Datasheet.kr   

AT90USB1286 데이터시트 PDF




ATMEL Corporation에서 제조한 전자 부품 AT90USB1286은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 AT90USB1286 자료 제공

부품번호 AT90USB1286 기능
기능 (AT90USBxxx) 8-bit Microcontroller
제조업체 ATMEL Corporation
로고 ATMEL Corporation 로고


AT90USB1286 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 70 페이지수

미리보기를 사용할 수 없습니다

AT90USB1286 데이터시트, 핀배열, 회로
Features
High Performance, Low Power AVR® 8-Bit Microcontroller
Advanced RISC Architecture
– 135 Powerful Instructions – Most Single Clock Cycle Execution
– 32 x 8 General Purpose Working Registers
– Fully Static Operation
– Up to 16 MIPS Throughput at 16 MHz
– On-Chip 2-cycle Multiplier
Non-volatile Program and Data Memories
– 32/64/128K Bytes of In-System Self-Programmable Flash
• Endurance: 100,000 Write/Erase Cycles
– Optional Boot Code Section with Independent Lock Bits
• USB Bootloader programmed by default in the Factory
• In-System Programming by On-chip Boot Program hardware activated after
reset
• True Read-While-Write Operation
• All supplied parts are preprogramed with a default USB bootloader
– 1K/2K/4K (32K/64K/128K Flash version) Bytes EEPROM
• Endurance: 100,000 Write/Erase Cycles
– 2.5K/4K/8K (32K/64K/128K Flash version) Bytes Internal SRAM
– Up to 64K Bytes Optional External Memory Space
– Programming Lock for Software Security
JTAG (IEEE std. 1149.1 compliant) Interface
– Boundary-scan Capabilities According to the JTAG Standard
– Extensive On-chip Debug Support
– Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface
USB 2.0 Full-speed/Low-speed Device and On-The-Go Module
– Complies fully with:
– Universal Serial Bus Specification REV 2.0
– On-The-Go Supplement to the USB 2.0 Specification Rev 1.0
– Supports data transfer rates up to 12 Mbit/s and 1.5 Mbit/s
USB Full-speed/Low Speed Device Module with Interrupt on Transfer Completion
– Endpoint 0 for Control Transfers : up to 64-bytes
– 6 Programmable Endpoints with IN or Out Directions and with Bulk, Interrupt or
Isochronous Transfers
– Configurable Endpoints size up to 256 bytes in double bank mode
– Fully independant 832 bytes USB DPRAM for endpoint memory allocation
– Suspend/Resume Interrupts
– Power-on Reset and USB Bus Reset
– 48 MHz PLL for Full-speed Bus Operation
– USB Bus Disconnection on Microcontroller Request
USB OTG Reduced Host :
– Supports Host Negotiation Protocol (HNP) and Session Request Protocol (SRP)
for OTG dual-role devices
– Provide Status and control signals for software implementation of HNP and SRP
– Provides programmable times required for HNP and SRP
Peripheral Features
– Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
– Two16-bit Timer/Counter with Separate Prescaler, Compare- and Capture Mode
8-bit
Microcontroller
with
64/128K Bytes
of ISP Flash
and USB
Controller
ATmega32U6
AT90USB646
AT90USB647
AT90USB1286
AT90USB1287
7593H–AVR–11/08
Free Datasheet http://www.datasheet4u.com/




AT90USB1286 pdf, 반도체, 판매, 대치품
Figure 1-2. Pinout ATmega32U6/AT90USB64/128-QFN
(INT.6/AIN.0) PE6 1
(INT.7/AIN.1/UVcon) PE7 2
UVcc 3
D- 4
D+ 5
UGnd 6
UCap 7
VBus 8
(IUID) PE3 9
(SS/PCINT0) PB0 10
(PCINT1/SCLK) PB1 11
(PDI/PCINT2/MOSI) PB2 12
(PDO/PCINT3/MISO) PB3 13
(PCINT4/OC.2A) PB4 14
(PCINT5/OC.1A) PB5 15
(PCINT6/OC.1B) PB6 16
INDEX CORNER
ATmega32U6
AT90USB128/64
(64-lead QFN top view)
48 PA3 (AD3)
47 PA4 (AD4)
46 PA5 (AD5)
45 PA6 (AD6)
44 PA7 (AD7)
43 PE2 (ALE/HWB)
42 PC7 (A15/IC.3/CLKO)
41 PC6 (A14/OC.3A)
40 PC5 (A13/OC.3B)
39 PC4 (A12/OC.3C)
38 PC3 (A11/T.3)
37 PC2 (A10)
36 PC1 (A9)
35 PC0 (A8)
34 PE1 (RD)
33 PE0 (WR)
Note:
The large center pad underneath the MLF packages is made of metal and internally connected to
GND. It should be soldered or glued to the board to ensure good mechanical stability. If the center
pad is left unconnected, the package might loosen from the board.
1.1 Disclaimer
Typical values contained in this datasheet are based on simulations and characterization of
other AVR microcontrollers manufactured on the same process technology. Min and Max values
will be available after the device is characterized.
2. Overview
The ATmega32U6/AT90USB64/128 is a low-power CMOS 8-bit microcontroller based on the
AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the
4 ATmega32U6/AT90USB64/128
7593H–AVR–11/08
Free Datasheet http://www.datasheet4u.com/

4페이지










AT90USB1286 전자부품, 판매, 대치품
ATmega32U6/AT90USB64/128
2.2 Pin Descriptions
2.2.1 VCC
Digital supply voltage.
2.2.2 GND
Ground.
2.2.3 AVCC
Analog supply voltage.
2.2.4
Port A (PA7..PA0)
Port A is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port A output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port A pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port A pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port A also serves the functions of various special features of the
ATmega32U6/AT90USB64/128 as listed on page 79.
2.2.5
Port B (PB7..PB0)
Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port B output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port B pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port B has better driving capabilities than the other ports.
Port B also serves the functions of various special features of the
ATmega32U6/AT90USB64/128 as listed on page 80.
2.2.6
Port C (PC7..PC0)
Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port C output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port C pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port C also serves the functions of special features of the ATmega32U6/AT90USB64/128 as
listed on page 83.
2.2.7
Port D (PD7..PD0)
Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port D output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port D pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port D also serves the functions of various special features of the
ATmega32U6/AT90USB64/128 as listed on page 84.
7593H–AVR–11/08
7
Free Datasheet http://www.datasheet4u.com/

7페이지


구       성 총 70 페이지수
다운로드[ AT90USB1286.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
AT90USB1286

8-bit Microcontroller

ATMEL Corporation
ATMEL Corporation
AT90USB1286

(AT90USBxxx) 8-bit Microcontroller

ATMEL Corporation
ATMEL Corporation

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵