Datasheet.kr   

TS4962M 데이터시트 PDF




STMicroelectronics에서 제조한 전자 부품 TS4962M은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 TS4962M 자료 제공

부품번호 TS4962M 기능
기능 3W filter-free class D audio power amplifier
제조업체 STMicroelectronics
로고 STMicroelectronics 로고


TS4962M 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 41 페이지수

미리보기를 사용할 수 없습니다

TS4962M 데이터시트, 핀배열, 회로
TS4962M
3W filter-free class D audio power amplifier
Features
Operating from VCC = 2.4V to 5.5V
Standby mode active low
Output power: 3W into 4Ω and 1.75W into 8Ω
with 10% THD+N max and 5V power supply.
www.DataSheOeut4tUp.uctopmower: 2.3W @5V or 0.75W @ 3.0V
into 4Ω with 1% THD+N max.
Output power: 1.4W @5V or 0.45W @ 3.0V
into 8Ω with 1% THD+N max.
Adjustable gain via external resistors
Low current consumption 2mA @ 3V
Efficiency: 88% typ.
Signal to noise ratio: 85dB typ.
PSRR: 63dB typ. @217Hz with 6dB gain
PWM base frequency: 250kHz
Low pop & click noise
Thermal shutdown protection
Available in flip-chip 9 x 300μm (Pb-free)
Description
The TS4962M is a differential Class-D BTL power
amplifier. It is able to drive up to 2.3W into a 4Ω
load and 1.4W into a 8Ω load at 5V. It achieves
outstanding efficiency (88%typ.) compared to
classical Class-AB audio amps.
The gain of the device can be controlled via two
external gain-setting resistors. Pop & click
reduction circuitry provides low on/off switch noise
while allowing the device to start within 5ms. A
standby function (active low) allows the reduction
of current consumption to 10nA typ.
Pin connections
IN+
1/A1
GND
2/A2
OUT-
3/A3
VDD
4/B1
VDD
5/B2
GND
6/B3
IN-
STBY
OUT+
7/C1
8/C2
9/C3
IN+: positive differential input
IN-: negative differential input
VDD: analog power supply
GND: power supply ground
STBY: standby pin (active low)
OUT+: positive differential output
OUT-: negative differential output
Block diagram
C2 Stdby Internal
Bias
150k
B1 B2
Vcc
Out+
C3
C1 -
In-
In+ +
A1
PWM
Output
H
Bridge
150k
A3
Out-
Oscillator
GND
A2 B3
Applications
Cellular phone
PDA
Notebook PC
January 2007
Rev 4
1/41
www.st.com
41




TS4962M pdf, 반도체, 판매, 대치품
Application component information
2 Application component information
TS4962M
Table 3. Component information
Component
Functional description
Bypass supply capacitor. Install as close as possible to the TS4962M to
Cs minimize high-frequency ripple. A 100nF ceramic capacitor should be
added to enhance the power supply filtering at high frequency.
Rin
Input resistor to program the TS4962M differential gain (gain = 300kΩ/Rin
with Rin in kΩ).
Input
capacitor
Due to common mode feedback, these input capacitors are optional.
However, they can be added to form with Rin a 1st order high pass filter with
-3dB cut-off frequency = 1/(2*π*Rin*Cin).
www.DataSheet4U.com
Figure 1. Typical application schematics
Vcc
In+
GND
GND
+
Differential
Input
Rin
In- -
Rin
Input
capacitors
are optional
GND
Vcc
C2 Stdby Internal
Bias
150k
B1 B2
Vcc
Cs
1u
Out+
GND
C3
C1 -
In-
In+ +
A1
150k
PWM
Output
H
Bridge
A3
Out-
SPEAKER
Oscillator
GND TS4962
A2 B3
GND
Vcc
In+
GND
GND
+
Differential
Input
Rin
In- -
Rin
Input
capacitors
are optional
GND
Vcc
C2 Stdby Internal
Bias
150k
B1 B2
Vcc
Cs
1u
4 Ohms LC Output Filter
Out+
GND
C3
15µH
C1 -
In-
In+ +
A1
150k
PWM
Output
H
Bridge
A3
Out-
2µF
GND
2µF
15µH
Oscillator
GND TS4962
A2 B3
30µH
GND
1µF
GND
1µF
30µH
8 Ohms LC Output Filter
Load
4/41

4페이지










TS4962M 전자부품, 판매, 대치품
TS4962M
Electrical characteristics
Table 5.
Symbol
VCC = +4.2V, GND = 0V, VIC = 2.5V, Tamb = 25°C (unless otherwise specified)(1)
Parameter
Conditions
Min. Typ. Max.
ICC
ISTBY
VOO
Supply current
Standby current (2)
Output offset voltage
Pout Output power
THD + N
Total harmonic
distortion + noise
www.DataSheet4U.com
Efficiency Efficiency
PSRR
Power supply
rejection ratio with
inputs grounded (3)
No input signal, no load
No input signal, VSTBY = GND
No input signal, RL = 8Ω
G=6dB
THD = 1% max, F = 1kHz, RL = 4Ω
THD = 10% max, F = 1kHz, RL = 4Ω
THD = 1% max, F = 1kHz, RL = 8Ω
THD = 10% max, F = 1kHz, RL = 8Ω
Pout = 600mWRMS, G = 6dB, 20Hz < F < 20kHz
RL = 8Ω + 15µH, BW < 30kHz
Pout = 700mWRMS, G = 6dB, F = 1kHz,
RL = 8Ω + 15µH, BW < 30kHz
Pout = 1.45WRMS, RL = 4Ω +≥ 15µH
Pout =0.9WRMS, RL = 8Ω+≥ 15µH
F = 217Hz, RL = 8Ω, G=6dB,
Vripple = 200mVpp
2.1 3
10 1000
3 25
1.6
2
0.95
1.2
1
0.35
78
88
63
CMRR
Common mode
rejection ratio
Gain Gain value
F = 217Hz, RL = 8Ω, G = 6dB,
ΔVicm = 200mVpp
Rin in kΩ
57
-2---7---3----k----Ω--
Rin
3----0---0----k---Ω---
Rin
-3---2---7----k---Ω---
Rin
RSTBY
Internal resistance
from Standby to GND
273 300 327
FPWM
Pulse width modulator
base frequency
180 250 320
SNR
tWU
tSTBY
Signal to noise ratio
Wake-uptime
Standby time
A-weighting, Pout = 0.9W, RL = 8Ω
85
5 10
5 10
Unit
mA
nA
mV
W
%
%
dB
dB
V/V
kΩ
kHz
dB
ms
ms
7/41

7페이지


구       성 총 41 페이지수
다운로드[ TS4962M.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
TS4962

2.8W filter-free mono class D audio power amplifier

STMicroelectronics
STMicroelectronics
TS4962M

3W filter-free class D audio power amplifier

STMicroelectronics
STMicroelectronics

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵