|
|
PDF LV56081GP Data sheet ( Hoja de datos )
| Número de pieza | LV56081GP | |
| Descripción | Charge Pump Power Supply | |
| Fabricantes | Sanyo Semicon Device | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LV56081GP (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
www.DataSheet.co.kr
Ordering number : ENA1499
LV56081GP
Bi-CMOS LSI
For CCD
Charge Pump Power Supply
Overview
The LV56081GP is charge pump power supply for CCD.
Functions
• The charge pump boosts the +3.3V input by multiplying with +6, then by -3 to regulate the voltage to the specified level.
• The output voltage is +15V, -5.5V necessary for CCD.
• Soft start function incorporated, which reduces the inrush current at start of charge pump.
• Short-circuit protection function incorporated.
• Four types of operating frequency selectable.
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage
Allowable power dissipation
Operating temperature
Storage temperature
Symbol
VDD max
Pd max
Topr
Tstg
Conditions
with specified substrate *1
*1 : Specified substrate : 40mm × 50mm × 0.8mm, glass epoxy board
Ratings
3.5
0.8
-20 to +80
-40 to +125
Unit
V
W
°C
°C
Allowable Operating Ratings at Ta = 25°C, PGND = 0V
Parameter
Symbol
Conditions
Supply voltage
Input CLK frequency
VDD
CKIN
SEL=H *2
Input High voltage
Input Low voltage
VINH
VINL
EN pin
EN pin
*2 : Note that the charge pump frequency should be adjusted with S0/S1 so that it becomes 2MHz or less.
min
3.0
0.1
0.7VDD
-0.1
Ratings
typ
3.3
max
3.45
8
VDD
0.4
Unit
V
MHz
V
V
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer's products or
equipment.
61009 MS 20061207-S00003 No.A1499-1/7
Datasheet pdf - http://www.DataSheet4U.net/
1 page  
www.DataSheet.co.kr
LV56081GP
Short-circuit Protection
VH and VL output pins incorporate the short-circuit protection function.
When the output pins are short-circuited to allow the large current to flow, IC is latched OFF to interrupt output.
To reset from the interrupted state, set the EN pin to L, then reset it again to H.
Frequency Selection
The charge pump operating frequency can be changed with S0 and S1
logics.
For light load, the reactive load can be reduced by lowering the
operating frequency.
SEL logic also enables synchronous operation with external CLK.
The charge pump is operated with the frequency equivalent to 1/2 of
input CLK.
(The IC internal oscillator is used for the sequence, so that it is
normally ON regardless of SEL.
S0 S1
LL
HL
LH
HH
CP operating frequency
SEL=L
SEL=H
1MHz
1/2 CLK
500kHz
250kHz
1/4 CLK
1/8 CLK
125kHz
1/16 CLK
For minimum 9.4ms after startup with the EN signal set to H, the IC
internal clock is used to operate the charge pump with 1 MHz regardless
of the input of SEL, S0, and S1 pins. After the 9.4ms(min) period, the
charge pump frequency is changed over according to the state of SEL,
S0, and S1 pins. The changeover frequency is set as shown in the table
right.
SEL
L IC internal oscillator
H Synchronous operation with external CLK
Internal Equivalent Circuit
S0 pin
S1 pin
SEL pin
CLK pin
DQ
Q
Internal
1MHz
VH regulator start
signal
L ⇒ H in 9.4ms (min) after EN = H
B DQ
Y
A
Q
2-input multiplexer
Truth Table
SEL Y
LA
HB
clk
clk/2
clk/4
clk/8
Y
Charge pump
clock
4-input multiplexer
DQ
DQ
Q Q Truth Table
S0 S1 Y
L L clk
H L clk/2
L H clk/4
H H clk/8
External signal input pin
Internal signal
No.A1499-5/7
Datasheet pdf - http://www.DataSheet4U.net/
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet LV56081GP.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LV56081GP | Charge Pump Power Supply | Sanyo Semicon Device |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |