페이지수
다운로드[ ZT488E.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
ZT488E

(ZT4xxE) Low Power 5V 250kbps/10Mbps RS485 Transceivers

Zywyn
Zywyn

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵