|
|
PDF AT78C1502 Data sheet ( Hoja de datos )
| Número de pieza | AT78C1502 | |
| Descripción | DVD/CD Servo | |
| Fabricantes | ATMEL Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AT78C1502 (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
|
No Preview Available !
Features
• Servo Processing Unit (SPU), Using Dedicated 16-bit Instruction Cycle AVR® RISC
Cores (3), Giving 120 MIPS Maximum Processing Power with 40 MHz SYSCLK
• SPU Includes 17 x 17 Single-clock Cycle MAC
• On-chip Debugger Monitor for Program Development (OCDM)
• 8K Words Program RAM
• 4K Bytes Data RAM
• On-chip Clock Frequency Synthesizer with Output Clock Buffers for AT78C1501
Controller
• On-chip S/H and WCS Timing State Machine (TSM) for Conversion of Focus, Tracking
and SUM Signals
• 10-bit 1.2 µsec ADC with six-channel MUX
• Synchronized ADC Conversions with SPU Interrupt Service Routine
• Three Fast 10-bit 500 nsec (rise time) DACs for Servo Loops and Adjustments
• Three 8-bit DACs for Offset Adjustment and Spin Loop
• Bandgap ADC and DAC Midpoint Reference Outputs
• SPU Implemented Spindle Speed Control
• Spindle Interface Logic and Hardware Support for Both CAV and CLV Spindle Control
Modes
• Eight General Purpose I/O Pins
• SPU Servo Control of Focus, Fine Track, Coarse Track and Tray Load Motors
• High-speed Track Counter for Accurate High-speed Track Counts (1.4 MHz when used
with AT78C1503 Read Channel)
• Lower Power Operations with 3.3V Core and 5V Tolerant I/Os
• 8-bit Data and 14-bit Address Controller/Microprocessor Interface
• 3-pin Universal Serial Port Interface to Program Read Channel and Power Devices
• Power Management
• On-chip UART to Access OCDM Unit
www.DataSheet4U.com
DVD/CD Servo
AT78C1502
Description
The Atmel AT78C1502 high-performance servo controller fully integrates all of the
control and demodulation functions for DVD and CD, optical/mechanical systems.
Packaged in 128-lead TQFP and fabricated in 0.35 micron CMOS, the device oper-
ates on a 3.3V logic/analog supply and provides 5V tolerance for digital I/O. An AVR-
based Servo Processing Unit (SPU) embedded in the device provides programmable
control of spindle speed, coarse and fine tracking, focus, sled, draw motor and tilt. The
three parallel programmable AVR microcontrollers in the SPU are the heart of the sys-
tem, offering a range of servo sample rates. With only a 40 MHz system clock, 120
MIPS of processing power is provided. Real-time notch filters can also be calculated.
Fast 10-bit DACs provide real-time control of servo loops and other system adjust-
ments. A universal serial port and many general purpose I/Os are provided.
AVR0 is the master AVR of the three microcontrolloers, communicating with AVR1,
AVR2 and the ARMTDMI in the AT78C1501 interface controller and to the AT78C1503
read channel. An On-Chip Debugger Monitor (OCDM) is offered to enable program-
mers to easily observe theeffect of changes to code on each AVR.
System-level evaluation boards are available with development code in both C and
native code for basic operation of all servos. Simple changes to the code allow any
mechadeck to be interfaced to the AT78C1502.
Rev. 2050A–DVD–07/02
1
1 page  
2050A–DVD–07/02
AT78C1502
Table 1. External Pin Definition (Continued)
www.DataSheet4U.com
Pin #
Symbol
Type
Description
34 TZC
I Track Zero Crossing from Read Channel
35 MIRR
I Mirror Input from Read Channel
36 FOK
I Focus OK Signal from Read Channel
37 HD1,2
I Header 1, 2 Input from Read Channel
38 DGND
P Digital Ground
39 DGND
P Digital Ground
40 HD3,4
I Header 3, 4 Input from Read Channel
41 CNTRST
I TSM Counter Reset Signal
42 SINT
O Servo Interrupt Output to Controller
43 SF
O Servo Fault Output to Controller
44 ADCSTR
O ADC Strobe Output from TSM
45 AVDD
P Analog VDD
46 MUX_OUT
AO Analog MUX Output
47 AIN6
AI Analog Input to MUX
48 AIN5
AI Analog Input to MUX
49 MTRK
AI MUXed Track Track/Hold Input
50 MTRKFB
AI MUXed Track Filter Input
51 AGND
P Analog Ground
52 LPS
AI Lens Position Sensor Track/Hold Input
53 LPS
AI Lens Position Sensor Filter Input
54 FCS
AI Focus Error Signal Track/Hold Input
55 FCSF
AI Focus Error Signal Filter Input
56 AVDD
P Analog VDD
57 SUM
AI Slow Sum Track/Hold Input
58 SUMF
AI Slow Sum Input Filter
59 RDSZ
AI Read Size Input
60 RDSZF
AI Read Size Input Filter
61 N/C
No Connect
62 N/C
No Connect
63 ADCREF
AI Reference I/P for ADC
64 AGND
P Analog GND
65 AGND
P Analog GND
66 N/C
No Connect
67 VBG
AO Bandgap Output Voltage
68 2VBG
AO 2*Bandgap Output Voltage
69 AVDD
P Analog VDD
5
5 Page | ||
| Páginas | Total 9 Páginas | |
| PDF Descargar | [ Datasheet AT78C1502.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AT78C1501 | DVD / CD ATAPI CONTROLLER | ATMEL Corporation |
| AT78C1502 | DVD/CD Servo | ATMEL Corporation |
| AT78C1503 | DVD/CD Read Channel | ATMEL Corporation |
| AT78C1507 | DVD/CD Read Channel | ATMEL Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |