|
|
|
부품번호 | E1L52-YC1Ax-03 기능 |
|
|
기능 | Green LED | ||
제조업체 | Toyoda | ||
로고 | |||
Mono-Color Lamps / Bluish-Green Lamp Series
5 Round type
Viewing angle 23 Reference
Round
Power Dissipation
DC Forward Current
Pulsed Forward Current
Reverse Voltage
Operating Temperature
Storage Temperature
1Duty 1/10 Pulse Width 100 s.
2 See table for Luminous Intensity Ranks.
3 Axial Direction (Luminous Intensity)
4 Devices are sorted by above wavelength ranges.
Please contact sales person, if you request to designate Luminous Intensity Ranks.
Please use the Part Number above for your order.
When soldering, leave 4 mm of minimum clearance between the resin
and the soldering point.
Free Datasheet http://www.datasheet4u.net/
Soldering
Conditions
Lead form-
ing and cut
Assembly
Static
Electricity
Safety
Precautions
When soldering, leave minimum clearance between the resin and the soldering point.
Maximum allowable soldering conditions are:
Solder dipping : 260 degrees C max., 5 seconds max., one time.
Soldering iron : 350 degrees C max., 5 seconds max., one time, power 40W max.
Contact between molten solder and the resin must be avoided.
Adjusting the soldered position after soldering must be avoided.
In soldering, do not put any stress to the lead frame, particularly when heated.
When other SMD parts on the same circuit board and adhesive is to be cured, maximum allowable conditions are :
120 degrees C max., 60 seconds max.
Lead forming must be done below the tie bar cutting position.
When forming a lead, do not stress the resin case.
Cutting lead forming must be done before soldering.
Cutting the lead frame at high temperature may cause problems. Cut the lead frame at room temperature.
Do not put any stress to the lead frame while assembling.
When mounting Products onto boards such as printed wired board, the pitch between the two holes of such boards must the
pitch of the Products.
These products are so sensitive to static electricity charge that users are required to handle with care. Particularly if an
over-current and over-voltage which exceeds the Absolute Maximum Rating of Products is applied, the overflow in
energy may cause damage to, or possibly result in electrical destruction of, the Products. Customer is requested to
adequate countermeasures against static electricity charge and surge when handling Products.
A protection device should be installed in the LED driving circuit, which does not exceed the max. rating for surge
current during on/off switching.
Proper grounding of Products (via 1M ), use of conductive mat, semiconductive working uniform and shoes, and
semiconductive containers are considered to be effective as countermeasures against static electricity and surge.
When the electrified product touches the low resistance part such as the metal face, there is a high possibility that it may
be charged due to radical electric discharge.
When grinding, use of resisting element such as conductive mat is effective for parts where the product directly touches.
A tip of soldering iron is requested to be grounded. An ionizer should also be installed where risk of static
generation is high.
If the contermeasures mentioned above are implemented, LED can work well.
Users are required to confirm those countermeasures when problems are caused by static electricity.
Users are requested to comply with the laws and public regulations concerning safety.
The light output of the Products may cause injuries to human eyes in circumstances where the Products are viewed directly
for more than a few seconds.
Free Datasheet http://www.datasheet4u.net/
4페이지 | |||
구 성 | 총 5 페이지수 | ||
다운로드 | [ E1L52-YC1Ax-03.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
E1L52-YC1Ax-02 | Green LED | Toyoda |
E1L52-YC1Ax-03 | Green LED | Toyoda |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |