PDF NX3L2T66 Data sheet ( Hoja de datos )

Número de pieza	NX3L2T66
Descripción	Low-ohmic single-pole single-throw analog switch
Fabricantes	NXP Semiconductors
Logotipo
Hay una vista previa y un enlace de descarga de NX3L2T66 (archivo pdf) en la parte inferior de esta página. Total 18 Páginas
No Preview Available ! NX3L2T66 Low-ohmic single-pole single-throw analog switch Rev. 01 — 4 December 2008 Product data sheet www.datasheet4u.com 1. General description The NX3L2T66 provides two low-ohmic single pole single throw analog switch functions. Each switch has two input/output terminals (nY and nZ) and an active HIGH enable input (nE). When pin nE is LOW, the analog switch is turned off. Schmitt-trigger action at the enable input (nE) makes the circuit tolerant to slower input rise and fall times across the entire VCC range from 1.4 V to 3.6 V. A low input voltage threshold allows pin nE to be driven by lower level logic signals without a signiﬁcant increase in supply current ICC. This makes it possible for the NX3L2T66 to switch 3.6 V signals with a 1.8 V digital controller, eliminating the need for logic level translation. The NX3L2T66 allows signals with amplitude up to VCC to be transmitted from nY to nZ; or from nZ to nY. Its low ON resistance (0.5 Ω) and ﬂatness (0.13 Ω) ensures minimal attenuation and distortion of transmitted signals. 2. Features I Wide supply voltage range from 1.4 V to 3.6 V I Very low ON resistance (peak): N 1.6 Ω (typical) at VCC = 1.4 V N 1.0 Ω (typical) at VCC = 1.65 V N 0.55 Ω (typical) at VCC = 2.3 V N 0.50 Ω (typical) at VCC = 2.7 V I High noise immunity I ESD protection: N HBM JESD22-A114E Class 3A exceeds 7500 V N MM JESD22-A115-A exceeds 200 V N CDM AEC-Q100-011 revision B exceeds 1000 V I CMOS low-power consumption I Latch-up performance exceeds 100 mA per JESD 78 Class II Level A I 1.8 V control logic at VCC = 3.6 V I Control input accepts voltages above supply voltage I Very low supply current, even when input is below VCC I High current handling capability (350 mA continuous current under 3.3 V supply) I Speciﬁed from −40 °C to +85 °C and from −40 °C to +125 °C 1 page NXP Semiconductors NX3L2T66 Low-ohmic single-pole single-throw analog switch 11. Static characteristics www.datasheet4u.com Table 7. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground 0 V). Symbol Parameter Conditions 25 °C Min Typ Max VIH VIL II IS(OFF) IS(ON) ICC ∆ICC CI CS(OFF) CS(ON) HIGH-level input voltage LOW-level input voltage input leakage current OFF-state leakage current VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 1.4 V to 1.6 V VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V enable input nE; VI = GND to 3.6 V; VCC = 1.4 V to 3.6 V Y port; VCC = 1.4 V to 3.6 V; see Figure 5 ON-state leakage current Z port; VCC = 1.4 V to 3.6 V; see Figure 6 supply current additional supply current input capacitance VI = VCC or GND; VCC = 3.6 V; VSW = GND or VCC VI = 2.6 V; VCC = 3.6 V; VSW = GND or VCC VI = 1.8 V; VCC = 3.6 V; VSW = GND or VCC VI = 1.8 V; VCC = 2.5 V; VSW = GND or VCC OFF-state capacitance ON-state capacitance 0.9 - - 0.9 - - 1.1 - - 1.3 - - - - 0.3 - - 0.4 - - 0.4 - - 0.5 --- - - ±5 - - ±5 - - 100 - 0.35 0.7 - 2.5 4 - 50 200 - 1.0 - - 35 - - 110 - −40 °C to +125 °C Unit Min Max Max (85 °C) (125 °C) 0.9 - -V 0.9 - -V 1.1 - -V 1.3 - -V - 0.3 0.3 V - 0.4 0.3 V - 0.4 0.4 V - 0.5 0.5 V - ±0.5 ±1 µA - ±50 ±500 nA - ±50 ±500 nA 690 6000 nA - 1 1 µA - 5 5 µA - 300 500 nA - - - pF - - - pF - - - pF NX3L2T66_1 Product data sheet Rev. 01 — 4 December 2008 © NXP B.V. 2008. All rights reserved. 5 of 18 5 Page NXP Semiconductors NX3L2T66 Low-ohmic single-pole single-throw analog switch Table 12. Additional dynamic characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V); VI = GND or VCC (unless otherwise www.dsaptaeschiﬁeeedt4)u; .tcro=mtf ≤ 2.5 ns. Symbol Parameter Conditions 25 °C Unit Min Typ Max Qinj charge injection fi = 1 MHz; CL = 0.1 nF; RL = 1 MΩ; Vgen = 0 V; Rgen = 0 Ω; see Figure 21 VCC = 1.5 V VCC = 1.8 V - 3 - pC - 3 - pC VCC = 2.5 V - 3 - pC VCC = 3.3 V - 3 - pC [1] fi is biased at 0.5VCC. 12.3 Test circuits VIH nE nY/nZ VCC 0.5VCC nZ/nY RL fi D Fig 16. Test circuit for measuring total harmonic distortion 001aaj225 VIH nE nY/nZ VCC 0.5VCC nZ/nY RL fi dB 001aaj226 Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads −3 dB. Fig 17. Test circuit for measuring the frequency response when channel is in ON-state NX3L2T66_1 Product data sheet Rev. 01 — 4 December 2008 © NXP B.V. 2008. All rights reserved. 11 of 18 11 Page

Páginas	Total 18 Páginas
PDF Descargar	[ Datasheet NX3L2T66.PDF ]

Hoja de datos destacado

Número de pieza	Descripción	Fabricantes
NX3L2T66	Low-ohmic single-pole single-throw analog switch	NXP Semiconductors

Número de pieza	Descripción	Fabricantes
SLA6805M	High Voltage 3 phase Motor Driver IC.	Sanken
SDC1742	12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.	Analog Devices

DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.

DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar