DataSheet.es    


PDF L5950 Data sheet ( Hoja de datos )

Número de pieza L5950
Descripción MULTIPLE MULTIFUNCTION VOLTAGE REGULATOR FOR CAR RADIO
Fabricantes STMicroelectronics 
Logotipo STMicroelectronics Logotipo



Hay una vista previa y un enlace de descarga de L5950 (archivo pdf) en la parte inferior de esta página.


Total 8 Páginas

No Preview Available ! L5950 Hoja de datos, Descripción, Manual

® L5950
MULTIPLE MULTIFUNCTION
VOLTAGE REGULATOR FOR CAR RADIO
5 REGULATORS
10V (350mA); 8.5V (175mA); 5V (350mA); 5V
(250mA); 8V/10V (1A)
ALL REGULATORS ARE LOW DROPOUT
OUPUTS
3 HIGH SIDE DRIVERS:
2A (HSD1), 0.45A (HSD2 & HSD3)
NO EXTERNAL CHARGE PUMP CAPACI-
TORS ARE REQUIRED
STAND BY MODE CONTROLLED BY 3 IN-
PUT PINS:
ENABLE FOR REG2 AND REG3,
I2C BUS FOR REG1, REG4, REG5, HSD1,
HSD2, HSD3
INDIVIDUAL THERMAL SHUTDOWN
INDEPENDENT CURRENT LIMITING
SHORT CIRCUIT PROTECTION
LOAD DUMP PROTECTION AND OVERVOL-
TAGE SHUTDOWN
ESD PROTECTED
BLOCK DIAGRAM
BAT
GND
VOLTAGE
REFERENCE
VREF
ENABLE
SCL
SDA
8.5 & 5V
ENABLE
PC OUTPUT
CONTROL
CURRENT
LIMIT
PROTECTION
LOGIC
INDIVIDUAL
THERMAL
SHUTDOWN
OVERVOLTAGE
PROTECTION
March 2001
Multiwatt15
DESCRIPTION
The ASPM (Audio System Power Module) is an
integration of three high side drivers and five
regulators developed to provide the power for an
audio system.
The outputs of the IC are controlled via the I2C
bus and the Enable input.
External protection must be provided for reverse
battery protection.
REG 1
10V 350mA
REG 2
8.5V 175mA
REG 3
5V 350mA
REG 4
8V/10V 1A
REG 5
5V 250mA
REG1
REG2
REG3
REG4
REG5
DRIVE 1
2A
HSD1
DRIVE 2
450mA
HSD2
DRIVE 3
450mA
HSD3
D99AU1002
1/8

1 page




L5950 pdf
L5950
ELECTRICAL CHARACTERISTICS (continued)
Symbol
Parameter
CHARACTERISTICS FOR I2C
VIL LOW Level Input Voltage
VIH HIGH Level Input Voltage
VHYS
Input Hysteresis
VOL1
LOW Level Output
Test Condition
Sink Current = 3mA
VOL2
II
fSCL
Input Current
SCL Clock Frequency
Sink Current = 6mA
0.4V VI 0.9VDDmax
Min. Typ. Max. Unit
1.5 V
3V
0.2 V
0.4 V
0.6 V
-10 10 µA
400 kHz
FUNCTIONAL DESCRIPTION
The three high side drivers are a 2.0A output
(HSD1), and two 450mA outputs (HSD2 & 3). The
five regulator outputs are a 10V at 350mA
(REG1), an 8.5V at 175mA (REG2), a 5V at
350mA (REG3), an 8V/10V at 1A (REG4), and 5V
at 250mA (REG5). The regulators are low drop-
out. The regulators will operate with output ca-
pacitors with ESR of 0.1to 5.
The 8.5V regulator output (REG2) is a tighter tol-
erance output than the other regulator outputs.
The 8.5V output is a ±2.5% (5% total range) out-
put over temperature. This is required on the
regulator to improve performance and reduce
cost on the 8.5V driven IC’s in the radio. The
tighter tolerance is possible by performing a trim
of the bandgap reference to the 8.5V output. The
other outputs are ±5% variation over temperature.
REG3 is referenced from the VREF input not the
internal bandgap. This is done to minimize the
voltage offset between individual 5V supplies.
The REG2 and REG3 outputs are turned on and
off with the Enable input, a ’1’ turns the outputs on
and a ’0’ turns them off. When Enable is "1", the
other outputs can be independently controlled via
the I2C bus. When a given regulator is turned off it
must be guaranteed to be lower than 0.2V. The
output voltage of REG4 is selected via bit 5 of the
I2C data byte: 8V is the output voltage if bit5 = ’0’
Figure 1. Definition of Timing on the I2C Bus.
while 10V is the output voltage when bit5 = ’1’.
When all outputs are turned off the total current
draw must be minimized. I2C will run at a clock
speed range of 100kHz to 400kHz. This device
should be capable of operating at any frequency
within this range.
Protection
The L5950 can survive under the following condi-
tions: shorting the outputs to BAT and GND, loss
of BAT, loss of IC GND, double battery(+26.5V),
4000V ESD, 34V load dump. L5950 will not han-
dle a reverse battery condition. External compo-
nents must be implemented for reverse battery
protection.
Thermal Shutdown: REG1, REG2, REG3, REG4,
REG5 outputs shutdown at 160°C and return to
normal operation at 130°C. The HSD2 and HSD3
shutdown at 160°C and return to normal opera-
tion at 130°C. The HSD1 with go into thermal
shutdown at 170°C and returns to operation at
120°C.
Current Limiting: each voltage regulator will con-
tain its own current protection.
Short Circuit: If the outputs are short circuited, the
IC will go into current limiting and eventually the
thermal shutdown will kick in. Current limiting will
not disable the outputs.
Overvoltage: The IC will not operate if the BAT
voltage reaches 27V typ. or above.
SDA
tBUP
SCL
P
S
tLOW
tR
tHD;DAT
tHD;DAT
tHIGH
tF
tHD;STA
tSP
tSU;DAT
tSU;STA
Sr
D99AU1007
tSU;STO
P
5/8

5 Page










PáginasTotal 8 Páginas
PDF Descargar[ Datasheet L5950.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
L5950MULTIPLE MULTIFUNCTION VOLTAGE REGULATOR FOR CAR RADIOSTMicroelectronics
STMicroelectronics
L5951TRIPLE OUTPUT MULTIFUNCTION VOLTAGE REGULATOR FOR CAR RADIO WITH IDR/CLASS 2 INTERFACESTMicroelectronics
STMicroelectronics
L5952MULTIPLE MULTIFUNCTION VOLTAGE REGULATORSTMicroelectronics
STMicroelectronics
L5953Multiple switching voltage regulatorSTMicroelectronics
STMicroelectronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar