|
|
PDF AD584 Data sheet ( Hoja de datos )
| Número de pieza | AD584 | |
| Descripción | Precision Voltage Reference | |
| Fabricantes | Analog Devices | |
| Logotipo |  |
|
1. AD584  Hay una vista previa y un enlace de descarga de AD584 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
|
No Preview Available !
Data Sheet
FEATURES
Four programmable output voltages
10.000 V, 7.500 V, 5.000 V, and 2.500 V
Laser-trimmed to high accuracies
No external components required
Trimmed temperature coefficient
15 ppm/°C maximum, 0°C to 70°C (AD584K)
15 ppm/°C maximum, −55°C to +125°C (AD584T)
Zero output strobe terminal provided
2-terminal negative reference: capability (5 V and above)
Output sources or sinks current
Low quiescent current: 1.0 mA maximum
10 mA current output capability
MIL-STD-883 compliant versions available
GENERAL DESCRIPTION
The AD584 is an 8-terminal precision voltage reference offering
pin programmable selection of four popular output voltages:
10.000 V, 7.500 V, 5.000 V and 2.500 V. Other output voltages,
above, below, or between the four standard outputs, are available by
the addition of external resistors. The input voltage can vary
between 4.5 V and 30 V.
Laser wafer trimming (LWT) is used to adjust the pin
programmable output levels and temperature coefficients,
resulting in the most flexible high precision voltage reference
available in monolithic form.
In addition to the programmable output voltages, the AD584
offers a unique strobe terminal that permits the device to be
turned on or off. When the AD584 is used as a power supply
reference, the supply can be switched off with a single, low power
signal. In the off state, the current drained by the AD584 is reduced
to approximately 100 µA. In the on state, the total supply current is
typically 750 µA, including the output buffer amplifier.
The AD584 is recommended for use as a reference for 8-, 10-,
or 12-bit digital-to-analog converters (DACs) that require an
external precision reference. In addition, the device is ideal for
analog-to-digital converters (ADCs) of up to 14-bit accuracy,
either successive approximation or integrating designs, and in
general, it can offer better performance than that provided by
standard self-contained references.
Pin Programmable,
Precision Voltage Reference
AD584
PIN CONFIGURATIONS
TAB
8
10.0V 1 V+ 7 CAP
AD584
5.0V 2 TOP VIEW 6 VBG
(Not to Scale)
2.5V 3
5 STROBE
4
COMMON
Figure 1. 8-Pin TO-99
10.0V 1
5.0V 2
2.5V 3
COMMON 4
AD584
TOP VIEW
(Not to Scale)
8 V+
7 CAP
6 VBG
5 STROBE
Figure 2. 8-Lead PDIP
The AD584J and AD584K are specified for operation from 0°C
to +70°C, and the AD584S and AD584T are specified for the
−55°C to +125°C range. All grades are packaged in a hermetically
sealed, eight-terminal TO-99 metal can, and the AD584J and
AD584K are also available in an 8-lead PDIP.
PRODUCT HIGHLIGHTS
1. The flexibility of the AD584 eliminates the need to design-
in and inventory several different voltage references.
Furthermore, one AD584 can serve as several references
simultaneously when buffered properly.
2. Laser trimming of both initial accuracy and temperature
coefficient results in very low errors overtemperature
without the use of external components.
3. The AD584 can be operated in a 2-terminal Zener mode at
a 5 V output and above. By connecting the input and the
output, the AD584 can be used in this Zener configuration
as a negative reference.
4. The output of the AD584 is configured to sink or source
currents. This means that small reverse currents can be
tolerated in circuits using the AD584 without damage to
the reference and without disturbing the output voltage
(10 V, 7.5 V, and 5 V outputs).
5. The AD584 is available in versions compliant with MIL-STD-
883. Refer to the Analog Devices current AD584/883B data
sheet for detailed specifications. This can be found under the
Additional Data Sheets section of the AD584 product page.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibilityisassumedbyAnalogDevices for itsuse,nor foranyinfringementsofpatentsor other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©1978–2012 Analog Devices, Inc. All rights reserved.
Free Datasheet http://www.Datasheet4U.com
1 page  
Data Sheet
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
Input Voltage VIN to Ground
Power Dissipation at 25°C
Operating Junction Temperature Range
Lead Temperature (Soldering 10 sec)
Thermal Resistance
Junction-to-Ambient (H-08A)
Rating
40 V
600 mW
−55°C to +125°C
300°C
150°C/W
Stresses above those listed under Absolute Maximum Ratings may
cause permanent damage to the device. This is a stress rating
only; functional operation of the device at these or any other
conditions above those indicated in the operational section of
this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device
reliability.
ESD CAUTION
AD584
Rev. C | Page 5 of 12
Free Datasheet http://www.Datasheet4U.com
5 Page 
Data Sheet
OUTLINE DIMENSIONS
REFERENCE PLANE
0.1850 (4.70)
0.1650 (4.19)
0.0400 (1.02) MAX
0.0400 (1.02)
0.0100 (0.25)
0.5000 (12.70)
MIN
0.2500 (6.35) MIN
0.0500 (1.27) MAX
0.1000 (2.54)
BSC
0.1600 (4.06)
0.1400 (3.56)
5
46
0.2000
(5.08)
BSC
3
2
0.0190 (0.48)
0.0160 (0.41)
0.0210 (0.53)
0.0160 (0.41)
0.1000
(2.54)
BSC
7
8
1
0.0340 (0.86)
0.0280 (0.71)
45° BSC
0.0450 (1.14)
0.0270 (0.69)
BASE & SEATING PLANE
COMPLIANT TO JEDEC STANDARDS MO-002-AK
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 20. 8-Pin Metal Header [TO-99]
(H-08)
Dimensions shown in inches and (millimeters)
0.400 (10.16)
0.365 (9.27)
0.355 (9.02)
85
14
0.210 (5.33)
MAX
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.100 (2.54)
BSC
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.060 (1.52)
MAX
0.015
(0.38)
MIN
SEATING
PLANE
0.015 (0.38)
GAUGE
PLANE
0.005 (0.13)
MIN
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.430 (10.92)
MAX
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 21. 8-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body (N-8)
Dimensions shown in inches and (millimeters)
AD584
Rev. C | Page 11 of 12
Free Datasheet http://www.Datasheet4U.com
11 Page | ||
| Páginas | Total 12 Páginas | |
| PDF Descargar | [ Datasheet AD584.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AD580 | High Precision 2.5 V IC Reference | Analog Devices |
| AD581 | High Precision 10 V IC Reference | Analog Devices |
| AD582 | Low Cost Sample/Hold Amplifier | Analog Devices |
| AD5821 | single 10-bit digital-to-analog converter | Analog Devices |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |