Datasheet.kr   

LC72708E 데이터시트 PDF




Sanyo Semicon Device에서 제조한 전자 부품 LC72708E은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 LC72708E 자료 제공

부품번호 LC72708E 기능
기능 FM Multiplex Broadcast Reception IC for Mobile VICS Systems
제조업체 Sanyo Semicon Device
로고 Sanyo Semicon Device 로고


LC72708E 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 15 페이지수

미리보기를 사용할 수 없습니다

LC72708E 데이터시트, 핀배열, 회로
Ordering number : EN5875
CMOS IC
LC72708E
FM Multiplex Broadcast Reception IC
for Mobile VICS Systems
Overview
The LC72708E is a data demodulation IC for receiving
FM multiplex broadcasts for mobile receivers in the
DARC format. The LC72708E also includes a built-in
decoder circuit that performs VICS data processing. This
allows this IC to implement compact high-functionality
VICS reception systems. Note that a contract with VICS
Center is required to evaluate samples of this IC or to
mass produce products that support the VICS system.
Functions
• SCF-based adjustment-free 76-kHz bandpass filter
• VICS decoder circuit
• MSK delay detection circuit based on a 1T delay
• Error correction function based on a 2T delay (in the
MSK detector stage)
• Digital PLL based clock regeneration circuit
• Shift-register type 1T and 2T delay circuits
• Block and frame synchronization detection circuit
• Function for setting the number of allowable BIC errors,
the number of synchronization protection.
• Error correction using (272, 190) codes
• Layer 4 CRC code checking circuit
• On-chip frame memory and memory control circuit for
vertical correction
• 7.2-MHz crystal oscillator circuit
• Two power saving functions (Standby and EC stop)
Package Dimensions
unit: mm
3148-QIP44MA
[LC72708E]
SANYO: QIP44MA
• CCB is a trademark of SANYO ELECTRIC CO., LTD.
• CCB is SANYO’s original bus format and all the bus
addresses are controlled by SANYO.
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
71598RM (OT) No. 5875-1/15




LC72708E pdf, 반도체, 판매, 대치품
LC72708E
Pin Descriptions
Pin No.
28
29
30
33
32
40
9
12
13
14
15
16
17
18
19
41
42
5
6
7
8
20
21
22
25
26
27
3
4
Pin Name
CL
CE
DI
RST
STNBY
TEST
TP0
TP1
TP2
TP3
TP4
TP5
TP6
TP7
TP8
TPC1
TPC2
TOSEL1
TOSEL2
CLK16
DATA
FCK
BCK
FLOCK
BLOCK
CRC4
INT
IC1
IC2
Function
CCB serial interface
Clock input
Data control input
Data input
System reset input (active low)
Standby mode (active high)
Test (Must be connected to ground during normal operation.)
Must be connected to either VDD or VSS.
Clock regeneration monitor
Demodulated data monitor
Frame start signal output
Block start signal output
Outputs a high level during frame synchronization.
Outputs a high level during block synchronization.
Layer 4 CRCC check result output
External CPU interrupt signal
Internal connections. These pins must be left open.
31 DO Data output used by the CCB serial interface
I/O
Input
Input
Output
Output
Circuit type
44 XIN
System clock generation crystal oscillator element connections
1 XOUT
Input
Output
36 MPXIN Baseband (multiplex) signal input
Input
38 FLOUT Subcarrier output (76-kHz filter output)
Output
39 CIN Subcarrier input (comparator input)
Input
Continued on next page.
No. 5875-4/15

4페이지










LC72708E 전자부품, 판매, 대치품
LC72708E
Continued from preceding page.
backward protection count to a value stricter than the default, e.g. to a value of 3 or more as opposed to the default of 2, if
the block synchronization recognition output (the BLOCK pin, pin 23) is used to recognize the presence or absence of
FM multiplex data.
• Frame Synchronization Error Protection Count
This IC detects the four unique BIC inflection points that exist in a single frame, and increments or decrements the
protection counter depending on whether or not the IC internal frame synchronization counter matches. The data values
are set in the same way as those for the block synchronization protection count are set, namely data in which 1 has been
subtracted from the desired protection count must be transferred. The frame synchronization default values are 8 for
forward protection and 2 for backward protection.
• Control Registers
These registers are used to set the IC operating mode. These are described later.
• Notes
— The address bits DI12 to DI15 are ignored.
— Addresses other than those listed above (for example location 0110) are special addresses used for test mode and
other special IC functions. Do not set these locations.
— The default values are the values reloaded into the internal registers when a reset signal (RST) is received. These
values are the recommended values for normal operation, and normally do not need to be modified. If only the
default values are used, there is no need to provide data transfer routines in the external CPU.
Received data
Synchronization
counter BIC position
Block
: Both forward and backward protection counts are 3.
Figure 1 Block Synchronization Protection Operation
(forward backward forward)
Layer 4 CRC Check Circuit
This is a function provided for data group error detection, i.e. layer 4 CRC. After the stipulated number of bytes of data
group data and a 16-bit CRC error check word are transferred, the CRC4 pin outputs a high level if there were no errors.
The CRC4 pin outputs a high level if all the bits in the IC internal CRC check register were 0. When using this function
to perform the layer 4 CRC check, the IC internal CRC check register must be initialized before a single data group data
unit is transferred. This register is initialized by sending bit 7 of the control register. Note that since this flag is not
automatically reset to 0, the application must return it to 0 before transferring layer 4 CRC check data. If there were no
errors in any of the received data groups, the CRC register will always be all zeros after the CRC check of a single data
group. Therefore, the above control register initialization will not be necessary as long as there are no errors in the layer 4
CRC. The data length of the transferred data group data is in unit of 8 bits. Also note that while there is no upper limit on
the amount of data transferred in a single operation, data transfers can also be divided into multiple transfer operations.
No. 5875-7/15

7페이지


구       성 총 15 페이지수
다운로드[ LC72708E.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
LC72708

FM Multiplex Broadcast Reception IC for Mobile VICS Systems

Sanyo Semicon Device
Sanyo Semicon Device
LC72708E

FM Multiplex Broadcast Reception IC for Mobile VICS Systems

Sanyo Semicon Device
Sanyo Semicon Device

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵