|
|
Número de pieza | HKTX179S | |
Descripción | FIBER OPTIC TRANSMITTING MODULE | |
Fabricantes | GOOD TAKE | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de HKTX179S (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
No Preview Available ! www.DataSheet.co.kr
GOOD TAKE
HKTX179S
FIBER OPTIC TRANSMITTING MODULE
FEATURES
1) Conform to EIAJ standard CP-1201 (For Digital audio interfaces including fiber optic inter-connections).
2) TTL interface.
3) LED is driven by differential circuit.
4) +5V single power supply.
5) High speed signal transmission (12.5M NRZ signal).
6) ESD tolerance IC > 8KV.
7) Standard package (panel mount type).
APPLICATIONS
1) Digital audio equipment: CD, MD and DVD player to sound applications for personal computers and computer
entertainment systems.
2) Navigation system.
ABSOLUTE MAXIMUM RATINGS (Ta=25 oC)
Characteristic
Symbol
Rating
Supply Voltage
Vcc -0.5 to +7
Input Voltage
VIN -0.5 to Vcc+0.5
Operating Temperature
Topr
-20 to +70
Storage Temperature
Tstg -30 to +80
*Soldering Temperature
Tsol
260
* T=5sec
Units
V
V
oC
OC
OC
1/5
09/07/2005 REV.1.1
Datasheet pdf - http://www.DataSheet4U.net/
1 page www.DataSheet.co.kr
GOOD TAKE
BLOCK DIAGRAM
HKTX179S
Vcc
TTL
IN
BUFFER
AMP
LED
DRIVER
PRECAUTIONS DURING INSTALLATION
1) Fixing fiber optical transceiving module
Insert the fiber optic transmitting module HKTX179S into the printed circuit board to fix the module to the board.
¡Solder the fixed pin at 260 or less within 5 seconds.
2) Soldering
Optical modules use semiconductor devices internally. However, in principle, optical modules are optical components.
At soldering, take care that flux dose not contact the emitting surface or detecting surface. Also take care at flux
removal after soldering. Some optical modules come with protective cap. The protective cap is used to avoid
malfunction when the optical module is not in use. Note that it is not dust or waterproof.
As mentioned before, optical modules are optical component. Thus, in principle, soldering where there may be flux
residue or flux removal after soldering is not recommended. GOOD TAKE recommends that soldering be performed
without the optical module mounted on the board. Then, after the board is cleaned, solder the optical module manually.
Do not perform any further cleaning. If the optical module cannot be soldered manually, use non-halogen (chlorine-
free) flux and make sure, without cleaning, there is no residue such as chlorine. This is one of the ways to eliminate the
effects of flux. In such a case, check the reliability.
3) Solvent
When using solvent for flux removal, do not use a high acid or high alkali solvent. Be-careful not to pour solvent in the
optical connector ports. If solvent is inadvertently poured there, clean with cotton tips.
4) Protective cap
When the fiber optic transmitting module HKTX179S is not in use, use the protective cap.
5) Input voltage
If a voltage exceeding the maximum rating value (Vcc+0.5V) is applied to the transmitter Input, the internal IC may
degrade causing some damage. If excessive voltage due to surge may be added to the input, insert a protective circuit.
5/5
09/07/2005 REV.1.1
Datasheet pdf - http://www.DataSheet4U.net/
5 Page |
Páginas | Total 5 Páginas | |
PDF Descargar | [ Datasheet HKTX179S.PDF ] |
Número de pieza | Descripción | Fabricantes |
HKTX179S | FIBER OPTIC TRANSMITTING MODULE | GOOD TAKE |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |