Datasheet.kr   

NX3L1T53 데이터시트 PDF




NXP Semiconductors에서 제조한 전자 부품 NX3L1T53은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 NX3L1T53 자료 제공

부품번호 NX3L1T53 기능
기능 Low-ohmic Single-pole Double-throw Analog Switch
제조업체 NXP Semiconductors
로고 NXP Semiconductors 로고


NX3L1T53 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 23 페이지수

미리보기를 사용할 수 없습니다

NX3L1T53 데이터시트, 핀배열, 회로
NX3L1T53
Low-ohmic single-pole double-throw analog switch
Rev. 02 — 14 April 2009
Product data sheet
www.datasheet4u.com
1. General description
The NX3L1T53 provides one low-ohmic single-pole double-throw analog switch, suitable
for use as an analog or digital multiplexer/demultiplexer. It has a digital select input (S),
two independent inputs/outputs (Y0, Y1), a common input/output (Z) and an active LOW
enable input (E). When pin E is HIGH, the switch is turned off. Schmitt-trigger action at the
select input (S) and enable input (E) makes the circuit tolerant to slower input rise and fall
times across the entire VCC range from 1.4 V to 4.3 V.
A low input voltage threshold allows pins S and E to be driven by lower level logic signals
without a significant increase in supply current ICC. This makes it possible for the
NX3L1T53 to switch 4.3 V signals with a 1.8 V digital controller, eliminating the need for
logic level translation.
The NX3L1T53 allows signals with amplitude up to VCC to be transmitted from Z to Y0 or
Y1; or from Y0 or Y1 to Z. It’s low ON resistance (0.5 ) and flatness (0.13 ) ensures
minimal attenuation and distortion of transmitted signals.
2. Features
I Wide supply voltage range from 1.4 V to 4.3 V
I Very low ON resistance (peak):
N 1.6 (typical) at VCC = 1.4 V
N 1.0 (typical) at VCC = 1.65 V
N 0.55 (typical) at VCC = 2.3 V
N 0.50 (typical) at VCC = 2.7 V
N 0.50 (typical) at VCC = 4.3 V
I Break-before-make switching
I High noise immunity
I ESD protection:
N HBM JESD22-A114E Class 3A exceeds 7500 V
N MM JESD22-A115-A exceeds 200 V
N CDM AEC-Q100-011 revision B exceeds 1000 V
I CMOS low-power consumption
I Latch-up performance exceeds 100 mA per JESD 78 Class II Level A
I 1.8 V control logic at VCC = 3.6 V
I Control input accepts voltages above supply voltage
I Very low supply current, even when input is below VCC
I High current handling capability (350 mA continuous current under 3.3 V supply)
I Specified from 40 °C to +85 °C and from 40 °C to +125 °C




NX3L1T53 pdf, 반도체, 판매, 대치품
NXP Semiconductors
NX3L1T53
Low-ohmic single-pole double-throw analog switch
www.datasheet4u.com
terminal 1
index area
NX3L1T53
Y0 1
7Z
Y1 2
6E
S3
5 GND
Fig 5. Pin configuration SOT902-1 (XQFN8U)
001aaj538
Transparent top view
7.2 Pin description
Table 3.
Symbol
Z
E
GND
GND
S
Y1
Y0
VCC
Pin description
Pin
SOT833-1 and SOT996-2
1
2
3
4
5
6
7
8
SOT902-1
7
6
5
4
3
2
1
8
8. Functional description
Description
common output or input
enable input (active LOW)
ground (0 V)
ground (0 V)
select input
independent input or output
independent input or output
supply voltage
Table 4.
Input
S
L
H
X
Function table[1]
E
L
L
H
[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care.
Channel on
Y0 to Z or Z to Y0
Y1 to Z or Z to Y1
switch off
NX3L1T53_2
Product data sheet
Rev. 02 — 14 April 2009
© NXP B.V. 2009. All rights reserved.
4 of 23

4페이지










NX3L1T53 전자부품, 판매, 대치품
NXP Semiconductors
NX3L1T53
Low-ohmic single-pole double-throw analog switch
11.1 Test circuits
www.datasheet4u.com
VCC
VIL or VIH
VIH
VI
S
Z
E
Y0 1
Y1 2
switch
GND
IS
VI = 0.3 V or VCC 0.3 V; VO = VCC 0.3 V or 0.3 V.
Fig 6. Test circuit for measuring OFF-state leakage current
switch
1
2
S
VIL
VIH
E
VIH
VIH
VO
001aad390
VIL or VIH
VIL
IS
VI
VCC
S
Z
E
Y0 1
Y1 2
switch
GND
switch
1
2
S
VIL
VIH
E
VIL
VIL
VO
VI = 0.3 V or VCC 0.3 V; VO = open circuit.
Fig 7. Test circuit for measuring ON-state leakage current
001aad391
11.2 ON resistance
Table 8. ON resistance
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 9 to Figure 15.
Symbol Parameter
Conditions
40 °C to +85 °C 40 °C to +125 °C Unit
Min Typ[1] Max
Min
Max
RON(peak) ON resistance (peak)
VI = GND to VCC;
ISW = 100 mA;
see Figure 8
VCC = 1.4 V
VCC = 1.65 V
VCC = 2.3 V
VCC = 2.7 V
VCC = 4.3 V
- 1.6 3.7
- 1.0 1.6
- 0.55 0.8
- 0.5 0.75
- 0.5 0.75
-
-
-
-
-
4.1
1.7
0.9
0.9
0.9
NX3L1T53_2
Product data sheet
Rev. 02 — 14 April 2009
© NXP B.V. 2009. All rights reserved.
7 of 23

7페이지


구       성 총 23 페이지수
다운로드[ NX3L1T53.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
NX3L1T5157

Low-ohmic single-pole double-throw switch

NXP Semiconductors
NXP Semiconductors
NX3L1T53

Low-ohmic Single-pole Double-throw Analog Switch

NXP Semiconductors
NXP Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵