|
|
|
부품번호 | DJ-175 기능 |
|
|
기능 | Service Manual | ||
제조업체 | ALINCO | ||
로고 | |||
전체 28 페이지수
Service Manual
DJ-175
Specifications
Circuit Description
Parts List
Exploded View
PC Board View
Adjustment
Schematic Diagram
Block Diagram
http://www.DataSheet4U.net/
ALINCO, INC.
datasheet pdf - http://www.DataSheet4U.net/
4. Audio Circuit
The audio signal from pin 9 of IC103 is amplified by the AF amplifier (Q120).
The signal is then input to pin 16 of the electronic volume (IC105) for volume
adjustment, and output from pin 14. The adjusted signal is sent to the audio
power amplifier (IC104) through pin 2 to drive the speaker.
5. Squelch Circuit
The signal except for the noise component in AF signal of IC103 is cut by the
active filter inside IC. The noise component is amplified and rectified, then
converted to the DC voltage to output from pin 14 of IC103. The voltage is led
to pin 2 of CPU and compared with the setting voltage. The squelch will open if
the input voltage is lower than the setting voltage.
2) Transmitter System
1. Modulator Circuit
The audio signal is converted to an electric signal in either the internal or
external microphone, and input to the microphone amplifier (IC110). IC110
consists of two operational amplifiers; one amplifier (pins 12, 13, and 14) is
composed of pre-emphasis and IDC circuits and the other (pins 5, 6, 7, 8, 9,
and 10) is composed of a splatter filter. The maximum frequency deviation is
obtained by IC105 and input to the cathode of the varicap of the VCO, to
change the electric capacity in thehttp://www.DataSheet4U.net/ oscillation circuit. This produces the
frequency modulation.
2. Power Amplifier Circuit
The transmitted signal is oscillated by the VCO, amplified by the pre-drive
amplifier (Q101) and drive amplifier (Q106), and input to the final amplifier
(Q105). The signal is then amplified by the final amplifier (Q105) and led to the
antenna switch (D101) and low-pass filter (L104, L102, L101, C119, C118,
C117, C127, C126, C125, C124, C108, and C101), where un-wanted high
harmonic waves are reduced as needed, and the resulting signal is supplied to
the antenna.
3. APC Circuit
Part of the transmission power from the low-pass filter is detected by D108,
converted to DC, and then amplified by a amplifier (IC101). The output voltage
controls the bias voltage from the source of Q105 and Q106 to maintain the
transmission power constant.
datasheet pdf - http://www.DataSheet4U.net/
4페이지 8. CTCSS, DCS Decoder
The voice band of the AF output signal from pin 9 of IC103 is cut by sharp
active filter IC111 and amplified, then led to pin 80 of CPU. The input signal is
compared with the programmed tone frequency code in the CPU. The squelch
will open when they match.
9. Clock Shift
In the unlikely event that CPU clock noise is present on a particular operating
frequency programmed into the radio, you can shift the CPU clock frequency
to avoid the CPU clock-noise. The output signal from pin 8 of the CPU turns
on Q127. Then the oscillation frequency of X104 will be shifted about 200
ppm.
http://www.DataSheet4U.net/
datasheet pdf - http://www.DataSheet4U.net/
7페이지 | |||
구 성 | 총 28 페이지수 | ||
다운로드 | [ DJ-175.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
DJ-175 | Service Manual | ALINCO |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |