|
|
PDF EMC5046 Data sheet ( Hoja de datos )
| Número de pieza | EMC5046 | |
| Descripción | Standalone Linear Li-Ion Charger | |
| Fabricantes | Elite Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de EMC5046 (archivo pdf) en la parte inferior de esta página. Total 19 Páginas | ||
|
No Preview Available !
ESMT/EMP
EMC5046
Standalone Linear Li-Ion Charger (1A, two-cell)
with Thermal Regulation
General Description
The EMC5046 is a complete linear charger for
two-cell lithium-ion batteries. With E-SOP-8 packages
and few external components, EMC5046 is well
suited for portable applications.
No external sense resistor and blocking diode are
required. Charging current can be programmed
externally with a single resistor. The built-in thermal
regulation facilitates charging with maximum power
without risk of overheating.
The EMC5046 always preconditions the battery with
1/10 of the programmed charge current at the
beginning of a charge cycle, after it verifies that the
battery can be fast-charged. The EMC5046
automatically terminates the charge cycle when
the charge current drops to 1/10th the programmed
value after the final float voltage is reached.
The EMC5046 features 13.5V maximum rating
voltage for AC adapter, and it provides the charge
current up to 1.0A. Other features include battery
temperature monitoring, reverse current protection,
shutdown mode, charging current monitor, under
voltage lockout, automatic recharge and status
indicator.
Features
Programmable charge current up to 1.0A
No MOSFET, sense resistor or blocking diode
required
Complete linear charger in E-SOP-8 for
two-cell li-ion batteries
Thermal regulation maximizes charge rate
without risk of overheating
Preset 8.4V charge voltage with ±1%
accuracy
Automatic recharge
Charge status indicator
C/10 charge termination
5.8V trickle charge threshold
Battery reverse leakage current less than 1uA
Applications
Wireless handsets
Hand-held instruments
Portable information appliances
Elite Semiconductor Memory Technology Inc./Elite MicroPower Inc.
Publication Date: Jun. 2012
Revision: 0.2
1/19
1 page  
ESMT/EMP
Functional Block Diagram
EMC5046
IN
CHG_SB
PGOODB
GND
ACIN
BAT
5.8V
BAT
Body
Switch
BS BS
Regulation
Controller
-+
Temperature
Controller
1.5V
0.15V
UVLO/OVP
BAT
8.1V
Logic
Controller
0.15V
2.15V
-+
BS
BATT
1.2V
ISETA
Disable
ENB
FIG.1 Functional Block Diagram of EMC5046
Elite Semiconductor Memory Technology Inc./Elite MicroPower Inc.
Publication Date: Jun. 2012
Revision: 0.2
5/19
5 Page 
ESMT/EMP
EMC5046
Operation
The EMC5046 is a two-cell lithium-ion battery charger using a constant-current/constant-voltage algorithm. It
can deliver up to 1.0A of charge current (using a good thermal PCB layout) with a final float voltage accuracy
of ±1%. The EMC5046 includes an internal P-channel power MOSFET and thermal regulation circuitry. No
blocking diode or external current sense resistor is required; thus, the basic charger circuit requires only two
external components.
Normal Charge Cycle
A charge cycle begins when the voltage at the IN pin rises above the UVLO threshold level and a 1% program
resistor is connected from the ISETA pin to ground or when a battery is connected to the charger output. If the
BATT pin is less than 5.8V, the charger enters trickle charge mode. In this mode, the EMC5046 supplies
approximately 1/10 the programmed charge current to bring the battery voltage up to a safe level for full
current charging. When the BATT pin voltage rises above 5.8V, the charger enters constant-current mode,
where the programmed charge current is supplied to the battery. When the BATT pin approaches the final
float voltage (8.4V), the EMC5046 enters constant- voltage mode and the charge current begins to decrease.
When the charge current drops to 1/10 of the programmed value, the charge cycle ends.
Programming Charge Current
The charge current is programmed using a single resistor from the ISETA pin to ground. The battery charge
current is 500 times the current out of the ISETA pin. VSET is 1.5V when charging in constant-current mode. The
program resistor and the charge current are calculated using the following equations:
R SET
500V SET
I CHG
,
I CHG
500V SET
R SET
The charge current out of the BATT pin can be determined at any time by monitoring the ISETA pin voltage
using the following equation:
IBATT
VSET
RSET
500
Charge Termination
A charge cycle is terminated when the charge current falls to 1/10th the programmed value after the final
float voltage is reached. This condition is detected by using an internal, filtered comparator to monitor the
ISETA pin. When the ISETA pin voltage falls below 150mV for longer than TTERM (typically 1ms), charging is
terminated. The charge current is latched off and the EMC5046 enters standby mode, where the input supply
current drops to 150uA. (Note: C/10 termination is disabled in trickle charging and thermal limiting modes). The
EMC5046 draws no current from the battery in standby mode. This feature reduces the charge and discharge
cycles on the battery, further prolonging the battery life.
Any external source (VSET) that holds the ISETA pin above 150mV will prevent the EMC5046 from terminating a
charge cycle. However, if the ISETA pin is controlled by external source, current sourcing from the BATT pin can
be infinity (until the internal power MOSFET is burned out or the BATT pin voltage is close to its final float voltage),
and the formula for charge current is not valid anymore.
When charging, transient loads on the BATT pin can cause the ISETA pin to fall below 150mV for short periods of
time before the DC charge current has dropped to 1/10th the programmed value. The 1ms filter time (TTERM) on
the termination comparator ensures that transient loads of this nature do not result in premature charge cycle
termination. Once the average charge current drops below 1/10th the programmed value, the EMC5046
terminates the charge cycle and ceases to provide any current through the BATT pin. This is the standby mode,
and all loads on the BATT pin must be supplied by the battery. In the standby mode, any signal below the
manual shutdown threshold voltage (typically 2.15V) on the ISETA pin is transparent to EMC5046.
Elite Semiconductor Memory Technology Inc./Elite MicroPower Inc.
Publication Date: Jun. 2012
Revision: 0.2
11/19
11 Page | ||
| Páginas | Total 19 Páginas | |
| PDF Descargar | [ Datasheet EMC5046.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| EMC5040 | Standalone Linear Li-Ion Charger | Elite Semiconductor |
| EMC5040-42FF10NRR | Standalone Linear Li-Ion Charger | Elite Semiconductor |
| EMC5042 | Standalone Linear Li-Ion Charger | Elite Semiconductor |
| EMC5042-84FF10NRR | Standalone Linear Li-Ion Charger | Elite Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |