|
|
|
부품번호 | TH01 기능 |
|
|
기능 | Temperature and Humidity Module | ||
제조업체 | HOPERF | ||
로고 | |||
전체 7 페이지수
TH01
Temperature and Humidity Module
2012-7-2
Version: 1.4
¾ .Four Pins interface port
¾ .Wide range Temperature and Relative humidity.
¾ .Ultra low power consumption
¾ . Low cost .
¾ . Small size.
Description
The TH01 module is base on one 8-bit MCU, NTC temperature and humidity sensor to measure the
environment atmosphere temperature and humidity. With two lines interface can be directly red. out the
temperature and humidity value, the application is simple for user to access the real temperature and
humidity reading.
TH01 module is in stop mode after measure the atmosphere and humidity.
Features
Humidity Range: 20% - 99%
.Temperature Measure Range:-50℃- 70℃.
.Module Operations Temperature Range: -40℃- 85℃
. Similar I2C Serial Interface
. Voltage Provide Range: 2.6V~5.0V
Applications
.Consumer Products
.Weather Stations
. Humidifiers
. Temperature controller
. Store
Block Diagram
App1 Temperature -20℃~70℃
、
1 Tel: +86‐755‐86096587
App2 Temperature -50℃~70℃
Fax: +86‐755‐86096602 E‐mail: [email protected]
http://www.hoperf.com
Free Datasheet http://www.datasheet4u.com/
TH01
Temperature and Humidity Module
2012-7-2
Version: 1.4
SCK pin is pull up with internal pull-up resistor.
SYN+CODE(data format)
RF
CODE
0
1
SYN
H/L(US)
488/488±20
488/1952±50
488/6958±50
TH01 with two mode
A or B mode Option
TH01 power on after 1 second start to detect the SCK PIN level
PIN level is high; it will work in B mode. SCK pin level must be set high after set mode, At least
3seonds the user can be read data, When in mode A it should be at least 2 seconds interval between
two reads. In mode B, each time SCK pin level changed, TX cycle will reset and TX after 60s.After
power up and set mode, A mode will directly enter sleep, B mode will enter low power consumption
mode after once TX.
A mode
Communication Step
1. Master output the falling edge signal keep this low level for 500ms to 5 seconds on SCK PIN.
2. Master output one dummy clock which high level pulse width will over 1ms.
3. Master output the clock in its fix rate to get each bit data.
4. When SCK at high, the SDA data is stable. The clock rate is from 5k to 100kbps.
5. Data is 4 bytes, 3 bytes data, and 1 byte CRC checksum.
6. Each byte is the MSB first out.
A mode Timing
Sleep
mode
Dummy high
>1ms
END
SCK
500ms<T<5S
get data
Set_SCK
//Before enter sleep mode
4 Tel: +86‐755‐86096587 Fax: +86‐755‐86096602 E‐mail: [email protected]
http://www.hoperf.com
Free Datasheet http://www.datasheet4u.com/
4페이지 TH01
Temperature and Humidity Module
2012-7-2
Version: 1.4
TH01 Mechanical Dimension .
( Top View )
(Bottom View)
(DIP Type)
( SMD Type )
( Thickness)
Importance Note:
HopeRF will change the datasheet without any user permission, but we will update the newest
datasheet into our web size, so please keep the checking.
http://www.hoperf.com
7 Tel: +86‐755‐86096587 Fax: +86‐755‐86096602 E‐mail: [email protected] http://www.hoperf.com
Free Datasheet http://www.datasheet4u.com/
7페이지 | |||
구 성 | 총 7 페이지수 | ||
다운로드 | [ TH01.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
TH01 | Temperature and Humidity Module | HOPERF |
TH02 | DIGITAL I2C HUMIDITY AND TEMPERATURE SENSOR | HOPERF |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |