|
|
PDF BH1710FVC Data sheet ( Hoja de datos )
| Número de pieza | BH1710FVC | |
| Descripción | Digital 16bit Serial Output Type Ambient Light Sensor IC | |
| Fabricantes | ROHM Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de BH1710FVC (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Ambient Light Sensor ICs
Digital 16bit Serial Output Type
Ambient Light Sensor IC
BH1710FVC
No.10046EBT07
●Descriptions
BH1710FVC is an digital Ambient Light Sensor IC for I2C bus interface. This IC is the most suitable to obtain the ambient
light data for adjusting LCD and Keypad backlight power of Mobile phone. It is possible to detect wide range at High
resolution. (1 - 65535 lx).
●Features
1) I2C bus Interface (f / s Mode Support)
2) Spectral responsibility is approximately human eye response
3) Illuminance to Digital Converter
4) Wide range and High resolution. (1 – 65535 lx)
5) Low Current by power down function
6) 50Hz / 60Hz Light noise reject-function
7) 1.8V Logic input interface
8) No need any external parts
9) Light source dependency is little. (ex. Incandescent Lamp. Fluorescent Lamp. Halogen Lamp. White LED. Sun Light)
10) It is possible to select 2 type of I2C slave-address.
11) Adjustable measurement result for influence of optical window
(It is possible to detect min. 0.24 lx, max. 100000 lx by using this function.)
●Applications
Mobile phone, LCD TV, NOTE PC, Portable game machine, Digital camera, Digital video camera, Car navigation, PDA,
LCD display
●Absolute Maximum Ratings
Parameter
Symbol
Ratings
Units
Supply Voltage
Vmax
4.5 V
Operating Temperature
Topr
-30～85
℃
Storage Temperature
Tstg
-40～100
℃
SDA Sink Current
Imax
7 mA
Power Dissipation
Pd 260※
※ 70mm × 70mm × 1.6mm glass epoxy board. Derating in done at 3.47mW/℃ for operating above Ta=25℃.
mW
●Operating Conditions
Parameter
VCC Voltage
I2C Reference Voltage
Symbol
VCC
VDVI
Min.
Ratings
Typ.
Max.
Units
2.4 3.0 3.6 V
1.65
－
VCC
V
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
1/16
2010.06 - Rev.B
1 page  
BH1710FVC
●Instruction Set Architecture
Instruction
Power Down
Opecode
0000_0000 No active state.
Technical Note
www.DataSheet4U.com
Comments
Power On
0000_0001 Waiting for measurement command.
Reset
0000_0111
Reset Data register value. Reset command is not acceptable in
Power Down mode.
Continuously H-Resolution Mode
0001_0000
Start measurement at 1lx resolution.
Measurement Time is typically 120ms.
Continuously M-Resolution Mode
0001_0011
Start measurement at 4lx resolution.
Measurement Time is typically 16ms.
Continuously L-Resolution Mode
One Time H-Resolution Mode
One Time M-Resolution Mode
One Time L-Resolution Mode
Change Measurement time
(High bit)
0001_0110
Start measurement at 32lx resolution.
Measurement Time is typically 2.9ms.
0010_0000
0010_0011
0010_0110
Start measurement at 1lx resolution.
Measurement Time is typically 120ms.
It is automatically set to Power Down mode after measurement.
Start measurement at 4lx resolution.
Measurement Time is typically 16ms.
It is automatically set to Power Down mode after measurement.
Start measurement at 32lx resolution.
Measurement Time is typically 2.9ms.
It is automatically set to Power Down mode after measurement.
010_MT[9,8,7,6,5] Change measurement time.
※ Please refer "adjust measurement result for influence of optical window."
Change Measurement time
(Low bit)
※ Don't input the other opecode.
011_MT[4,3,2,1,0] Change measurement time.
※ Please refer "adjust measurement result for influence of optical window."
●Measurement mode explanation
Measurement Mode
H-Resolution Mode
M-Resolution Mode
L-Resolution Mode
Measurement Time.
Typ. 120ms.
Typ. 16ms.
Typ. 2.9ms.
Resolution
1 Lx.
4 Lx.
32 Lx.
We recommend to use H-Resolution Mode.
Measurement time (integration time) of H-Resolution Mode is so long that some kind of noise(including in 50Hz / 60Hz noise)
is rejected. And H-Resolution Mode is 1 l x resolution so that it is suitable for darkness (less than 10 lx)
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
5/16
2010.06 - Rev.B
5 Page 
BH1710FVC
Technical Note
www.DataSheet4U.com
●Adjust measurement result for influence of optical window. (sensor sensitivity adjusting )
BH1710FVC is possible to change sensor sensitivity. And it is possible to cancel the optical window influence (difference with
/ without optical window) by using this function. Adjust is done by changing measurement time. For example, when
transmission rate of optical window is 50% (measurement result becomes 0.5 times if optical window is set), influence of
optical window is ignored by changing sensor sensitivity from default to 2 times
Sensor sensitivity is shift by changing the value of MTreg (measurement time register). MTreg value has to set 2 times if
target of sensor sensitivity is 2 times. Measurement time is also set 2 times when MTreg value is changed from default to 2
times.
ex) Procedure for changing target sensor sensitivity to 2 times.
Please change Mtreg from ” 01_0010_1100” ( default ) to ” 10_0101_1000” ( default * 2 ).
1)Changing High bit of Mtreg
ST Slave Address
R/W
0
Ack
010_10010
Ack SP
2)Changing Low bit of Mtreg
ST Slave Address
R/W
0
Ack
011_11000
Ack SP
3)Input Measurement Command.
ST Slave Address
R/W
0
Ack
0001_0000
Ack SP
※This example is High Resolution mode, but it accepts the other measurement.
4)After about 240ms, measurement result is registered to Data Register. (High Resolution mode is typically 120ms, but
measurement time is set twice.)
The below table is seeing the changeable range of MTreg.
Min.
Changeable
Binary
00100_01100
(sensitivity : default*0.47)
range of Mtreg
Decimal
140
(sensitivity : default*0.47)
Typ.
01001_01100
default
300
default
Max.
11111_11110
(sensitivity : default*3.41)
1022
(sensitivity : default*3.41)
It is possible to detect 0.24lx by using this function at H-resolution mode.
The below formula is to calculate illuminance per 1 count.
Illuminance per 1 count ( lx / count ) = 1 / 1.2 *( 300 / X )
1.2 : Measurement accuracy
300 : Default value of MTreg
X : Mtreg value
The below table is seeing the detail of resolution.
Mtreg value
00100_01100
01001_01100
11111_11110
lx / count
1.79
0.83
0.24
Please input the opecode at PowerDown state to change Mtreg.There is a possibility of malfunctioning when the opecode to
change Mtreg is input while the illuminance measurement is going .
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
11/16
2010.06 - Rev.B
11 Page | ||
| Páginas | Total 17 Páginas | |
| PDF Descargar | [ Datasheet BH1710FVC.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| BH1710FVC | Digital 16bit Serial Output Type Ambient Light Sensor IC | ROHM Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |