|
|
PDF 8510J Data sheet ( Hoja de datos )
| Número de pieza | 8510J | |
| Descripción | TDA8510J | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de 8510J (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
DATA SHEET
TDA8510J
26 W BTL and 2 × 13 W SE power
amplifiers
Preliminary specification
Supersedes data of 1999 Jun 14
File under Integrated Circuits, IC01
1999 Dec 14
Free Datasheet http://www.datasheet4u.com/
1 page  
Philips Semiconductors
26 W BTL and 2 × 13 W SE power
amplifiers
Preliminary specification
TDA8510J
FUNCTIONAL DESCRIPTION
The TDA8510J contains four identical amplifiers and can
be used for two Single-Ended (SE) channels (fixed gain
20 dB) and one Bridge-Tied Load (BTL) channel (fixed
gain 26 dB). Special features of the device are:
During this short-circuit condition, pin 16 is LOW for 20 ms
and HIGH for 50 µs (see Fig.5).
The power dissipation in any short-circuit condition is very
low.
Mode select switch (pin 14)
• Low standby current (<100 µA)
• Low switching current (low cost supply switch)
• Mute facility.
To avoid switch-on plops, it is advised to keep the amplifier
in the mute mode during ≥100 ms (charging of the input
capacitors at pins 1, 3, 15 and 17). This can be achieved
by:
• Microcontroller control
• External timing circuit (see Fig.8).
Diagnostic output (pin 16)
DYNAMIC DISTORTION DETECTOR (DDD)
At the onset of clipping of one or more output stages, the
dynamic distortion detector becomes active and pin 16
goes LOW. This information can be used to drive a sound
processor or DC volume control to attenuate the input
signal and thus limit the distortion. The output level of
pin 16 is independent of the number of channels that are
clipping (see Figs 3 and 4).
SHORT-CIRCUIT PROTECTION
When a short-circuit occurs at one or more outputs to
ground or to the supply voltage, the output stages are
switched off until the short-circuit is removed and the
device is switched on again, with a delay of approximately
20 ms, after removal of the short-circuit. During this
short-circuit condition, pin 16 is continuously LOW.
When a short-circuit across the load of one or more
channels occurs the output stages are switched off for
approximately 20 ms. After that time it is checked during
approximately 50 µs to see whether the short-circuit is still
present. Due to this duty cycle of 50 µs/20 ms the average
current consumption during this short-circuit condition is
very low (approximately 40 mA).
handbook, halfpage VO
0
V16
VP
0
MGA705
t
Fig.3 Distortion detector waveform; BTL channel.
handbook, halfpage VO
0
V16
VP
0
MGA706
t
Fig.4 Distortion detector waveform; SE channels.
1999 Dec 14
5
Free Datasheet http://www.datasheet4u.com/
5 Page 
Philips Semiconductors
26 W BTL and 2 × 13 W SE power
amplifiers
TEST AND APPLICATION INFORMATION
Preliminary specification
TDA8510J
handbook, full pagewidth
mode
switch
10
kΩ
VP
100 2200
nF µF
220 nF 1
input 1
14 16 5 13
TDA8510J
+
−
6
60
kΩ
220 nF
input 2
ground (signal)
3
2
supply voltage
ripple rejection
4
100 1/2VP
µF
15
60
kΩ
60
kΩ
470 nF
inputs
3 and 4
60
kΩ
17
−8
+
reference
voltage
9
− 10
+
− 12
+
1000 µF
RL1
2Ω
1000 µF
RL1
2Ω
not connected
RL2
4Ω
7 11
MGL429
power ground (substrate)
1999 Dec 14
Fig.7 Application diagram.
11
Free Datasheet http://www.datasheet4u.com/
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet 8510J.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| 8510J | TDA8510J | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |