|
|
|
부품번호 | W78LE52 기능 |
|
|
기능 | 8-BIT MICROCONTROLLER | ||
제조업체 | Winbond | ||
로고 | |||
전체 26 페이지수
W78LE52/W78L052A
8-BIT MICROCONTROLLER
Table of Contents-
1. GENERAL DESCRIPTION ............................................................................................................... 2
2. FEATURES....................................................................................................................................... 2
3. PIN CONFIGURATIONS .................................................................................................................. 3
4. PIN DESCRIPTION .......................................................................................................................... 4
5. FUNCTIONAL DESCRIPTION ......................................................................................................... 5
5.1 Eight-source interrupt information: .......................................................................................... 6
6. ON-CHIP FLASH EPROM CHARACTERISTICS .......................................................................... 10
7. SECURITY BITS............................................................................................................................. 12
8. ABSOLUTE MAXIMUM RATINGS ................................................................................................. 13
9. DC CHARACTERISTICS................................................................................................................ 14
10. AC CHARACTERISTICS................................................................................................................ 16
11. TIMING WAVEFORMS................................................................................................................... 19
12. TYPICAL APPLICATION CIRCUITS.............................................................................................. 22
13. PACKAGE DIMENSIONS............................................................................................................... 24
14. REVISION HISTORY...................................................................................................................... 26
www.DataSheet.in
Publication Release Date: November 6, 2006
- 1 - Revision A6
W78LE52/W78L052A
4. PIN DESCRIPTION
SYMBOL
DESCRIPTIONS
EXTERNAL ACCESS ENABLE: This pin forces the processor to execute out of
external ROM. It should be kept high to access internal ROM. The ROM address and
EA data will not be presented on the bus if EA pin is high and the program counter is within
on-chip ROM area.
PSEN
ALE
RST
XTAL1
PROGRAM STORE ENABLE: PSEN enables the external ROM data onto the Port 0
address/ data bus during fetch and MOVC operations. When internal ROM access is
performed, no PSEN strobe signal outputs from this pin.
ADDRESS LATCH ENABLE: ALE is used to enable the address latch that separates
the address from the data on Port 0.
RESET: A high on this pin for two machine cycles while the oscillator is running resets
the device.
CRYSTAL1: This is the crystal oscillator input. This pin may be driven by an external
clock.
XTAL2 CRYSTAL2: This is the crystal oscillator output. It is the inversion of XTAL1.
VSS GROUND: Ground potential
VDD POWER SUPPLY: Supply voltage for operation.
PORT 0: Port 0 is a bi-directional I/O port which also provides a multiplexed low order
P0.0−P0.7 address/data bus during accesses to external memory. The Port 0 is also an open-drain
port and external pull-ups need to be connected while in programming.
PORT 1: Port 1 is a bi-directional I/O port with internal pull-ups. The bits have alternate
functions which are described below:
P1.0−P1.7 T2(P1.0): Timer/Counter 2 external count input
T2EX(P1.1): Timer/Counter 2 Reload/Capture control
P2.0−P2.7
PORT 2: Port 2 is a bi-directional I/O port with internal pull-ups. This port also provides
the upper address bits for accesses to external memory.
PORT 3: Port 3 is a bi-directional I/O port with internal pull-ups. All bits have alternate
functions, which are described below:
RXD(P3.0) : Serial Port receiver input
TXD(P3.1) : Serial Port transmitter output
INT0 (P3.2) : External Interrupt 0
P3.0−P3.7 INT1(P3.3) : External Interrupt 1
T0(P3.4) : Timer 0 External Input
T1(P3.5) : Timer 1 External Input
WR (P3.6) :External Data Memory Write Strobe
RD (P3.7) : External Data Memory Read Strobe
PORT 4: Another bit-addressable bidirectional I/O port P4. P4.3 and P4.2 are alternative
P4.0−P4.3 function pins. It can be used as general I/O port or external interrupt input sources
(INT2 /INT3 ).
www.DataSheet.in
-4-
4페이지 W78LE52/W78L052A
4. Power-off Flag
***PCON - Power control (87H)
---
POF GF1 GF0
PD
IDL
POF:
Power off flag. Bit is set by hardware when power on reset. It can be cleared by software
to determine chip reset is a warm boot or cold boot.
GF1, GF0: These two bits are general-purpose flag bits for the user.
PD: Power down mode bit. Set it to enter power down mode.
IDL: Idle mode bit. Set it to enter idle mode.
The power-off flag is located at PCON.4. This bit is set when VDD has been applied to the part. It can
be used to determine if a reset is a warm boot or a cold boot if it is subsequently reset by software.
Watchdog Timer
The Watchdog timer is a free-running timer which can be programmed by the user to serve as a
system monitor, a time-base generator or an event timer. It is basically a set of dividers that divide the
system clock. The divider output is selectable and determines the time-out interval. When the time-out
occurs a system reset can also be caused if it is enabled. The main use of the Watchdog timer is as a
system monitor. This is important in real-time control applications. In case of power glitches or electro-
magnetic interference, the processor may begin to execute errant code. If this is left unchecked the
entire system may crash. The watchdog time-out selection will result in different time-out values
depending on the clock speed. The Watchdog timer will de disabled on reset. In general, software
should restart the Watchdog timer to put it into a known state. The control bits that support the
Watchdog timer are discussed below.
Watchdog Timer Control Register
Bit: 7 6 5
ENW CLRW WIDL
4
-
3210
- PS2 PS1 PS0
Mnemonic: WDTC
Address: 8FH
ENW : Enable watch-dog if set.
CLRW : Clear watch-dog timer and prescaler if set. This flag will be cleared automatically
WIDL : If this bit is set, watch-dog is enabled under IDLE mode. If cleared, watch-dog is disabled
under IDLE mode. Default is cleared.
PS2, PS1, PS0: Watch-dog prescaler timer select. Prescaler is selected when set PS2−0 as follows:
www.DataSheet.in
Publication Release Date: November 6, 2006
- 7 - Revision A6
7페이지 | |||
구 성 | 총 26 페이지수 | ||
다운로드 | [ W78LE52.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
W78LE51 | 8-BIT MTP MICROCONTROLLER | Winbond |
W78LE51 | 8-BIT MICROCONTROLLER | Winbond |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |