UM10562 PDF 데이터시트 : 부품 기능 및 핀배열

부품번호 UM10562
기능 LPC408x/407x User manual
제조업체 NXP Semiconductors
로고 NXP Semiconductors 로고 

전체 30 페이지


No Preview Available !

UM10562 데이터시트, 핀배열, 회로
LPC408x/407x User manual
Rev. 1 — 13 September 2012
User manual
Document information
Info Content
LPC4088FBD208, LPC4088FET208, LPC4088FET180,
LPC4088FBD144, LPC4078FBD208, LPC4078FET208,
LPC4078FBD144, LPC4078FBD80, LPC4076FET180, LPC4074FBD144,
LPC4074FBD80, ARM, ARM Cortex-M4, 32-bit, USB, Ethernet, LCD,
CAN, I2C, I2S, Flash, EEPROM, Microcontroller
LPC408x/407x user manual
datasheet pdf -

UM10562 pdf, 반도체, 판매, 대치품
NXP Semiconductors
Chapter 1: Introductory information
1.2 Features
Refer to Section 1.4 for details of features for specific part numbers.
Functional replacement for LPC23xx and 24xx family devices.
ARM Cortex-M4 processor, running at frequencies of up to 120 MHz. The Cortex-M4
executes the Thumb®-2 instruction set for optimal performance and code size,
including hardware division, single cycle multiply, and bit-field manipulation. A
Memory Protection Unit (MPU) supporting eight regions is included.
Cortex-M4 built-in Nested Vectored Interrupt Controller (NVIC).
Cortex-M4 Floating Point Unit (FPU), supporting single-precision floating-point
computation functionality in compliance with the ANSI/IEEE Standard 754-2008. The
FPU provides add, subtract, multiply, divide, multiply and accumulate, and square root
operations. It also performs a variety of conversions between fixed-point,
floating-point, and integer data formats. The FPU is not available on LPC4074
Up to 512 kB on-chip flash program memory with In-System Programming (ISP) and
In-Application Programming (IAP) capabilities. The combination of an enhanced flash
memory accelerator and location of the flash memory on the CPU local code/data bus
provides high code performance from flash.
Up to 96 kB on-chip SRAM includes:
Up to 64 kB of Main SRAM on the CPU code/data bus for high-performance CPU
Up to two 16 kB SRAM blocks with separate access paths for higher throughput.
These SRAM blocks may be used for Ethernet, USB, LCD, and DMA memory, as
well as for general purpose instruction and data storage.
Up to 4,032 bytes of on-chip EEPROM.
External Memory Controller provides support for asynchronous static memory devices
such as RAM, ROM and Flash up to 64 MB, as well as dynamic memories such as
Single Data Rate SDRAM.
Eight channel General Purpose DMA controller (GPDMA) on the AHB multilayer
matrix that can be used with the SSP, I2S, UART, SD/MMC, CRC engine,
Analog-to-Digital and Digital-to-Analog converter peripherals, timer match signals,
GPIO, and for memory-to-memory transfers.
Multilayer AHB matrix interconnect provides a separate bus for each AHB master.
AHB masters include the CPU, General Purpose DMA controller, Ethernet MAC, LCD
controller, and the USB interface. This interconnect provides communication with no
arbitration delays unless two masters attempt to access the same slave at the same
Split APB bus allows for higher throughput with fewer stalls between the CPU and
DMA. A single level of write buffering allows the CPU to continue without waiting for
completion of APB writes if the APB was not already busy.
LCD controller, supporting both Super-Twisted Nematic (STN) and Thin-Film
Transistor (TFT) displays. The LCD controller is not available on LPC407x devices.
Dedicated DMA controller.
Selectable display resolution (up to 1024 × 768 pixels).
User manual
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 13 September 2012
© NXP B.V. 2012. All rights reserved.
4 of 942
datasheet pdf -


UM10562 전자부품, 판매, 대치품
NXP Semiconductors
Chapter 1: Introductory information
12 MHz Internal RC oscillator (IRC) trimmed to 1% accuracy that can optionally be
used as a system clock.
An on-chip PLL allows CPU operation up to the maximum CPU rate without the need
for a high-frequency crystal. May be run from the main oscillator or the internal RC
A second, dedicated PLL may be used for the USB and/or SPIFI interfaces in order to
allow added flexibility for the Main PLL settings.
Versatile pin function selection feature allows many possibilities for using on-chip
peripheral functions.
Boundary scan for simplified board testing.
Unique device serial number for identification purposes.
Available as 208-pin LQFP, 208-pin TFBGA, 180-pin TFBGA, 144-pin LQFP, 80-pin
LQFP packages.
1.3 Applications
Point-of-sale terminals, Web servers, multi-protocol bridges
Automation controllers, application control, robotic controls, HVAC, PLC, inverters,
circuit breakers, medical scanning, security monitoring, motor drive, video intercom
Audio, MP3 decoders, alarm systems, displays, printers, scanners, small
appliances, fitness equipment
Aftermarket, car alarms, GPS/Fleet Monitor
User manual
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 13 September 2012
© NXP B.V. 2012. All rights reserved.
7 of 942
datasheet pdf -


구       성총 30 페이지
다운로드[ UM10562.PDF 데이터시트 ]
구매 문의
일반 IC 문의 : 샘플 및 소량 구매

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

휴대전화 : 010-3582-2743

상호 : 아이지 인터내셔날

전화번호 : 051-319-2877, [ 홈페이지 ]


링크 :

관련 데이터시트

부품번호상세설명 및 기능제조사

LPC408x/407x User manual

NXP Semiconductors
NXP Semiconductors    |   2019   |  연락처   |  링크모음   |   검색  |   사이트맵