|
|
PDF KTC144 Data sheet ( Hoja de datos )
| Número de pieza | KTC144 | |
| Descripción | Tradesman Series Manual | |
| Fabricantes | Black & Decker | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de KTC144 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
53"%&4."/4&3*&4
®
KTC144
Free Datasheet http://www.datasheet-pdf.com/
1 page  
• Do not probe the charger.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do
not play with the appliance.
• If the supply cord of the charger is damaged, it must
be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
LABELS ON THE CHARGER
The following symbols are found on your charger:
Your charging base is double insulated; therefore no
earth wire is required. Always check that the power
supply corresponds to the voltage on the rating plate.
The charging base is intended for indoor use only.
S• PECIFIC SAFETY RULES
Hold tool by insulated gripping surfaces when
performing an operation where the tool may
contact hidden wiring. Contact with a “live” wire
will also make exposed metal parts of the tool “live”
• and shock the operator.
When working on a ladder or on scaffolding be
sure to lay the tool down on its side when not in
use. Some tools with large battery packs will stand
• upright but may be easily knocked over.
Avoid touching the tip of a drill bit just after drilling,
• as it may be hot.
When fitting and changing accessories, always use
• the instructions supplied with the accessory.
Should your tool develop a fault, do not try to fix it
yourself, but take it to one of our authorized repair
agents.
SYMBOLS
The label on your tool may include the following symbols:
V volts
A Amperes
Hz Hertz
W Watts
min. Minutes
Alternating current
Direct current
no No load speed
Class II Construction
Earthing terminal
Safety alert symbol
…/min Revolutions or reciprocation per minute
…/bpm Beats per minute
ENGLISH
FEATURES (FIG. 1)
a. Variable speed switch
b. Forward/reverse slider
c. Keyless chuck
d. Mode selector/torque adjustment collar
e. Collar settings
f. Two gear selector
g. Grip
h. Battery pack
i. Release buttons
j. Charger
k. Charging indicator
ASSEMBLY AND ADJUSTMENT
WARNING: Prior to assembly and adjustment,
always remove the battery pack. Always switch off the
tool before inserting or removing the battery pack.
WARNING: Use only Black &Decker battery packs
and chargers.
INSERTING AND REMOVING THE BATTERY PACK
FROM THE TOOL (FIG. 2)
WARNING: To reduce the risk of serious
personal injury, turn tool off and disconnect
battery pack making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
TO INSTALL THE BATTERY PACK INTO THE TOOL
HANDLE
1. Align the base of the tool with the notch inside the
tool’s handle (fig. 2).
2. Slide the battery pack firmly into the handle until you
hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release buttons (i) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in
the charger section of this manual.
INSERTING AND REMOVING BITS (FIG. 1, 4)
1. Open the chuck by turning the sleeve (p) counter-
clockwise and insert the bit shank.
2. Place the bit in the chuck as far as it will go and lift
slightly before tightening.
3. Tighten firmly by turning the sleeve clockwise.
4. To remove the bit, proceed in reverse order.
5
Free Datasheet http://www.datasheet-pdf.com/
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet KTC144.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| KTC144 | Tradesman Series Manual | Black & Decker |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |