|
|
|
부품번호 | HCPL-0708060 기능 |
|
|
기능 | High Speed CMOS Optocoupler | ||
제조업체 | Agilent(Hewlett-Packard) | ||
로고 | |||
Agilent HCPL-0708
High Speed
CMOS Optocoupler
Data Sheet
Description
Available in SO-8 package, the
HCPL-0708 optocoupler utilizes the
latest CMOS IC technology to
achieve outstanding performance
with very low power consumption.
Basic building blocks of the HCPL-
Functional Diagram
NC 1
ANODE 2
8 VDD
7 NC
0708 are a high speed LED and a
CMOS detector IC. The detector
incorporates an integrated
photodiode, a high-speed trans-
impedance amplifier, and a voltage
comparator with an output driver.
Features
• +5 V CMOS compatibility
• 15 ns typical pulse width distortion
• 30 ns max. pulse width distortion
• 40 ns max. propagation delay
skew
• High speed: 15 MBd
• 60 ns max. propagation delay
• 10 kV/µs minimum common mode
rejection
• –40 to 100°C temperature range
• Safety and regulatory approvals
pending
– UL recognized
2500 V rms for 1 min. per
UL 1577 for HCPL-0708
– CSA component acceptance
Notice #5
– VDE 0884 (TUV) approved for
HCPL-0708 Option 060
CATHODE 3
NC 4
6 VO
5 GND
TRUTH TABLE
LED
OFF
ON
VO, OUTPUT
H
L
*A 0.1 µF bypass capacitor
must be connected between
pins 5 and 8.
Applications
• Scan drive in PDP
• Digital field bus isolation:
DeviceNet, SDS, Profibus
• Multiplexed data transmission
• Computer peripheral interface
• Microprocessor system interface
• DC/DC converter
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this
component to prevent damage and/or degradation which may be induced by ESD.
VDE 0884 Insulation Related Characteristics (Option 060)
Description
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤150 V rms
for rated mains voltage ≤300 V rms
for rated mains voltage ≤450 V rms
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b†
VIORM x 1.875 = VPR, 100% Production
Test with tm = 1 sec, Partial Discharge < 5 pC
Input to Output Test Voltage, Method a†
VIORM x 1.5 = VPR, Type and Sample Test,
tm = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage†
(Transient Overvoltage, tini = 10 sec)
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Thermal Derating curve, Figure 11.)
Case Temperature
Input Current
Output Power
Insulation Resistance at TS, V10 = 500 V
Symbol
VIORM
VPR
VPR
VIOTM
HCPL-0708 Option 060
I-IV
I-III
55/85/21
2
560
1050
840
4000
TS
IS,INPUT
PS,OUTPUT
RIO
150
150
600
≥109
Units
V peak
V peak
V peak
V peak
°C
mA
mW
Ω
†Refer to the front of the optocoupler section of the Isolation and Control Component Designer’s Catalog, under Product Safety Regulations section
(VDE 0884), for a detailed description.
Note: These optocouplers are suitable for “safe electrical isolation” only within the safety limit data. Maintenance of the safety data shall be
ensured by means of protective circuits.
Note: The surface mount classification is Class A in accordance with CECC 00802.
Absolute Maximum Ratings
Parameter
Storage Temperature
Ambient Operating Temperature[1]
Supply Voltages
Output Voltage
Average Output Current
Average Forward Input Current
Lead Solder Temperature
Solder Reflow Temperature Profile
Symbol
TS
TA
VDD
VO
IO
IF
Min. Max.
Units
–55 125
°C
–40 +100
°C
06
Volts
–0.5 VDD2 +0.5
2
Volts
mA
20 mA
260°C for 10 sec., 1.6 mm below seating plane
See Solder Reflow Temperature Profile Section
Figure
Recommended Operating Conditions
Parameter
Ambient Operating Temperature
Supply Voltages
Input Current (ON)
4
Symbol
TA
VDD
IF
Min.
–40
4.5
10
Max.
+100
5.5
16
Units
°C
V
mA
Figure
1, 2
4페이지 1000
100
IF
10 +
VF
–
1.0
TA = 25°C
0.1
0.01
0.001
1.1 1.2 1.3 1.4 1.5 1.6
VF – FORWARD VOLTAGE – V
8
VDD = 5.0 V
7 IOL = 20 µA
6
5
4
3
2
-40 0 25 85 100
TA – TEMPERATURE – °C
Figure 1. Typical input diode forward
characteristic.
Figure 2. Typical input threshold current vs.
temperature.
6.0
VDD = 5.0 V
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
-40 0 25 85 100
TA – TEMPERATURE – °C
Figure 3. Typical logic high O/P supply
current vs. temperature.
8.0
VDD = 5.0 V
7.5
7.0
6.5
6.0
5.5
5.0
4.5
4.0
-40 0 25 85 100
TA – TEMPERATURE – °C
Figure 4. Typical logic low O/P supply
current vs. temperature.
50
45
40
Tphl
35
VDD = 5.0 V
TA = 25 °C
30
25 Tplh
20
15
PWD
10
5
0
5 6 7 8 9 10 11 12 13 14
IF – PULSE INPUT CURRENT – mA
Figure 5. Typical switching speed vs. pulse
input current.
7
7페이지 | |||
구 성 | 총 10 페이지수 | ||
다운로드 | [ HCPL-0708060.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
HCPL-0708060 | High Speed CMOS Optocoupler | Agilent(Hewlett-Packard) |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |