|
|
|
부품번호 | SH063Mxxxxxxx-xxxx 기능 |
|
|
기능 | Aluminum Electrolytic Capacitors | ||
제조업체 | YAGEO | ||
로고 | |||
YAGEO Corporation
Date: 04/15/2009
Aluminum Electrolytic Capacitors
File : 2060
Engineering Bulletin for SH Type
Page: 1/25
______________________________________________________________________________________
SH Type
+105ºC Single-ended lead aluminum electrolytic capacitors for the rated voltage up to 450 V.
. Long life for 105ºC, 2000 hrs, suited for high quality and high reliability demander.
. High CV product, the dimension are as same as SEK series for under 100WV.
Diagram of Dimensions (Unit = mm)
Vinyl Sleeve
Rubber End Seal
dψ
F ±0.5
L
15 Min 5 Min
D +0.5
L≦ 16 :
L > 16 :
Dψ=8 & 10:
L+1.5max
L+2max
L+2.5max
Dψ< 20 : Dψ+0.5
Dψ≧ 20 : Dψ+1
D ψ 5.0 6.0 8.0 10.0 12.0 13.0 16.0 18.0
F 2.0 2.5 3.5
5.0
7.5
d ψ 0.5
0.6 0.8
22.0
10.0
0.8
www.DataSheet.in
YAGEO Corporation
Date: 04/15/2009
Aluminum Electrolytic Capacitors
File : 2060
Engineering Bulletin for SH Type
Page: 4/25
______________________________________________________________________________________
PERFORMANCE CHARACTERISTICS (continued)
1. General Characteristics
1.1 Marking
Capacitors shall be marked with YAGEO mark ; rated capacitance ; rated DC working voltage range.
and the date code of manufacture. The cathode lead will be identified with minus signs (-) on the side of
the case.
1.2 Operating Temperature Range
These capacitors are designed to operate over a temperature range of -40ºC to +105ºC, for the rated
voltage up to 450 V.
1.2.1 At -40ºC, capacitors shall retain at least 70% of their original 20ºC measured capacitance. At +85ºC.
capacitance shall increases to no more than 120% of their original 20ºC measured capacitance.
1.2.2 At -40(-25) ºC, impedance shall increase to no more than the following table.
TEMPERATURE CHARACTERISTIC (@ 120Hz)
Working Voltage (WV)
6.3 10 16 25 35-100 160-250 315-450
---------------------------------------------------------------------------------------------------------------
Impedance Z-25ºC/ Z+20ºC 4
322
2
4
4
Impedance Z-40ºC/ Z+20ºC 8
643
3
6
8
1.3 Vent Test (applies only to those capacitors with vents.)
During and after the applicable test below (1.3.1 or 1.3.2.) there shall be no explosion, flash, flame or
expulsion of particles of the core or container. In addition, the case shall not be expelled from the core.
If the capacitor under test is a multisection unit, this test shall apply to the input section only.
1.3.1 AC Test. Capacitors with DC Rating Over 100 Volts
The capacitor under test shall be connected to a 120 volt MS 60Hz, 100 ampere service through a 30
ampere thermal breaker and a 0.5 ohm, low inductance, series resistor. The capacitor shall be connected
to this circuit for 5 minutes after the initial setting of the breaker or until the breaker has opened 3 times.
lf the breaker opens, it shall be reset not sooner than 30 seconds nor longer than 60 seconds from the
time it opened.
1.3.2 DC Test. Capacitors with DC Rating 100 Volts or Less
Both of the following tests shall be performed, but on separate test units.
1.3.2.1 Forward Bias Test.
The capacitor under test shall be connected to a DC power supply that has sufficient voltage to supply a
constant direct current of 500 milliamperes with the positive terminal of the capacitor connected to the
positive supply terminal and the negative capacitor terminal connected to the negative supply terminal.
The constant current shall be maintained until (1) the capacitor vents, (2) 300 seconds have elapsed, or
(3) the capacitor under test open circuits.
www.DataSheet.in
4페이지 YAGEO Corporation
Date: 04/15/2009
Aluminum Electrolytic Capacitors
File : 2060
Engineering Bulletin for SH Type
Page: 7/25
______________________________________________________________________________________
GUIDE TO APPLICATION
1. Maximum Ripple Current
1.1 Maximum rms. ripple current at 105ºC 120 Hz is given in the table 1.
1.2 When capacitors are operated at temperatures other than 105ºC, and frequency other than 120 Hz, the
maximum rms. ripple currents must be multiplied by the factors shown in below table.
COMPENSATION FACTOR OF RIPPLE CURRENT VERSUS FREQUENCY
WV. CAP(uF)
50 120 300 1K 10K-100K (Hz)
---------------------------------------------------------------------------------------
6.3-100V Below - 68μF 0.75 1 1.3 1.57
2.00
6.3-100V 69 - 470μF
0.80 1 1.23 1.34
1.50
6.3-100V 471 - 22000μF 0.85 1 1.10 1.13
1.15
160-450V All Cap(μF) 0.80 1 1.25 1.40
1.60
2. Ripple voltage
Ripple voltage must not exceed the following:
The sum of the DC voltage plus the AC ripple voltage must not exceed the rated DC voltage. The DC
voltage plus the peak AC voltage must not cause a voltage reversal more than 1.5 volts.
3. Insulating
General types of aluminum electrolytic capacitors are covered with a vinyl sleeve or the like. And this
sleeve is used for marking. When the internal element or the container is needed to be insulated,
capacitors specially designed for insulation requirement are recommended to be used.
4. Soldering
4-1 When soldering a printed circuit board with various components, too high soldering temperature or too
long dipping times may cause secondary shrinking of the sleeve which unnecessarily exposes the
container. Soldering is allowed to performed at less than 260ºC for less than 10 seconds.
4-2 Soldering may melt or break the sleeve,if the sleeve is contacted with circuit patterns. To avoid this
trouble, the capacitors are recommended to be slightly apart from the circuit boards.
www.DataSheet.in
7페이지 | |||
구 성 | 총 25 페이지수 | ||
다운로드 | [ SH063Mxxxxxxx-xxxx.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
SH063Mxxxxxxx-xxxx | Aluminum Electrolytic Capacitors | YAGEO |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |