|
|
|
부품번호 | ETK6201 기능 |
|
|
기능 | LED Controller/Driver | ||
제조업체 | Etek Microelectronics | ||
로고 | |||
Etek
Microelectronics
ETK6201
LED Controller/Driver
DESCRIPTION
ETK6201 is an LED Controller driven on a 1/7 to 1/8 duty factor. 11 segment output lines, 6 grid output lines,
1 segment/grid output lines, one display memory, control circuit, key scan circuit are all incorporated into a single
chip to build a highly reliable peripheral device for a single chip microcomputer. Serial data is fed to ETK6201 via
a four-line serial interface. Housed in a 32-pin SOP Package, ETK6201 pin assignments and application circuit are
optimized for easy PCB Layout and cost saving advantages.
FEATURES
z CMOS Technology
z Low Power Consumption
z Multiple Display Modes(12 segment, 6 Grid to 11 segment, 7 Grid)
z Key Scanning (10×3 Matrix)
z 8-step Dimming Circuitry
z Serial Interface for Clock, Data Input, Data Output, Strobe Pins and low voltage operation ability when user’s
MCU power supply is 3.3V
z Available in 32-pin, SOP Package
PIN CONFIGURATION
OSC
DOUT
DIN
CLK
STB
K1
K2
K3
VDD
SG1/KS1
SG2/KS2
SG3/KS3
NC
SG4/KS4
SG5/KS5
SG6/KS6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32 GND
31 GR1
30 GR2
29 GND
28 GR3
27 GR4
26 GND
ETK6201 25 VDD
24 SG14/GR5
23 SG13/GR6
22 SG12/GR7
21 SG11
20 SG10/KS10
19 SG9/KS9
18 SG8/KS8
17 SG7/KS7
1/16
Rev 2.1 2009-4-28
Free Datasheet http://www.datasheet4u.com/
4. Output Pins:SG1 to SG11
ETK6201
VDD
5. Output Pins:SG14/GR5, SG13/GR6 and SG12/GR7
GND
VDD
GND
Rev 2.1 2009-4-28
4/16
4페이지 ETK6201
Each data entered by each key is stored as follows and read by a READ Command, starting from the last
significant bit of the next data(b7) is read.
K1………………K3
SG1/KS1
SG3/KS3
SG5/KS5
SG7/KS7
SG9/KS9
K1………………K3
SG2/KS2
SG4/KS4
SG6/KS6
SG8/KS8
SG10/KS10
x
x
x
x
x
READING
SEQUENCE
b0…………….b2
b3………………b5
b6………………b7
Note: b6~b7 do not care.
Command 3:Address Setting Commands
Address Setting Commands are used to set the address of the display memory. The address is considered
valid if it has a value of 00H to 0DH. If the address is set to 0EH or higher, the data is ignored until a valid
address is set. When power is turned ON, the address is set at 00H.
MSB
LSB
1 1 ─ ─ b3 b2 b1 b0
b4, b5: Not Relevant
The address of b3~b0: 00H~0DH
DISPLAY MODE AND RAM ADDRESS
Data transmitted from an external device to ETK6201 via the interface are stored in the Display RAM and
are assigned address.
The RAM addresses of ETK6201 are given below in 8 bits unit.
SG1…………SG4 SG5…………SG8 SG9…………SG12
00HL
02HL
04HL
06HL
08HL
0AHL
0CHL
00HU
02HU
04HU
06HU
08HU
0AHU
0CHU
01HL
03HL
05HL
07HL
09HL
0BHL
0DHL
SG13…………SG14
01HU
03HU
05HU
07HU
09HU
0BHU
0DHU
DIG1
DIG2
DIG3
DIG4
DIG5
DIG6
DIG7
b0…………….b3
xxHL
Lower 4 bits
b4………………b7
xxHU
Higher 4 bits
Command 4:Display Control Commands
The Display Control Commands are used to turn ON or OFF a display. It also used to set the pulse width.
Please refer to the diagram below. When the power is turned ON, a 1/16 pulse width is selected and the displayed
is turned OFF (the key scanning is stopped).
MSB
10
b4, b5: Not Relevant
Display Setting:
LSB
─ ─ b3 b2 b1 b0
Rev 2.1 2009-4-28
7/16
7페이지 | |||
구 성 | 총 16 페이지수 | ||
다운로드 | [ ETK6201.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
ETK6201 | LED Controller/Driver | Etek Microelectronics |
ETK6203 | LED Controller/Driver | ETEK |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |