|
|
|
부품번호 | V375A15C600A 기능 |
|
|
기능 | DC-DC Converter Module | ||
제조업체 | VICOR | ||
로고 | |||
45
Features
• DC input range: 250 - 425V
• Input surge withstand: 500V for 100ms
• DC output: 15V
• Programmable output: 10 to 110%
• Regulation: ±0.2% no load to full load
• Efficiency: 87%
• Maximum operating temperature:
100°C at full load
• Power density: 119W/cubic inch
• Height above board: 0.43 in. (10,9 mm)
• Parallelable, with N+M fault tolerance
• Low noise ZCS/ZVS architecture
375Vin / 15Vout / 600Watts
DC-DC Converter Module
Model Number V375A15C600A*
Typical Applications: distributed power;
off-line systems using power PFC front-ends;
electric vehicles
Shown actual size:
4.6 x 2.2 x 0.5 in
117 x 56 x 12,7 mm
Product Overview
Absolute Maximum Ratings
This DC-DC converter module uses
2nd Generation power processing, control
and packaging technologies to provide the
performance, flexibility and cost effectiveness
expected of a mature power component.
Parameter
+In to –In voltage
+In to –In voltage
Rating
-0.5 to +425.0
500
For example, a plated-cavity core transformer PC to –In voltage
-0.5 to +7.0
couples widely separated primary and
PR to –In voltage
-0.5 to +7.0
secondary windings, resulting in low in-to-
out parasitic capacitance and noise.
High frequency ZCS/ZVS switching,
advanced power semiconductor packaging
+Out to –Out voltage
+Sense to –Out voltage
–Sense to –Out voltage
-0.5 to +20.0
-0.5 to +20.0
1.0
and thermal management provide high
SC to –Out voltage
-0.5 to +1.5
power density with low temperature
gradients. Extensive use of silicon
integration results in 1/3 the part count
of a 1st Generation converter.
Isolation voltage (in to out)
Isolation voltage (in to base)
Isolation voltage (out to base)
3000
1550
500
* Part Numbering
Storage temperature (C–Grade) -40 to +125
Operating temperature (C–Grade) -20 to +100
V 375 A 5 C 400 A
Input Voltage
24 = 24Vin
48 = 48Vin
300 = 300Vin
375 = 375Vin
A = Maxi
B = Mini
C = Micro
Output
Voltage
Output
Power
Pin
Style
Product Grade Temperatures (°C)
Grade Storage Operating
C = - 40 to +125 - 20 to +100
T = - 40 to +125 - 40 to +100
H = - 55 to +125 - 40 to +100
M = - 65 to +125 - 55 to +100
Base-
plate
Pin soldering temperature
Pin soldering temperature
Mounting torque
500 (260)
750 (390)
5 (0.57)
Thermal Resistance and Capacity
Parameter
Min
For pin styles see page 6. Slotted baseplate
(style 1) requires no designator. For
threaded baseplate add a “2” to the end of
the part number. For thru-hole, add a “3”.
See page 7 for dimensions.
Baseplate to sink; flat, greased surface
Baseplate to sink; thermal pad (P/N 20263)
Baseplate to ambient
Baseplate to ambient; 1000 LFM
Thermal capacity
Unit
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vrms
Vrms
Vrms
°C
°C
°F (°C)
°F (°C)
in-lbs (N-m)
Notes
<100ms
See part numbering chart on this
page for other product grades.
Baseplate
<5 sec; wave solder
<7 sec; hand solder
6 each, # 4-40 or M3
Typ Max Unit
0.08 °C/Watt
0.07 °C/Watt
4.9 °C/Watt
1.1 °C/Watt
165 Watt-sec/°C
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
V375A15C600A DC-DC Converter
Set your site on VICOR at www.vicorpower.com
Rev. 5.2
Page 1 of 8
Free Datasheet http://www.Datasheet4U.com
CONTROL FUNCTIONS - PC PIN
Module Enable/Disable
The module may be disabled by pulling PC below 2.3V with
respect to the –Input. This may be done with an open collector
transistor, relay, or optocoupler. Multiple converters may be
disabled with a single transistor or relay either directly or via
“OR’ing” diodes. See Figure 1.
Primary Auxiliary Supply
At 5.7V, PC can source up to 1.5mA. In the example shown in
Figure 3, PC powers a module enabled LED.
Module Alarm
The module contains “watchdog” circuitry which monitors
input voltage, operating temperature and internal operating
parameters. In the event that any of these parameters are
outside of their allowable operating range, the module will shut
down and PC will go low. PC will periodically go high and the
module will check to see if the fault (as an example,
overtemperature) has cleared. If the fault has not been cleared,
PC will go low again and the cycle will restart. The SC pin will
go low in the event of a fault and return to its normal state after
the fault has been cleared. See Figures 2 and 4.
+In
PC
Disable
Disable = PC <2.3V
PR
–In
Figure 1—Module enable/disable.
"Module
Enabled"
4kΩ
+In
PC
PR
–In
Figure 3—LED on-state indicator.
Input Undervoltage
Input Overvoltage
+In
SW1
Auto
Restart
Overtemperature
Module Faults
PC
2-20ms typ.
f (VIN)
50Ω
SW1, 2, & 3
PR
shown in
SW2
SW3 1K
"Fault" position
5.7Vdc
–In (0-3mA)
1.23
Vdc 6K
+Out
+S
SC
–S
–Out
Figure 2—PC/SC module alarm logic.
Fault
5.7V
PC
SC 1.23V
40µs typ.
2-20ms typ.
Figure 4—PC/SC module alarm timing.
Optocoupler
4kΩ
+In
PC
PR
–In
+Out
+S
SC
–S
–Out
1.00V
Alarm
Figure 5—Isolated on-state indicator.
Figure 6—Secondary side on-state indicator.
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
V375A15C600A DC-DC Converter
Set your site on VICOR at www.vicorpower.com
Rev. 5.2
Page 4 of 8
Free Datasheet http://www.Datasheet4U.com
4페이지 MECHANICAL DRAWINGS
MODULE OUTLINE
Converter Pins
No. Function Label
1 +In
+
2
Primary
Control
PC
3 Parallel PR
4 –In
–
5 –Out
–
6 –Sense –S
7
Secondary
Control
SC
8 +Sense +S
9 +Out
+
PINS: TIN/LEAD
HOT SOLDER DIP
0.50 ±0.02
12,7 ±0,5
0.300±0.015
7,62±0,38
0.23 (REF)
5,8
0.300±0.015
7,62±0,38
2.20
55,9
1.74
44,2
4-40 UNC-2B 0.12* 0.20**
Thru (4X)***
3,1 5,08
(Style 2 and 3 only)
0.01
0.50
12,7
12
34
4.200
106,68
0.38 (2X)
9,6
ALUMINUM
BASEPLATE
1.80
45,7
3.60
4.60 91,4
116,8
9 87 6 5
2.00
50,8
Slotted (Style 1)
or
Threaded (Style 2)
4-40 UNC-2B (6X)
or
Thru Hole (Style 3)
#30 Drill Thru (6X)
(0.1285)
0.400
10,16
0.700
17,78
1.000
25,40
1.400
35,56
PCB MOUNTING SPECIFICATIONS
0.180
DIA,(2X)
4,57
0.080
DIA,(7X)
2,03
0.43
10,9
R 0.06 (3X)
1,5
0.54
13,7
(9X)
Pin Style 1&S
(Short Pin)
0.62
15,7
(9X)
Pin Style 2&N
(Long Pin)
2.20
55,9
(REF)
* Style 1 baseplate only
** Style 2 & 3 baseplates
*** Reserved for Vicor accessories
Not for mounting
ALL MARKINGS
THIS SURFACE
PCB
THICKNESS
0.062
1,57
±0.010
±0,25
R 0.06 (4X)
1,5
1.790
45,47
INBOARD
SOLDER
MOUNT
PLATED
THRU HOLE
DIA
(7X)
(2X)
PIN STYLE 1&S
0.094 ±0.003
2,39 ±0,08
0.194 ±0.003
4,93 ±0,08
0.178
4,52
12
34
ONBOARD
SOLDER
MOUNT
PIN STYLE 2&N
0.094 ±0.003
2,39 ±0,08
0.194 ±0.003
4,93 ±0,08
ALUMINUM
BASEPLATE
PINS STYLES
STYLE 1 & 2: TIN/LEAD
HOT SOLDER DIPPED
STYLE S & N: GOLD PLATED COPPER
4.200*
106,68
3.844
97,64
0.10
2,5
0.10 X 45°
2,5
CHAMFER
FULL R (6X)
0.13 (6X)
3,3
Use a
4-40 Screw (6x)
Torque to:
5 in-lbs
0.57 N-m
9 87 6 5
0.400*
10,16
0.195
4,95
0.700*
17,78
1.000*
25,40
1.400*
35,56
* DENOTES
TOL = ±0.003
±0,08
0.43 0.53
10,9 13,5
Unless otherwise specified,
dimensions are in inches
mm
Decimals Tol.
Angles
0.XX
±0.01
±0,25
±1°
0.XXX ±0.005
±0,127
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
V375A15C600A DC-DC Converter
Set your site on VICOR at www.vicorpower.com
Rev. 5.2
Page 7 of 8
Free Datasheet http://www.Datasheet4U.com
7페이지 | |||
구 성 | 총 8 페이지수 | ||
다운로드 | [ V375A15C600A.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
V375A15C600A | DC-DC Converter Module | VICOR |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |