MKP2C031501H00xxxx Datasheet PDF - WIMA
| Part Number | MKP2C031501H00xxxx | |
| Description | Metallized Polypropylene Capacitors | |
| Manufacturers | WIMA | |
| Logo |  |
|
|
There is a preview and MKP2C031501H00xxxx download ( pdf file ) link at the bottom of this page. Total 8 Pages | ||
Preview 1 page No Preview Available !
WIMA MKP 2
Metallized Polypropylene (PP)
Capacitors in PCM 5 mm
D
Special Features
˜ High volume/capacitance ratio
˜ Self-healing
˜ Increased pulse duty from
250 VDC rated voltage
˜ Very low dissipation factor
˜ Negative capacitance change
versus temperature
˜ Very low dielectric absorption
˜ According to RoHS 2002/95/EC
Typical Applications
For high frequency applications e.g.
˜ Sample and hold
˜ Timing
˜ Oscillating circuits
˜ High frequency coupling and
decoupling
Construction
Dielectric:
Polypropylene (PP) film
Capacitor electrodes:
Vacuum-deposited
Internal construction:
Plastic film
Vacuum-deposited
electrode
Metal contact layer
(schoopage)
Terminating wire
Encapsulation:
Solvent-resistant, flame-retardant plastic
case with epoxy resin seal, UL 94 V-0
Terminations:
Tinned wire.
Marking:
Colour: Red. Marking: Black.
Epoxy resin seal: Red
Electrical Data
Capacitance range:
1000 pF to 0.33 mF (E12-values on request)
Rated voltages:
63 VDC, 100 VDC, 250 VDC, 400 VDC,
630 VDC, 1000 VDC
Capacitance tolerances:
± 20%, ±10%, ±5%
Operating temperature range:
–55+ C to +100+ C
Test specifications:
In accordance with IEC 60384-16
and EN 131 200
Climatic test category:
55/085/56 in accordance with IEC
Insulation resistance at +20+ C:
3 x 104 M¸
(mean value: 1 x 105 M¸)
Measuring voltage:
Ur = 63 V: Utest = 50 V/1 min.
Ur 100 V: Utest = 100 V/1 min.
Test voltage:
1.6 Ur, 2 sec.
Maximum pulse rise time:
Dielectric absorption:
0.05 %
Dissipation factors at +20+ C: tan d
at f C0.1 mF 0.1 mF P C 0.33 mF
1 kHz 0.5 x 10-3
10 kHz 0.8 x 10-3
100 kHz 3.0 x 10-3
0.5 x 10-3
0.8 x 10-3
–
Voltage derating:
A voltage derating factor of 1.35 % per K
must be applied from +85+ C for DC
voltages and from +75+ C for AC
voltages
Reliability:
Operational life 300 000 hours
Failure rate 2 fit (0.5 x Ur and 40+ C)
Ca ppaFc/imtaF nce
http://www.DataSheet4U.net/
63 VDC
max. pulse rise time V/msec
100 VDC 250 VDC 400 VDC 630 VDC 1000 VDC
1000 ... 2200
3300 ... 6800
0.01 ... 0.022
0.033 ... 0.068
0.1 ... 0.22
0.33
–
–
100
100
100
100
– –
– –
100 250
100 250
100 250
100 250
300 400
300 400
300 400
300 400
– –
– –
500
500
500
–
–
–
for pulses equal to the rated voltage
Mechanical Tests
Packing
Pull test on pins:
10 N in direction of pins according to
IEC 60068-2-21
Vibration:
6 hours at 10 ... 2000 Hz and 0.75 mm
displacement amplitude or 10 g in
accordance with IEC 60068-2-6
Low air density:
1kPa = 10 mbar in accordance with
IEC 60068-2-13
Bump test:
4000 bumps at 390 m/sec2 in
accordance with IEC 60068-2-29
Available taped and reeled.
Detailed taping information and graphs
at the end of the catalogue.
For further details and graphs please
refer to Technical Information.
36
This datasheet has been downloaded from http://www.digchip.com at this page
|
| |
 
Typical Dimensions for
Taping Configuration
P2 P
P1
D0
Fd
P0
P
Vh
Diagram 1:
PCM 2.5/5/7.5mm
P
P1 P1
D
dd
F P0
P2
P2
F
P0
Diagram 2: PCM 10/15 mm
Diagram 3: PCM 22.5 and 27.5*mm
*PCM 27.5 taping possible with two feed holes between components
Designation
Symbol PCM 2.5 taping
PCM 5 taping
Dimensions for Radial Tapinghttp://www.DataSheet4U.net/
PCM 7.5 taping
PCM 10 taping*
PCM 15 taping*
PCM 22.5 taping PCM 27.5 taping
Carrier tape width
W 18.0 p0.5
18.0 p0.5
18.0 p0.5
18.0 p0.5
18.0 p0.5
18.0 p0.5
18.0 p0.5
Hold -dow n tape widt h W 0 6.0 faodrhheosti-vseeatalipneg 6 .0 faodrhheosti-vseeatalipneg 1 2 .0 faodrhheosti-vseeatalipneg 1 2 .0 faodrhheosti-vseeatalipneg 1 2 .0 faodrhheosti-vseeatalipneg 1 2 .0 faodrhheosti-vseeatalipneg 1 2 .0 faodrhheosti-vseeatalipneg
Hole position
W1
Hold-down tape position W2
Feed hole diameter
D0
Pitch of component
P
Feed hole pitch P0
9.0 p0.5
9.0 p0.5
9.0 p0.5
9.0 p0.5
9.0 p0.5
9.0 p0.5
9.0 p0.5
0.5 to 3.0 max.
0.5 to 3.0 max.
0.5 to 3.0 max.
0.5 to 3.0 max.
0.5 to 3.0 max.
0.5 to 3.0 max.
0.5 to 3.0 max.
4.0 p0.2
12.7 p1.0
4.0 p0.2
12.7 p1.0
4.0 p0.2
12.7 p1.0
4.0 p0.2
25.4 p1.0
4.0 p0.2
25.4 p1.0
4.0 p0.2
38.1 p1.5
4.0 p0.2
3*8.1 p1.5 or 50.8 p1.5
12.7 p0.3
cumulative pitch
error max.
12.7 p0.3
cumulative pitch
error max.
12.7 p0.3
cumulative pitch
error max.
12.7 p0.3
cumulative pitch
error max.
12.7 p0.3
cumulative pitch
error max.
12.7 p0.3
cumulative pitch
error max.
12.7 p0.3
cumulative pitch
error max.
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
Feed hole centre
to pin
P1 5.1 p0.5
3.85 p0.7
2.6 p0.7
7.7 p0.7
5.2 p0.7
7.8 p0.7
5.3 p0.7
Hole centre to
component centre
P2 6.35 p1.3
6.35 p1.3
6.35 p1.3
12.7 p1.3
12.7 p1.3
19.05 p1.3
19.05 p1.3
Feed
edge
hooflethececnotrmeptoonbeonttt om H
Feed
edge
hoof lethececnotrmeptoonteonpt H1
16.5 p0.3
18.5 p0.5
H+Hcomponent < H1
32.25 max.
16.5 p0.3
18.5 p0.5
H+Hcomponent < H1
32.25 max.
16.5 p0.5
18.5 p0.5
H+Hcomponent < H1
24.5 to 31.5
16.5 p0.5
18.5 p0.5
H+Hcomponent < H1
25.0 to 31.5
16.5 p0.5
18.5 p0.5
H+Hcomponent < H1
26.0 to 37.0
16.5 p0.5
18.5 p0.5
H+Hcomponent < H1
30.0 to 43.0
16.5 p0.5
18.5 p0.5
H+Hcomponent < H1
35.0 to 45.0
Pin spacing
upper edge
at
of
carrier
tape F 2 .5 p0.5 5.0
+–00..28
Pin diameter
d 0.4 p0.05
0.5 p0.05
Component alignment
Dh p 2.0 max.
p 2.0 max.
7.5 p0.8
„ 0.5 p0.05 or 0.6 +–00..0065
p 3.0 max.
10.0 p0.8
„ 0.5 p0.05 or 0.6 +–00,.0065
p 3.0 max.
15 p0.8
0.8 +–00,.0085
p 3.0 max.
22.5 p0.8
0.8 +–00,.0085
p 3.0 max.
27.5 p0.8
0.8
+0.08
–0.05
p 3.0 max.
Total tape thickness
t 0.7 p0.2
0.7 p0.2
0.7 p0.2
0.7 p0.2
0.7 p0.2
0.7 p0.2
0.7 p0.2
ROLL/AMMO
P(saecekaaglseo page 128)
REEL
P
P
33600pm1a x. B
52
58
p2
p2
depending on
comp. dimensions
Unit
AMMO
REE L PP 33 600pm1a x. B
52
58
66
ppp222 or REEL PP 52050p m1a x. B
54
60
68
p2
p2
p2
see details page 130.
depending
on PCM and
component dimensions
Dims in mm.
„ Diameter of pins see General Data.
* PCM 10 and PCM 15 can be crimped to PCM 7.5.
Position of components according to PCM 7.5 (sketch 1). P0 = 12.7 or 15.0 is possible
Please clarify customer-specific deviations with the manufacturer.
127
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MKP2C031501H00xxxx electronic component. |
| Information | Total 8 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ MKP2C031501H00xxxx.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| MKP2C031501H00xxxx | The function is Metallized Polypropylene Capacitors. WIMA | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
MKP2
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||