|
|
|
부품번호 | KP1H 기능 |
|
|
기능 | NON-POLARIZED | ||
제조업체 | DB Lectro | ||
로고 | |||
전체 13 페이지수
KPwww.DataSheet4U.com
Series
CHIP TYPE, NON-POLARIZED WITH WIDE TEMPERATURE RANGE
Non-polarized with wide temperature range up to +105qC
Load life of 1000 hours
Comply with the RoHS directive (2002/95/EC)
SPECIFICATIONS
Items
Operation Temperature Range
Rated Working Voltage
Capacitance Tolerance
Leakage Current
Dissipation Factor max.
Characteristics
-55 ~ +105°C
6.3 ~ 50V
±20% at 120Hz, 20°C
I d 0.05CV or 10ȝA whichever is greater (after 2 minutes)
I: Leakage current (PA) C: Normal capacitance (PF)
Measurement frequency: 120Hz, Temperature: 20°C
WV 6.3
10
16
25
V: Rated voltage (V)
35 50
tan į 0.24 0.20 0.17 0.17 0.15 0.15
Rated voltage (V)
6.3 10 16 25 35 50
Low Temperature Characteristics
(Measurement frequency: 120Hz)
Impedance ratio Z(-25°C) / Z(20°C)
ZT/Z20 (max.) Z(-40°C) / Z(20°C)
4
8
3
6
2
4
2
4
2
3
2
3
Load Life
(After 1000 hours application of the
rated voltage at 105°C with the
polarity inverted every 250 hours,
capacitors meet the characteristics
requirements listed.)
Shelf Life
Resistance to Soldering Heat
Capacitance Change
Dissipation Factor
Leakage Current
Within r20% of initial value
200% or less of initial specified value
Initial specified value or less
After leaving capacitors under no load at 105°C for 1000 hours, they meet the specified value
for load life characteristics listed above.
After reflow soldering according to Reflow Soldering Condition (see page 8) and restored at
room temperature, they meet the characteristics requirements listed as below.
Capacitance Change
Dissipation Factor
Leakage Current
Within r10% of initial value
Initial specified value or less
Initial specified value or less
Reference Standard
JIS C-5141 and JIS C-5102
DRAWING (Unit: mm)
Plastic plateform
0.3max.
Cf0.2
Positive
L
+0.1
-0.2
DIMENSIONS (Unit: mm)
D x L
A
B
C
E
L
0.5~0.8
Negative
*Voltage mark for 6.3V is [6V]
4 x 5.4
1.8
4.3
4.3
1.0
5.4
5 x 5.4
2.1
5.3
5.3
1.3
5.4
6.3 x 5.4
2.4
6.6
6.6
2.2
5.4
DB LECTRO Inc. 3755 Place Java, Suite 140, Brossard, Québec, J4Y 0E4, Canada - T: 1-450-444-1424 / F: 1-450-444-4714 / www.dblectro.com
www.DataSheet4U.com CORRESPONDING TO RoHS DIRECTIVE
Aluminum electrolytic
capacitors
RoHS compliant
RoHS
restricted
substances
Most concerns
on terminals
Plating on
terminals
Chip type
Yes
Radial lead type
Yes
Snap-in type
Yes
Change plating from Sn-Pb to Change plating from Sn-Pb to Change plating from Sn-Pb to
Sn Sn Sn
Construction of
terminals
Plating
characters
Fe/Cu/Sn
Fe/Cu/Sn
Fe/Cu/Sn
Plating thickness 12Pm
Plating thickness 12Pm
Plating thickness 10Pm
Plating type matte
Plating type matte
Plating type matte
No heat treatment after plating No heat treatment after plating No heat treatment after plating
Insulating
sleeve
No used
Replace PVC with PET
Replace PVC with PET
(where customer designated) (where customer designated)
Please see "Lead Free Reflow
Resistance to Soldering Condition" for chip
Pb
soldering heat type aluminum electrolytic
No change
capacitors
No change
Solderability
No difference with Sn-Pb
No difference with Sn-Pb
No difference with Sn-Pb
Tensile strength No difference with Sn-Pb
No difference with Sn-Pb
No difference with Sn-Pb
Whisker
No difference with Sn-Pb
Room storage test: 20~25qC,
30~80%RH, 4000hrs.
Aging test: 60r5qC, 93
+2/-3%RH, 4000hrs.
Thermal cycle test: -55
+0/-10qC to 85 +10/-0qC, 3
cycles/hour, 1000 cycles
No difference with Sn-Pb
Room storage test: 20~25qC,
30~80%RH, 4000hrs.
Aging test: 60r5qC, 93
+2/-3%RH, 4000hrs.
Thermal cycle test: -55
+0/-10qC to 85 +10/-0qC, 3
cycles/hour, 1000 cycles
Whisker is not observed
Room storage test: 20~25qC,
30~80%RH, 4000hrs.
Aging test: 60r5qC, 93
+2/-3%RH, 4000hrs.
Thermal cycle test: -55
+0/-10qC to 85 +10/-0qC, 3
cycles/hour, 1000 cycles
Cr6+ Plating material < 2ppm
< 2ppm
< 2ppm
Hg
< 2ppm
< 2ppm
< 2ppm
Cd
< 2ppm
< 2ppm
< 2ppm
PBB
Not detected
Not detected
Not detected
PBDE
Not detected
Not detected
Not detected
Identification for RoHS
compliance products
Add "Pb free" or "RoHS"
marking on inner and outer
carton label (where customer
designated)
Add "Pb free" or "RoHS"
marking on inner and outer
carton label (where customer
designated)
Add "Pb free" or "RoHS"
marking on inner and outer
carton label (where customer
designated)
MSL Level
(IPC/JEDEC J-STD-020C)
Not available
No need for dry package
Not available
No need for dry package
Not available
No need for dry package
DB LECTRO Inc. 3755 Place Java, Suite 140, Brossard, Québec, J4Y 0E4, Canada - T: 1-450-444-1424 / F: 1-450-444-4714 / www.dblectro.com
4페이지 GENERALwww.DataSheet4U.com INFORMATION FOR APPLICATION
The following precautions must be observed when using electrolytic capacitors.
1. Circuit Design
1) Please make sure that the environmental and mounting conditions to which the capacitor to be
exposed are within the conditions specified in this catalogue.
2) Operating temperature and applied ripple must be within the specifications.
3) Appropriate capacitors, which comply with the life requirement of the products, should be selected
when designing the circuit.
4) Aluminum electrolytic capacitors are polarized. Do not apply reserve voltage or AC voltage. Please
use non-polarized capacitors for a circuit that can possibly see reserved polarity.
Note: Non-polarizes capacitors cannot be used for AC voltage application.
5) Do not use aluminum electrolytic capacitors in a circuit that requires rapid and very frequent charge
or discharge. In this type of circuit, it is necessary to use special design capacitors with extended life
characteristics.
6) Do not apply excess voltage.
M Pleased pay attention so that the peak voltage, which is DC voltage overlapped by ripple current,
should not exceed the rated voltage.
N In the case where more than two aluminum electrolytic capacitors are used in series, please
make sure that applied voltage should be lower than rated voltage should be applied to each
capacitor equally using a balancing resistor in parallel with the capacitor.
7) Outer sleeved of the capacitor is not guarantee as an electrical insulator. Do not use standard sleeve
on a capacitor in applications that require electrical insulation. When the application requires special
insulation, please contact our sales office for details.
8) Capacitors must not be used under following conditions:
M (a) Capacitors must not be exposed to water (including condensation), brine or oil.
(b) Ambient conditions that include toxic gases such as hydrogen sulfide, sulfurous acid, nitrous
acid, chlorine, ammonium, etc.
(c) Ambient conditions that expose the capacitor to ozone, ultraviolet ray and radiation.
N Severe vibration and physical shock conditions that exceed our specification.
Vibration test condition:
Vibration frequency range: 10~55~10Hz
Sweet rate
: 10~55~10Hz per minute
Sweet method
: logarithmic
Amplitude or acceleration: 1.5 (max. acceleration is 10G)
Direction of vibration : X, Y, Z direction
Testing time
: 2 hours per each direction
Shock is not applicable normally.
If a particular condition is required, please contact our sales office.
DB LECTRO Inc. 3755 Place Java, Suite 140, Brossard, Québec, J4Y 0E4, Canada - T: 1-450-444-1424 / F: 1-450-444-4714 / www.dblectro.com
7페이지 | |||
구 성 | 총 13 페이지수 | ||
다운로드 | [ KP1H.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
KP100 | Surface Mount Capacitive Silicon Absolute Pressure Sensor | Infineon Technologies |
KP1000 | Digital Program Controller | CHINO |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |