MR-E-70A-KH003 PDF 데이터시트 ( Data , Function )

부품번호 MR-E-70A-KH003 기능
기능 General-Purpose AC Servo

이 페이지 하단에 미리보기 및 MR-E-70A-KH003 다운로드 (pdf 파일) 링크가 있습니다.

전체 70 페이지

No Preview Available !

MR-E-70A-KH003 데이터시트, 핀배열, 회로
General-Purpose AC Servo
General-Purpose Interface
MR-E- A-KH003
MR-E- AG-KH003
Datasheet pdf -

MR-E-70A-KH003 pdf, 반도체, 판매, 대치품
4. Additional instructions
The following instructions should also be fully noted. Incorrect handling may cause a fault, injury, electric
shock, etc.
(1) Transportation and installation
Transport the products correctly according to their weights.
Stacking in excess of the specified number of products is not allowed.
Do not carry the servo motor by the cables, shaft or encoder.
Do not hold the front cover to transport the servo amplifier. The servo amplifier may drop.
Install the servo amplifier in a load-bearing place in accordance with the Instruction Manual.
Do not climb or stand on servo equipment. Do not put heavy objects on equipment.
The servo amplifier and servo motor must be installed in the specified direction.
Leave specified clearances between the servo amplifier and control enclosure walls or other equipment.
Do not install or operate the servo amplifier and servo motor which has been damaged or has any parts
Provide adequate protection to prevent screws and other conductive matter, oil and other combustible
matter from entering the servo amplifier and servo motor.
Do not drop or strike servo amplifier or servo motor. Isolate from all impact loads.
When you keep or use it, please fulfill the following environmental conditions.
In [
operation [
In storage [
In operation
In storage
Servo amplifier
Servo motor
0 to 55 (non-freezing)
0 to 40 (non-freezing)
32 to 131 (non-freezing)
32 to 104 (non-freezing)
20 to 65 (non-freezing)
15 to 70 (non-freezing)
4 to 149 (non-freezing)
5 to 158 (non-freezing)
90 RH or less (non-condensing)
80 RH or less (non-condensing)
90 RH or less (non-condensing)
Indoors (no direct sunlight) Free from corrosive gas, flammable gas, oil mist, dust and dirt
Max. 1000m above sea level
HF-KE W1-S100 X Y : 49
5.9 or less
HF-SE52JW1-S100 to
X Y : 24.5
X : 24.5
Y : 49
Note. Except the servo motor with reduction gear.
Securely attach the servo motor to the machine. If attach insecurely, the servo motor may come off during
The servo motor with reduction gear must be installed in the specified direction to prevent oil leakage.
Take safety measures, e.g. provide covers, to prevent accidental access to the rotating parts of the servo
motor during operation.
Never hit the servo motor or shaft, especially when coupling the servo motor to the machine. The encoder
may become faulty.
Do not subject the servo motor shaft to more than the permissible load. Otherwise, the shaft may break.
A- 3
Datasheet pdf -


MR-E-70A-KH003 전자부품, 판매, 대치품
(6) Storage for servo motor
Note the following points when storing the servo motor for an extended period of time (guideline: three or
more months).
Always store the servo motor indoors in a clean and dry place.
If it is stored in a dusty or damp place, make adequate provision, e.g. cover the whole product.
If the insulation resistance of the winding decreases, reexamine the storage method.
Though the servo motor is rust-proofed before shipment using paint or rust prevention oil, rust may be
produced depending on the storage conditions or storage period.
If the servo motor is to be stored for longer than six months, apply rust prevention oil again especially to
the machined surfaces of the shaft, etc.
Before using the product after storage for an extended period of time, hand-turn the motor output shaft to
confirm that nothing is wrong with the servo motor. (When the servo motor is equipped with a brake,
make the above check after releasing the brake with the brake power supply.)
When the equipment has been stored for an extended period of time, consult Mitsubishi.
(7) Maintenance, inspection and parts replacement
With age, the electrolytic capacitor of the servo amplifier will deteriorate. To prevent a secondary accident
due to a fault, it is recommended to replace the electrolytic capacitor every 10 years when used in general
Please consult our sales representative.
(8) General instruction
To illustrate details, the equipment in the diagrams of this Instruction Manual may have been drawn
without covers and safety guards. When the equipment is operated, the covers and safety guards must be
installed as specified. Operation must be performed in accordance with this Instruction Manual.
A- 6
Datasheet pdf -


구       성총 70 페이지
다운로드[ MR-E-70A-KH003.PDF 데이터시트 ]

구매 문의
일반 IC 문의 : 샘플 및 소량 구매

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

상호 : 아이지 인터내셔날

사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ]


관련 데이터시트

부품번호상세설명 및 기능제조사

General-Purpose AC Servo

MITSUBISHI    |   2020   |  연락처   |  링크모음   |   검색  |   사이트맵