|
|
PDF PL320QMT Data sheet ( Hoja de datos )
| Número de pieza | PL320QMT | |
| Descripción | Laboratory Power Supplies | |
| Fabricantes | TTI | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de PL320QMT (archivo pdf) en la parte inferior de esta página. Total 2 Páginas | ||
|
No Preview Available !
Technical Specifications
MODEL SELECTOR GUIDE
MODEL
MAIN OUT PUT(S)
LOGIC
OUTPUT
INTERFACES
GPIB ARC
PL310
0 - 32V at 0 - 1A
PL320
0 - 32V at 0 - 2A
PL154
0 - 15.5V at 0 - 4A
PL330
0 - 32V at 0 - 3A
PL310QMD 2 x 0 - 32V at 0 - 1A
or 0 - 32V at 0 - 2A
or 0 - 64V at 0 - 1A
or 0 - ±32V at 0 - 1A
PL320QMD 2 x 0 - 32V at 0 - 2A
or 0 - 32V at 0 - 4A
or 0 - 64V at 0 - 2A
or 0 - ±32V at 0 - 2A
PL330QMD 2 x 0 - 32V at 0 - 3A
or 0 - 32V at 0 - 6A
or 0 - 64V at 0 - 3A
or 0 - ±32V at 0 - 3A
PL310QMT 2 x 0 - 32V at 0 - 1A 5V at 1.5A
or 0 - 32V at 0 - 2A
or 0 - 64V at 0 - 1A
or 0 - ±32V at 0 - 1A
PL320QMT 2 x 0 - 32V at 0 - 2A
or 0 - 32V at 0 - 4A
4 - 6V at
0.1 - 4A
or 0 - 64V at 0 - 2A
or 0 - ±32V at 0 - 2A
PL330QMT 2 x 0 - 32V at 0 - 3A
or 0 - 32V at 0 - 6A
4 - 6V at
0.1 - 7A
or 0 - 64V at 0 - 3A
or 0 - ±32V at 0 - 3A
PL330P
0 - 32V at 0 - 3A
Yes Yes
PL330DP 2 x 0 - 32V at 0 - 3A
Yes Yes
PL330TP 2 x 0 - 32V at 0 - 3A 4 - 6V at 1 - 7A Yes Yes
Mod els il lus trated within this bro chure:-
Front cover - PL330, PL320QMD, PL310QMT
In side pages - PL330QMT, PL330DP
MAIN OUTPUT(S)
Out put Range:
0 - 32 Volts nomi nal; 0 - 15.5V (PL154).
0 - 1.1A nomi nal (PL310);
0 - 2.1A nomi nal (PL320);
0 - 3.1A nomi nal (PL330);
0 - 4A nomi nal (PL154).
Out put Volt age
Setting:
By coarse and fine con trols; reso lu tion bet ter than 5mV
across the range.
Out put Cur rent
Setting:
By sin gle loga rith mic con trol.
Out put Mode:
The power sup ply op er ates in con stant cur rent or con stant
volt age modes with auto mat ic cross- over. Deci mal points
flash to in di cate con stant cur rent mode.
Configuration
Iso lated, True par al lel, Se ries or Se ries Track ing via front
Selection:
panel switches.
(QMD and QMT only)
Out put Switch:
Iso lates the out put and per mits volt age and cur rent lim its to
be set up bef ore con nect ing the load.
OutputTerminals: 4mm ter mi nals on 19mm (0.75") spac ing.
OutputImpedance: ConstantVoltage:Typically<5m Ω at 1kHz
Con stant Cur rent: Typi cally 50kΩwith volt age limit at maxi-
mum
OutputProtection: Uptomaximumoutputvoltage+20Voltsforward;diode
clamped for re verse volt ages and up to 3A re verse cur rent.
LoadRegulation: <0.01% of maxi mum out put for 90% load change
LineRegulation: <0.01% of maxi mum out put for 10% line volt age change
Re mote Sense:
Elimi nates up to 0.5V drop per lead.
Rip ple and Noise: Typi cally <1mV rms
TransientResponse: <20usec to within 50mV of set ting for 90% load change
Tem pera ture
Coefficient:
Typi cally <100ppm/oC
Me ter Type:
Dual 3.75 digit (4095 count) with 12.5mm (0.5") LEDS,
(scale length in creased to 8190 on PL330QMD/QMT).
Read ing rate 4 per sec ond.
MeterResolution: Volt age: 10mV over the en tire range
Cur rent: 1mA over the en tire range
MeterAccuracy: Voltage: ±(0.1% of read ing + 1 digit)
Cur rent Me ter
Cur rent: ±(0.3% of read ing + 1 digit)
Nomi nally 20ms switchable to 2 sec for av er ag ing of rap idly
Damping:
vary ing loads
LOGIC OUTPUT - PL310QMT
Out put Volt age:
Fixed 5 V± 0⋅1 V.
Max.OutputCurrent: >1⋅5 Amps.
OutputTerminal: 4mm ter mi nals on 19mm (0⋅75") spac ing.
OutputProtection: Out put will with stand up to 16 V for ward volt age. Di ode
clamped for re verse volt ages and up to 3 Amps re verse cur-
rent.
LoadRegulation: < 0⋅3% for 50% load change.
LineRegulation: < 0⋅1% for 10% line change.
LOGIC OUTPUT - PL320QMT
Out put Volt age
Range:
4 to 6 Volts
Out put Cur rent:
0.1 to 4 Amps.
Out put Switch:
Iso lates the out put and per mits out put volt age to be set bef-
ore con nect ing the load.
OutputTerminals: 4mm ter mi nals on 19mm (0.75") spac ing.
Over-Voltage
Pro tec tion:
Above 7 Volts
Out put Pro tec tion:
LoadRegulation:
Clamped by the over- voltage pro tec tion cir cuit for for ward
volt ages over 7 Volts and up to 1 Amp for ward cur rent. Di ode
clamped for re verse volt ages and up to 3 Amps re verse cur -
rent.
<0.01% of maxi mum out put for 90% load change
LineRegulation: <0.01% of maxi mum out put for 10% line volt age change
Re mote Sense:
Elimi nates up to 0.5V drop per lead.
Rip ple and Noise: Typi cally <1mV rms
TransientResponse: <20usec to within 50mV of set ting for 90% load change
Tem pera ture
Coefficient:
Typi cally <100ppm/oC
VoltageSetting
Accuracy:
± 0.1V
Technical Specifications continued
LOGIC OUTPUT - PL330QMT & PL330TP
Out put Volt age
Range:
4 to 6 Volts
Out put Cur rent:
0.1 to 7 Amps.
Out put Switch:
OutputTerminals:
Iso lates the out put and per mits out put volt age to be set bef-
ore con nect ing the load.
4mm ter mi nals on 19mm (0.75") spac ing.
Over- Voltage
Protection:
Above 7 Volts
OutputProtection:
Load Regu la tion:
Clamped by the over- voltage pro tec tion cir cuit for for ward
volt ages over 7 Volts and up to 1 Amp for ward cur rent. D-i
ode clamped for re verse volt ages and up to 3 Amps re verse
current.
<0.01% of maxi mum out put for 90% load change
LineRegulation: <0.01% of maxi mum out put for 10% line volt age change
Re mote Sense:
Elimi nates up to 0.5V drop per lead.
Rip ple and Noise: Typi cally <1mV rms
TransientResponse: <20usec to within 50mV of set ting for 90% load change
Temperature
Coefficient:
Me ter Type:
Typi cally <100ppmo/ C
3.75 digit (4095 count) with 12.5mm (0.5") LEDs. Read ing
rate 4 per sec ond.
MeterResolution: Volt age: 10mV
Cur rent: 10mA
Me ter Ac cu racy:
Voltage: ±(0.2% of read ing + 1 digit )
Cur rent:±(0.5% of read ing + 1 digit )
PL-P MODELS, ADDITIONAL SPECIFICATIONS
Re mote pro gram ma ble ver sions in the range fea ture full con trol, read back and
status re port ing via the GPIB and RS232 in ter faces. The GPIB in ter face con-
forms to the IEEE 488.1 and 488.2 stan dards and the RS232 in ter face is fully
com pati ble with the Thurlby- Thandar Ad dress able RS232 Chain (ARC) stan dard.
8 rear panel DIP switches are used to spec ify baud rate, bus ad dress and ac tive
in ter face (GPIB or RS232). Re mote/Lo cal op era tion is se lected by a front panel
switch.
LOCALOPERATION
For a pro gram ma ble in stru ment op er ated in lo cal state, all ca pa bili ties and speci-
fi ca tions re main un changed from those of a stan dard in stru ment .
REMOTEOPERATION
With the in stru ment switched to the re mote state, all volt age and cur rent ad just-
ment con trols be come in op era tive and com mands re ceived over the ac tive in ter-
face will be parsed and exe cuted.
MAIN OUTPUT(S) - REMOTE OPERATION
Out put Volt age
Setting:
12 bit reso lu tion (10mV steps)
Out put Cur rent
Setting:
12 bit reso lu tion (1mA steps)
SettingAccuracy: Voltage: ±(0.1% + 10mV)
Current: ±(0.2% + 2mA)
Out put Switch:
Elec tronic by in ter face com mand (front panel out put
switches must be set to ON)
Readback Resolution:Volt age: 10mV over the en tire range
Cur rent: 1mA over the en tire range
Readback Accuracy:Volt age: ±(0.1% of read ing + 1 digit)
Cur rent:±(0.3% of read ing + 1 digit)
CurrentMeter
Damping:
Nomi nally 20ms switchable to 2 sec and back by re mote
commands
LOGIC OUTPUT (PL330TP) - REMOTE OPERATION
Out put Volt age
Range:
4 to 6 Volts in 10mV steps
OutputCurrent: 1 to 7 Amps in ap proxi mate 1A steps
SettingAccuracy: Voltage: ±(0.2% + 10mV)
Out put Switch:
Elec tronic by in ter face com mand (front panel out put switch
must be set to ON)
ReadbackResolution:Current:10mA
ReadbackAccuracy: Cur rent:±(0.5% of read ing + 1 digit )
REMOTE CONTROL INTERFACES - PL-P MODELS
Both in ter faces fea ture full con trol, read back and status re port ing.
RS232:
Vari able Baud rate (9600 maxi mum), 9 pin D- connector (fe-
male). Fully com pati ble with ARC (Ad dress able RS232
Chain) sys tem.
GPIB:
Con form ing with IEEE- 488.1 and IEEE- 488.2
AddressSelection: By rear panel DIP switch.
Remote/Local
Operation:
Se lected by front panel switch.
Re mote Com mand Re sponse Time:
Interface:
<15 ms (sin gle com mand, in put buffer empty).
Out put Volt age - UpT: ime con stant typi cally 2ms, e.g. 10ms to set tle within 1%
of a step change, 15ms to set tle within 0.1%.
OutputVoltage-DowTni:me con stant de ter mined by the dis charge of the power
sup ply out put ca paci tor (47uF). Typi cally <10ms to set tle
within 1% for a 10V step change at 50mA load cur rent; typi -
cally <200ms to set tle within 1% at zero load.
OutputCurrent: Typi cally 50ms to set tle within 10mA for a 1A change.
GENERAL
PowerRequirements:
InputVoltage:
In ter nally set for 110, 120, 220 or 240VAC 50/60Hz
In put Volt age Range: ±10% of volt age set ting
Power Con sump tion:
Single Dual Triple
30V/1A
75VA 150VA 300VA
15V/4A & 30V/2A150VA 300VA 450VA
30V/3A
225VA 450VA 600VA
Environmental:
OperatingRange:5oC to 40oC, 20% to 80% RH
StorageRange:-20 oC to +60oC
Weight:
Single Dual Triple
30V/1A PL
4.0kg 8.0kg 11.5kg
15V/4A PL
5.0kg
30V/2A PL
5.0kg 9.5kg 13.5kg
30V/3A PL
6.0kg 12.0kg 15.5kg
30V/3A PL-P 6.5kg 12.5kg 16.0kg
Size:
PL310, PL154, &
PL320:
155mm(W) x 170mm(H) x 265mm(D)
PL330:
155mm(W) x 170mm(H) x 300mm(D)
PL330P:
htp:/www.DataSheet4U.net/
207mm(W) x 170mm(H) x 300mm(D)
PL310QMD, PL310QMT, &
PL320QMD:
350mm(W) x 170mm(H) x 265mm(D)
PL330QMD, &
PL330DP:
350mm(W) x 170mm(H) x 300mm(D)
PL320QMT:
425mm(W) x 170mm(H) x 265mm(D)
PL330QMT, &
PL330TP:
425mm(W) x 170mm(H) x 300mm(D)
Rack Mount Op tion: 19 inch 4U mount for two PL330P or one PL330DP/TP.
Anti- tamper cover for se cu rity.
ElectricalSafety: De signed and manu fac tured to com ply with IEC 348 and
IEC1010-1. Full safety sock ets avail able to spe cial or der.
EMC:
De signed and manu fac tured to com ply with EN50081–1
and EN50082–1.
Thurlby Than dar In stru ments Ltd. op er ates a pol icy of con tinu ous de vel op ment and
re serves the right to al ter speci fi ca tions with out prior no tice.
De signed and built in the U.K. by:
Thurlby Than dar In stru ments Ltd .
Glebe Road, Hun ting don. Cambs. PE18 7DX Eng land
Tel: 01480 412451 Fax: 01480 450409 e- mail: [email protected]
82100-0046
THURLBY THANDAR INSTRUMENTS
PL & PL-P Series
Laboratory Power Supplies
Standard and Programmable models, 35 watts to 240 watt
datashepeh-dtpf:/www.DataSheet4U.net/
1 page | ||
| Páginas | Total 2 Páginas | |
| PDF Descargar | [ Datasheet PL320QMT.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PL320QMT | Laboratory Power Supplies | TTI |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |